6d16 двигатель руководство по ремонту

• 39, CAT 6D16 11-16 Rocker and Bracket Assembly ● Disassembly sequence 1 Rocker assembly 2 Rocker bushing 3 Lock nut 4 Adjusting screw 5 Rocker 6 No. 6 rocker shaft bracket 7 Set screw 8 No. 5 rocker shaft bracket 9 No. 4 rocker shaft bracket 10 No. 3 rocker shaft bracket 11 No. 2 rocker shaft bracket 12 No. 1 rocker shaft bracket 13 Rocker shaft spring 14 Rocker shaft ● Assembly sequence Reverse the order …

• 36, CAT 6D16 11-13 11 Service standards Unit: mm (in.) Tightening torques Unit: N·m (kgf·m) [lbf·ft] Lubricant Special tools ◆ Service procedure Cylinder head and valve assembly [Removal] • Before loosening the cylinder head bolts 8, loosen the adjusting screw C on every rocker A that is compressing its valve spring B. 10 Location Maintenance item Standard value Limi…

• 14, CAT 6D16 Put alignment marks on part combinations before disassembly and arrange the disassembled parts neatly. This will help avoid mismating of the parts later. Put the alignment marks, punch marks, etc. where performance and appearance will not be affected. Cover the area left open after removal of parts to keep it free from dust. CAUTION • Take care to avoid mixing up numerous parts, similar part…

• 8, Terms and Units The terms and units in this manual are defined as follows. ● This service manual contains important cautionary instructions and supplementary information under the following four headings which identify the nature of the instructions and information: DANGER WARNING CAUTION NOTE ● Front and rear The terms “front” is the fan side and “rear” the flywheels side of the engin…

• 21, • Use specified bolts and nuts and tighten them at specified torques according to the following table, unless otherwise specified. • Threads and contact seats shall be dry. • Where there is a difference in strength classification between the nut and bolt (or stud bolt), the torque specified for the bolt shall apply. Hex-head Bolt and Stud Bolt Unit: N·m …

• 30, 11-6 TROUBLESHOOTING Incorrect oil viscosity Gr 11 Incorrect/defective fuel Gr 13 Incorrect valve clearance Defective cylinder head gasket Worn valve/valve seat, and carbon deposits Weakened valve spring Worn/damaged piston ring(s) Worn/damaged piston ring groove(s) Incorrect injection timing Gr 13 Defective injection pump Gr 13 Defective cooling system Gr 14 Defective injection nozzle(s…

• 33, 11-10 2. Inspecting and Adjusting Valve Clearances Service standards Unit: mm (in.) Tightening torques Unit: N·m (kgf·m) [lbf·ft] Valve clearances should be checked and adjusted when the engine is cold. [Inspection] • Bring piston No. 1 or piston No. 6 to the top-dead-centre (TDC) position of its compression stroke. To do this, crank the engine until the “1.6” mark …

• 13, Be particularly careful not to work in shoes that have oily soles and are slippery. When working as a team of two or more, arrange signals in advance and keep confirming safety. Be careful not to accidentally bump switches or levers. Check for oil leakage before cleaning the area having the fault otherwise you might miss detecting the leakage. Prepare replace…

• 22, Hex-head Flange Bolt Unit: N·m (kgf·m) [lbf·ft] 00-13 00 Strength 4T 7T 8T classification 4 to 6 8 to 12 9 to 14 M6 (0.4 to 0.6) – (0.8 to 1.2) – (0.9 to 1.4) – [2.95 to 4.43] [5.90 to 8.85] [6.64 to 10.3] 10 to 15 19 to 28 22 to 32 M8 (1.0 to 1.5) – (1.9 to 2.8) – (2.2 to 3.3) – [7.38 to 11.1] [14.0 to 20.6] [16.2 to 23.6] 21 to 30 20 to 28 …

• 35, 11-12 ● Assembly sequence Follow the disassembly sequence in reverse. CYLINDER HEAD AND VALVE MECHANISM 04134 ● Disassembly sequence 1 Joint 2 Oil filler cap 3 Bolt 4 Plate 5 Rubber 6 Rocker cover gasket 7 Rocker cover 8 Cylinder head bolt 9 Rocker and bracket assembly P.11-16 10 Cylinder head and valve assembly P.11-20 11 Cylinder head gasket 12 Push rod 13 Tappet * : Crankcase P.1…

