CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN.00
MANY1032A.EN.00
Airmaster Q1 hardware Installation Guide
Version 1.0
SAFETY WARNING
Do not operate the Airmaster Q1 until you and all personnel concerned have read
and understood this installation guide. Failure to follow instructions could result
in death or serious injury.
Important notes
This document serves as installation guide for all Airmaster Q1 products of CMC NV.
Installation and startup may only be done by trained personnel according to safe
engineering practices and with the observance of all relevant local health and safety
requirements and regulations.
A requirement of fault-free operation and fulfillment of any rights to claim under
guarantee is that the documentation is observed. In case of doubt please contact CMC.
This document could be subject to changes. Please contact our factory in case of doubt
in order to ensure that you have received the latest version.
The Airmaster Q1 is further referred to as the «controller».
This document serves as a manual for the installation of the controller. Remark that the
controller always acts as a component of a complete system in which it is integrated. As
such other documentation for the installation related to the integration of the controller in
the complete system will have to be consulted as well. Reference to such other
documentation is not possible from within the scope of this document. Regardless of the
content of any other documentation, the content of this documentation needs to be fully
respected.
CMC NV, Industriezone Klein Frankrijk, Klein Frankrijkstraat 40, 9600 Ronse, Belgium
Многофункциональный промышленный электронный блок управления (контроллер AirMaster Q1) — предназначен для управления воздушными винтовыми компрессорами.
Контроллер выполнен в корпусе из алюминиевого сплава с антикоррозионным покрытием и полиэтиленовой клавиатурой. Степень защиты — IP65 для фронтальных элементов, IP20 для остальных. Температура эксплуатации от 0 до +55°С при относительной влажности до 95% (без конденсации), температура хранения от -25 до +75°С. Коммутация входных и выходных сигналов осуществляется через контактные разъемы. Питание контроллера – разъем Х01 — осуществляется от сети 24VAC ± 15% частотой 50…60 Гц, максимальный потребляемый ток 1А. Отображение информации осуществляется с помощью жидкокристаллического дисплея 45 х 25мм с подсветкой
Скачать инструкцию Airmaster Q1
Скачать параметры Airmaster Q1
- Manuals
- Brands
- CMC Manuals
- Controller
- Airmaster Q1
Manuals and User Guides for CMC Airmaster Q1. We have 1 CMC Airmaster Q1 manual available for free PDF download: Hardware Installation Manual
CMC Manuals and Guides:
The main types of CMC Airmaster Q1 instructions: user guide — rules of useing and characteristics, service manual — repair, diagnostics, maintenance, operation manual — description of the main functions of CMC Airmaster Q1 equipment, etc.
Most of the instructions, that you can see on the site are uploaded by our users. If you have available a manual or document for CMC Airmaster Q1, which is currently not on the site or present in a different language version, we ask you to upload your document on website, using the «uploading form» available to all registered users.
|
Detail Specifications: 1456/1456482-airmaster_q1.pdf file (27 Feb 2023) |
Accompanying Data:
CMC Airmaster Q1 Controller PDF Hardware Installation Manual (Updated: Monday 27th of February 2023 12:30:40 AM)
Rating: 4.1 (rated by 14 users)
Compatible devices: CONTROLLER INTERFACE, Trident, MAXinBOX Hospitality ZCL-HP126, Airmaster R1, Pana40 Plus 3D, BD306, DIN-A-MITE A, Lyric LCP500-LC.
