3com officeconnect switch 5 3c16793 инструкция

1

POSITIONING YOUR SWITCH

OfficeConnect

®

Switch 5

(3C16793)

Switch 8

(3C16794)

Thank you for purchasing the OfficeConnect Switch. The OfficeConnect
Switch is an efficient and inexpensive way of creating or expanding an existing
network. The Switch is ideal for use with other OfficeConnect products, as
shown in Figure 1. It is compact and attractively designed for desktop use. The
Switch is part of the OfficeConnect range and can be stacked with other
OfficeConnect units.

Your Package Contains: 

●

One OfficeConnect Switch

●

One power adapter for use with the Switch

●

Four rubber feet

●

This Installation Guide

●

One Support and Safety Information Sheet

●

One Warranty Flyer

About This Guide

This Installation guide will use the term ‘Switch’ when referring to the
OfficeConnect Switch 5 or Switch 8.

This Installation Guide covers installation of the OfficeConnect Switch 5 and
Switch 8. The instructions are the same for both models, except Switch 5 users
should substitute ‘port 5’ for ‘port 8’ throughout.

Part No: DIA1679-3AAA02  Published: August 2001

INTRODUCTION

ABOUT YOUR SWITCH

OfficeConnect

Switch

10BASE-T

OfficeConnect hub

100BASE-TX

OfficeConnect hub

1

2

3

4

5

Figure 1 Small Network with OfficeConnect Switch (Circle Shows Units
Clipped Together).

Safety Information

WARNING: Please read the ‘Important Safety Information’ section in the
Support and Safety Information sheet before you start.

VORSICHT: Bitte lesen Sie den Abschnitt ‘Wichtige Sicherheitsinformationen’
sorgfältig durch, bevor Sie das Gerät einschalten.

AVERTISSEMENT: Veuillez lire attentivement la section «Consignes
importantes de sécurité» avant de mettre en route.

When positioning your Switch, ensure:

●

It is out of direct sunlight and away from sources of heat.

●

Cabling is away from power lines, fluorescent lighting fixtures, and sources
of electrical noise such as radios, transmitters and broadband amplifiers.

●

Water or moisture cannot enter the case of the unit.

●

Air flow around the unit and through the vents in the side of the case is
not restricted. We recommend you provide a minimum of 25mm (1in.)
clearance.

Using the Rubber Feet

Use the four self-adhesive rubber feet to prevent your Switch from moving
around on your desk or when stacking with other flat top OfficeConnect
units. Only stick the feet to the marked areas at each corner of the underside
of your Switch. 

Using a Stacking Clip

Use a stacking clip when stacking your Switch with curved OfficeConnect
units. Stacking clips are only supplied with curved OfficeConnect units. The
stacking clip allows you to stack units neatly and securely. Refer to user guide
of the curved unit for more details on how to use the stacking clip.

Wall Mounting

There are two slots on the underside of the OfficeConnect Switch that can be
used for wall mounting. 3Com recommends that you mount the Switch with
the LEDs facing upwards to prevent dust entering the ports. 

When wall mounting the unit, ensure that it is within reach of the power
outlet.

You need two suitable screws. Ensure that the wall you are going to use is
smooth, flat, dry and sturdy. Make two screw holes which are 150mm (5.9in.)
apart. Fix the screws into the wall, leaving their heads 3mm (0.12in.) clear of
the wall surface.

Remove any connections to the Switch and locate it over the screw heads.
When in line, gently push the Switch on to the wall and move it downwards
to secure. When making connections, be careful not to push the Switch up
and off the wall.

CAUTION: Only wall mount single units, do not wall mount stacked
units.

Also available from 3Com, is the OfficeConnect Mounting Unit (part
number 3C16765). This allows you to firmly secure a stack of
OfficeConnect devices to the desktop or onto a shelf in a rack.

WARNING: RJ-45 Ports

These are shielded RJ-45 data sockets. They cannot
be used as standard traditional telephone sockets,
or to connect the unit to a traditional PBX or public
telephone network. Only connect RJ-45 data
connectors, network telephony systems, or network
telephones to these sockets. Either shielded or
unshielded data cables with shielded or unshielded
jackets can be connected to these data sockets.

AVERTISSEMENT : Points d’accès RJ-45

Prises RJ-45 blindées. Ces prises ne peuvent servir
comme prises téléphone standard et ne permettent
pas la connexion de l’appareil à un système PBX ni à
un réseau téléphonique public. N’y branchez que
des prises RJ-45 mâles adaptées, ou des systèmes de
réseaux téléphoniques. Il est possible d’y brancher
des câbles blindés ou non comportant des prises de
type Jack (blindées ou non).