• 15, Take care when handling sensors, relays, etc. which are vulnerable to shock and heat. Do not attempt to remove the cover from, or apply paint to, the electronic control unit. Pull the connector, and not the harness lead, to separate connectors. To separate a lock-type connector, first push toward arrow mark. To reconnect a lock-type connector, press the separate…

• Ref. 5124405AFR MANUEL D’UTILISATIONEN USER’S MANUALPL INSTRUKCJA OBSŁUGIRU РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИCS UŽIVATELSKÁ PŘÍRUČKAES MANUAL DE USOIT MANUALE D’USOEL ΕΓΧΕΙΡΙΔΙΟ ΧΡΗΣΗΣTR KULLANICI KILAVUZUFA AR ELIXO 500 230 V RTSELIXO 800 230 V RTSSliding Gate Openerwww.somfy.com …

  Elixo 500 230 V 48

• OPERATOR’S MANUAL FZ70S Fig.1 Front Nut Rear nut FEATURES The FZ70S is the most powerful 4 cycle engine of its size and was de-veloped for sport flying as well as power demanding acrobatics. • Supercharged system • Fuel injected • Regulated and pressurized fuel system • Muffler The pressurized fuel and injection system makes throttle response supe-r …

  FZ70S 4

• Φ32.0mm 26.0mm 20.9cc15”x8“~16”x6”・Filterwithweight[G36-154] ・DurabletubeforGasoline(1m)[G36-155] ・Aluminumspinnernut[100-30]・Tappetadjustingkit[30-161] ・Digitaltachometer[G17-167]Bore Body:690g/Muffler:83g/Ignitionsystem:100g/Enginemount:156gStroke Disp. …

  FG-21 2

1. Двигатели Mitsubishi 6D14, 6D14-T, 6D15-T, 6D16, 6D17 / Hyundai D6BR: Устройство, техническое обслуживание и ремонт

   

   Издательство: Легион-Автодата
   Жанр: Устройство и системы автомобиля

   Качество: Хорошее
   Страниц: 248
   Формат: pdf, fb2, epub

   В руководстве дается подробное пошаговое описание процедур по ремонту и техническому обслуживанию дизельных двигателей Mitsubishi серии 6D14 (6557 см3), 6D14-T (6557 см3), 6D15-T (6919 см3), 6D16 (7545 см3), 6D17 (8201 см3), и двигателей Hyundai серии D6BR (7545 см3). Издание содержит подробные сведения по ремонту и регулировке механизмов двигателя, системы смазки, охлаждения, топливной системы, системы турбонаддува и системы электрооборудования двигателя. Подробно рассмотрены настройки и регулировки различных ТНВД и регуляторов (RSV, RFD, R901, R801, RLD-J, включая регулятор RED-III с электронным управлением), форсунок, системы поддержания скорости, системы горного тормоза, моторного тормоза (Powertardo и Jake Brake), инерционного наддува. Приведены инструкции по использованию системы самодиагностики ТНВД с электронным управлением (RED-III), системы поддержания скорости, электросхемы систем с электронным управлением. Руководство содержит возможные неисправности и методы их устранения, сопрягаемые размеры основных деталей и пределы их допустимого износа, рекомендуемые смазочные материалы и рабочие жидкости. Книга предназначена для автовладельцев, персонала СТО и ремонтных мастерских.

   Вложения:

Только оригинальные руководства

Доступно сразу после оплаты

Полное соответствие бумажным изданиям

100% защита ваших оплат

О руководстве

Тип двигателя: Caterpillar 6D16

В руководстве вы найдете

• Пошаговое руководство по ремонту различных узлов и агрегатов
• Инструкцию по самостоятельному уходу и обслуживанию
• Сведения о конструкции двигателя и о том как предупредить неисправность
• Информацию для поездки на СТО, если самостоятельный ремонт невозможен

Написать отзыв

Ваше Имя:

Ваш отзыв:

Оценка:

Tolle Motorreparaturanleitung! Ich konnte alles selbst und ohne Probleme machen.