-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
Atlas Copco Instruction Manual
Instruction Manual
for Portable Compressors
English
XAS 97 DD — XAS 185 DD7
Engine Deutz D2011L03
Engine Deutz F3M2011
Related Manuals for Atlas Copco XAS 97 DD
Summary of Contents for Atlas Copco XAS 97 DD
-
Page 1
Atlas Copco Instruction Manual Instruction Manual for Portable Compressors English Engine Deutz D2011L03 XAS 97 DD — XAS 185 DD7 Engine Deutz F3M2011… -
Page 3
Instruction Manual for Portable Compressors XAS 97 DD — XAS 185 DD7 Printed matter N° 9829 3095 00 ATLAS COPCO — PORTABLE AIR DIVISION www.atlascopco.com 11/2008… -
Page 4
The manufacturer does not accept any liability for any damage arising for modifications, additions or conversions made without the manufacturer’s approval in writing. While every effort has been made to ensure that the information in this manual is correct, Atlas Copco does not assume responsibility for possible errors. -
Page 5: Table Of Contents
Preface Table of contents Starting / Stopping ……..32 Before starting……….32 Please read the following instructions carefully before starting to use your compressor. 4.3.1 Starting procedures …….. 32 Safety precautions ……..5 4.3.2 During operation ……..34 Introduction ……….5 It is a solid, safe and reliable machine, built 4.3.3 Stopping procedure ……..
-
Page 6
Adjustments and servicing procedures .. 45 Disposal …………. 63 Adjustment of the continuous 11.1 General …………63 regulating system……..45 11.2 Disposal of materials……..63 Air filter engine/compressor……. 46 Maintenance Log ……..64 6.2.1 Main parts ……….46 6.2.2 Cleaning the dust trap ……46 6.2.3 Replacing the air filter element …. -
Page 7: Safety Precautions
To be read attentively and acted accordingly before towing, lifting, operating, performing maintenance or repairing the compressor. INTRODUCTION The policy of Atlas Copco is to provide the users of It is the responsibility of management to appoint Take necessary steps to keep unauthorized persons…
-
Page 8: General Safety Precautions
GENERAL SAFETY PRECAUTIONS The manufacturer does not accept any liability for any Care shall be taken to avoid damage to safety damage arising from the use of non-original parts and valves other pressure-relief devices, The owner is responsible for maintaining the unit for modifications, additions or conversions made especially to avoid plugging by paint, oil coke or in a safe operating condition.
-
Page 9: Safety During Transport And Installation
13 If the warning light on the ABS module or in the Place the unit on level ground and apply the bends in lifting cables, chains or ropes. vehicle lights up, please contact Atlas Copco. parking brake before disconnecting the unit from Helicopter lifting is not allowed.
-
Page 10
13 Never refill fuel while the unit is running, unless The air line end connected to the outlet valve relatively short times, about the need to wear otherwise stated in the Atlas Copco Instruction must be safeguarded with a safety cable, attached ear protectors, Book (AIB). -
Page 11: Safety During Maintenance And Repair
(check valves) to isolate recommended or approved by Atlas Copco or the pressure systems. In addition, a warning sign machine manufacturer. Ascertain that the bearing a legend such as ”work in progress; do selected lubricants comply with all applicable not open”…
-
Page 12: Tool Applications Safety
15 Protect the engine, alternator, air intake filter, 23 Make sure that oil, solvents and other substances electrical and regulating components, etc., to likely to pollute the environment are properly prevent moisture ingress, e.g. when steam- disposed of. cleaning. 24 Before clearing the unit for use after maintenance 16 When performing any operation involving heat, or overhaul, check that operating pressures, flames or sparks on a machine, the surrounding…
-
Page 13: Specific Safety Precautions
If the set pressure must be altered then use only When batteries are being charged, an explosive correct parts supplied by Atlas Copco and in — the minimum working temperature Tmin in °C gas mixture forms in the cells and might escape (°F),…