VORSICHT: RJ-45-Porte

RJ-45-Portes. Diese Portes sind geschützte
Datensteckdosen. Sie dürfen weder wie normale
traditionelle Telefonsteckdosen noch für die
Verbindung der Einheit mit einem traditionellenm
privatenm oder öffentlichenm Telefonnetzwerk
gebraucht werden. Nur RJ-45-Datenansclußhlüsse,
Telefonnetzsysteme oder Netztelefone an diese
Steckdosen anschließen. Entweder geschützte oder
ungeschützte Buchsen dürfen an diese
Datensteckdosen angeschlossen werden.

1 Power LED

green

Indicates that the Switch is powered on.

2 Five or Eight Port Status LEDs

green (100Mbps link) / yellow (10Mbps link)

If the LED is on, the link between the port and the
next piece of network equipment is OK. If the LED is
flashing, the link is OK and data is being transmitted
or received. If the LED is off, nothing is connected, or
the connected device is switched off, or there is a
problem with the connection (refer to the «Problem
Solving» section).

3 Power Adapter socket

Only use the power adapter that is supplied with
this Switch. Do not use any other adapter.

4 Uplink/Normal switch

Affects the operation of port 8. If you are
connecting another unit (such as a Hub or Switch)
to port 8, set to Uplink (in), otherwise set to Normal
(out). Refer to «Connecting Workstations and Other
Equipment to your Switch».

Note: For the Switch 5, substitute ‘port 5’ for 
‘port 8’.

5 Five or Eight 10/100 ports

Use suitable TP cable with RJ-45 connectors. You
can connect your Switch to a workstation, or any
other piece of equipment that has a 10BASE-T or
100BASE-TX port. Each port is capable of
autosensing for 10Mbps or 100Mbps operation.
Ports operate in half-duplex mode as well as full
duplex mode.

OfficeConnect Switch — Front

OfficeConnect Switch — Rear

Installation Guide

Installation Guide

OfficeConnect

®

Switch 5

(3C16793)

Switch 8

(3C16794)

INTRODUCTION

Thank you for purchasing the OfficeConnect Switch. The OfficeConnect

Switch is an efficient and inexpensive way of creating or expanding an existing

network. The Switch is ideal for use with other OfficeConnect products, as

shown in Figure 1. It is compact and attractively designed for desktop use. The

Switch is part of the OfficeConnect range and can be stacked with other

OfficeConnect units.

●

Your Package Contains:

One OfficeConnect Switch

●

One power adapter for use with the Switch

●

Four rubber feet

●

This Installation Guide

●

One Support and Safety Information Sheet

●

One Warranty Flyer

About This Guide

This Installation guide will use the term ‘Switch’ when referring to the

OfficeConnect Switch 5 or Switch 8.

This Installation Guide covers installation of the OfficeConnect Switch 5 and

Switch 8. The instructions are the same for both models, except Switch 5 users

should substitute ‘port 5’ for ‘port 8’ throughout.

Part No: DIA1679-3AAA02 Published: August 2001

ABOUT YOUR SWITCH

OfficeConnect Switch — Front

1

2

1 Power LED

4 Uplink/Normal switch

green

Affects the operation of port 8. If you are

connecting another unit (such as a Hub or Switch)

Indicates that the Switch is powered on.

to port 8, set to Uplink (in), otherwise set to Normal

2 Five or Eight Port Status LEDs

(out). Refer to «Connecting Workstations and Other

green (100Mbps link) / yellow (10Mbps link)

Equipment to your Switch».

If the LED is on, the link between the port and the

Note: For the Switch 5, substitute ‘port 5’ for

next piece of network equipment is OK. If the LED is

‘port 8’.

flashing, the link is OK and data is being transmitted

5 Five or Eight 10/100 ports

or received. If the LED is off, nothing is connected, or

Use suitable TP cable with RJ-45 connectors. You

the connected device is switched off, or there is a

can connect your Switch to a workstation, or any

problem with the connection (refer to the «Problem

other piece of equipment that has a 10BASE-T or

Solving» section).

100BASE-TX port. Each port is capable of

3 Power Adapter socket

autosensing for 10Mbps or 100Mbps operation.

Only use the power adapter that is supplied with

Ports operate in half-duplex mode as well as full

this Switch. Do not use any other adapter.

duplex mode.

10BASE-T

OfficeConnect hub

OfficeConnect

Switch

100BASE-TX

OfficeConnect hub

Figure 1 Small Network with OfficeConnect Switch (Circle Shows Units

Clipped Together).

OfficeConnect Switch — Rear

3

WARNING: RJ-45 Ports

These are shielded RJ-45 data sockets. They cannot

be used as standard traditional telephone sockets,

or to connect the unit to a traditional PBX or public

telephone network. Only connect RJ-45 data

connectors, network telephony systems, or network

telephones to these sockets. Either shielded or

unshielded data cables with shielded or unshielded

jackets can be connected to these data sockets.