Recommended Documentation:
Text Version of Hardware Installation Manual
(Ocr-Read Summary of Contents, UPD: 27 February 2023)
-
17, CMC Airmaster Q1 CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 16 Section 4.10 3-Phase monitoring inputs In operation, high lethal voltages apply on these connections. Assure all power is switched off at the moment of installation. Never assume power is off but always check the circuit. The signals applied to the 3-Phase monitoring in…
-
1, CMC Airmaster Q1 CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN.00 CMC NV, Industriezone Klein Frankrijk, Klein Frankrijkstraat 40, 9600 Ronse, Belgium MANY1032A.EN.00 Airmaster Q1 hardware Installation Guide Version 1.0 SAFETY WARNING Do not operate the Airmaster Q1 until you and all personnel concerned have read and understood …
-
3, CMC Airmaster Q1 CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 2 Limit of Liability The publisher and the author make no representation or warranties with respect to the accuracy or completeness of the contents of this work and specifically disclaim all warranties, including without limitation warranties of fitness for a particular purpose. No warranty may be cr…
-
13, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 12 In X15 or X16 it is possible that one optional analog input is available. Such input can be recognized by having 3 connection pins in its connector. If a connector with 2 connection pins is installed, it is a RS485 connector (see further). Note: on these 3 pin connectors a GND conn…
-
4, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 3 Installation guide Table of Contents Section 1: Situation of the product …………………………………………………………………………………………………………………………. 4 Section 2: Safety ……………………………………………..…
-
12, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 11 Three fixed analog inputs are available. All three have 2 dedicated connections: Analog input 1: Connections C-ANA1 and AN1 current input: 4 .. 20 mA Analog input 2: Connections C-ANA2 and AN2 current input: 4 .. 20 mA Analog input 3: Connections C-ANA3 and AN3 Selectable by softw…
-
2, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN.00 Page 1 Illustration of Airmaster Q1. Remark the layout of the front panel can be different from the above picture.
… -
9, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 8 Section 4: Connections and Protection Remarks: It remains the responsibility of the integrator of this controller (being a component in the total system) to assure that the integration of the controller (in terms of wiring and use of other components) is done according to all applicable regulatio…
-
15, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 14 Such input can be recognized by having 2 connection pins in its connector. If a connector with 3 connection pins is installed, it is an analog input connector (see above). In case such optional connection(s) are installed, these connection(s) shall only be used for conne…
-
5, CMC NV – Airmaster Q1 Installation Guide – V1.0 – MANY1032A.EN Page 4 Section 1: Situation of the product The controller is an industrial controller. This hardware installation guide is a guide for the hardware related items. Refer to the software specifications file for information on how to work with the unit. The application area is restricted to compon…
Recommended Instructions:
C-383, KX-UT248, TG1847.0.EC.750, Zarauz Con Deluxe, Verona
-
1/4NTR 775 A03 — 200688 970 1171500 0327RIESGO DE EXPLOSION- Segun CSA C22.2 No 213: Este aparato esta preparado para trabajar dentro de ambientes peligrosos de classe I, Division 2, grupos A, B, C, y D o unicamente en lugares no peligrosos. Reemplazar componentes puede perjudicar la adecuación para la clase I, división 2.- Asegúrese de que la tensión de alimentació …
88 970 117 2
-
800A800FR-A860 (600V CLASS SPECIFICATION INVERTER)INSTRUCTION MANUAL (STARTUP)FR-A860-00027-00450-N6FR-A860-00680-04420Thank you for choosing this Mitsubishi Electric Inverter.This Instruction Manual and the enclosed CD-ROM give handling information and precautions for use of thisproduct.Do not use this product until you have a full knowledge of the equipment, safety information and instruction …
800 Series 25
-
# Installation Instructions 86129 │ Ignition Controller 210MN Kit (rev 3H) Revision Date: Oct. 23, 2019 S:NTI2001_N_Drive (1-20-09)R&DPARTS — ENGINEERINGParts Department Stickers and InstructionsCurrent Parts Instructions (doc)Parts instructions word docs86129 instructions – Ignition Controller 210MN Kit (rev 3H).doc NTI Boilers Inc …
86129 3
-
Kieback&Peter GmbH & Co. KGTempelhofer Weg 50, 12347 Berlin/GermanyTelefon: +49 30 60095-0, Telefax: +49 30 60095-164www.kieback-peter.de, [email protected], MD15-HR, MD15-DA3.09-20.115-01-EN | 2019-08-12QProduct DescriptionMD15-C, MD15-HR and MD15-DA ActuatorsFor Rxx, RWxx valves and Danfoss RA Series ApplicationThe MD15-C, MD15-HR and MD15-DA actuators for three-p …
MD15-HR 14