AVERTISSEMENT : Points d’accès RJ-45

Prises RJ-45 blindées. Ces prises ne peuvent servir

comme prises téléphone standard et ne permettent

pas la connexion de l’appareil à un système PBX ni à

un réseau téléphonique public. N’y branchez que

des prises RJ-45 mâles adaptées, ou des systèmes de

réseaux téléphoniques. Il est possible d’y brancher

des câbles blindés ou non comportant des prises de

type Jack (blindées ou non).

1

POSITIONING YOUR SWITCH

Safety Information

WARNING: Please read the ‘Important Safety Information’ section in the

Support and Safety Information sheet before you start.

VORSICHT: Bitte lesen Sie den Abschnitt ‘Wichtige Sicherheitsinformationen’

sorgfältig durch, bevor Sie das Gerät einschalten.

AVERTISSEMENT: Veuillez lire attentivement la section «Consignes

importantes de sécurité» avant de mettre en route.

When positioning your Switch, ensure:

●

It is out of direct sunlight and away from sources of heat.

●

Cabling is away from power lines, fluorescent lighting fixtures, and sources

of electrical noise such as radios, transmitters and broadband amplifiers.

●

Water or moisture cannot enter the case of the unit.

●

Air flow around the unit and through the vents in the side of the case is

not restricted. We recommend you provide a minimum of 25mm (1in.)

clearance.

Using the Rubber Feet

Use the four self-adhesive rubber feet to prevent your Switch from moving

around on your desk or when stacking with other flat top OfficeConnect

units. Only stick the feet to the marked areas at each corner of the underside

of your Switch.

Using a Stacking Clip

Use a stacking clip when stacking your Switch with curved OfficeConnect

units. Stacking clips are only supplied with curved OfficeConnect units. The

stacking clip allows you to stack units neatly and securely. Refer to user guide

of the curved unit for more details on how to use the stacking clip.

4

5

VORSICHT: RJ-45-Porte

RJ-45-Portes. Diese Portes sind geschützte

Datensteckdosen. Sie dürfen weder wie normale

traditionelle Telefonsteckdosen noch für die

Verbindung der Einheit mit einem traditionellenm

privatenm oder öffentlichenm Telefonnetzwerk

gebraucht werden. Nur RJ-45-Datenansclußhlüsse,

Telefonnetzsysteme oder Netztelefone an diese

Steckdosen anschließen. Entweder geschützte oder

ungeschützte Buchsen dürfen an diese

Datensteckdosen angeschlossen werden.

Wall Mounting

There are two slots on the underside of the OfficeConnect Switch that can be

used for wall mounting. 3Com recommends that you mount the Switch with

the LEDs facing upwards to prevent dust entering the ports.

When wall mounting the unit, ensure that it is within reach of the power

outlet.

You need two suitable screws. Ensure that the wall you are going to use is

smooth, flat, dry and sturdy. Make two screw holes which are 150mm (5.9in.)

apart. Fix the screws into the wall, leaving their heads 3mm (0.12in.) clear of

the wall surface.

Remove any connections to the Switch and locate it over the screw heads.

When in line, gently push the Switch on to the wall and move it downwards

to secure. When making connections, be careful not to push the Switch up

and off the wall.

CAUTION: Only wall mount single units, do not wall mount stacked

units.

Also available from 3Com, is the OfficeConnect Mounting Unit (part

number 3C16765). This allows you to firmly secure a stack of

OfficeConnect devices to the desktop or onto a shelf in a rack.

Document Information: Manufacturer: 3Com Product Name/ID: OfficeConnect 3C16793 / #573 Category: Switch Document Type: Specifications File Path: 3com/officeconnect-3c16793_573.pdf Last Updated: 08 May 2023 Pages: 2
Pages Preview:

Note for Owners:

Guidesimo.com webproject is not a service center of 3Com trademark and does not carries out works for diagnosis and repair of faulty 3Com OfficeConnect 3C16793 equipment. For quality services, please contact an official service center of 3Com company. On our website you can read and download documentation for your 3Com OfficeConnect 3C16793 device for free and familiarize yourself with the technical specifications of device.

More Switch Devices:

Recommended Documentation:

3Com Manuals and Guides:

The main types of 3Com OfficeConnect 3C16793 instructions: user guide — rules of useing and characteristics, service manual — repair, diagnostics, maintenance, operation manual — description of the main functions of 3Com OfficeConnect 3C16793 equipment, etc.

Most of the instructions, that you can see on the site are uploaded by our users. If you have available a manual or document for 3Com OfficeConnect 3C16793, which is currently not on the site or present in a different language version, we ask you to upload your document on website, using the «uploading form» available to all registered users.