-
Page 14: Leading Particulars
Injected oil is used for sealing, cooling and lubricating purposes. Compressor oil system The oil is boosted by air pressure. The system has no The compressors type XAS 97 DD — XAS 185 DD7 oil pump. silenced, single-stage, oil-injected…
-
Page 15
Regulation Frame and axles Data plate The compressor is provided with a continuous The compressor/engine unit is supported by rubber regulating system and a blow-down valve which is buffers in the frame. The standard unit has a none integrated in the unloader assembly. The valve is adjustable towbar with support leg and one of the closed during operation by outlet pressure of the following towing eyes AC, DIN, ball, ITA, GB or… -
Page 16: Main Parts
Main Parts (EP) (OFe) (TB) (AFD) (VI) (AR) (RV) (SV) (FP) (OLG) (DPec) (FCeo) (FCft) (AOV) (DSe) (CP) (FU) (OFce) (FF) (CE) (DPft) (FT) (AF) (VV) — 14 -…
-
Page 17
Reference Name Reference Name Alternator Hood Air Filter OFce Oil Filter (compressor element) Anti-Frost Device (option) Oil Filter (engine) Air Outlet Valves Oil Level Gauge (compressor element) Air Receiver Regulating Valve Coupling Starting Motor Compressor Element Safety Valve Control Panel Towbar Data Plate Vacuum Indicator… -
Page 18: Compressor Regulating System
COMPRESSOR REGULATING SYSTEM OVERVIEW (AF) (VI) (SC) (VV) (RV) (PG) (FR) (SV) (SR) (BOV) (OCce) (UV) (UA) (VH) (OS) (BDV) (CV) (OF) (AR) (SL) (AOV) (CE) (TS) (FP) (DP) (SL) (OLG) (FN) (DP) (DP) — 16 -…
-
Page 19
Reference Name Reference Name Air Filter Pressure Gauge Air Outlet Valves Regulating Valve Air Receiver Safety Cartridge (option) Blow Down Valve Scavenge Line Blow Off Valve Speed Regulator Compressor Element Safety Valve Check Valve Temperature Switch Drain Plug Unloader Assembly Engine Unloader Valve Vent Hole… -
Page 20: Air Flow
AIR FLOW Air drawn through the airfilter (AF) into the compressor element (CE) is compressed. At the element outlet, compressed air and oil pass into the air (AF) receiver/oil separator (AR/OS). The check valve (CV) prevents blow-back of compressed air when the compressor is stopped. In the air receiver/oil separator (AR/OS), most of the oil is removed from the air/oil mixture;…
-
Page 21: Oil System
OIL SYSTEM The lower part of the air receiver (AR) serves as oil tank. Air pressure forces the oil from the air receiver/oil separator (AR/OS) through the oil cooler (OCce) and oil filter (OF) to the compressor element (CE). When the compressor is stopped and / or there is no pressure in the system, the oil stop valve (OSV) prevents the oil from flowing back into the compressor element.
-
Page 22: Continuous Regulating System
CONTINUOUS REGULATING SYSTEM (RV) (SR) (UV) (UA) (VH) (AR) (CE) — 20 -…
-
Page 23
The compressor is provided with a continuous If the air consumption is less than the maximum air regulating system. This system is provided with a output, the regulating valve supplies control air to blow-down valve which is integrated in the unloader unloader valve (UV) to reduce the air output and assembly (UA). -
Page 24: Electric System
ELECTRIC SYSTEM Circuit diagram (standard) (9822 0797 01) The compressor is equipped with a negative earthed system. 12V DC 14« 15« 13« 8« 5« 7« D- D+ 6« 1« Auxiliary 2« 12« 3« Temp General 4« alarm (Lamp- tester) 9´,10´,11´ — 22 -…
-
Page 25
Reference Name Circuit Breaker (10 A) Alternator Battery Temperature Alarm Lamp General Alarm Lamp Starter Solenoid (part of M1) Shut-down Relay Blocking Relay Override Start Relay Start Relay Starter Motor Hourmeter Contact Switch (Off-On- Override-start) Temperature Switch Engine Oil Pressure Switch Engine Lamptest Switch Temperature Switch Compressor Fuel Solenoid Valve… -
Page 26
Circuit diagram cold start (9822 0864 00) 12V DC Auxiliary Temp General alarm (Lamptester) — 24 -… -
Page 27
Reference Name Circuit Breaker (10 A) Alternator Battery Temperature Alarm Lamp General Alarm Lamp Starter Solenoid (part of M1) Starter Motor Hourmeter Glowplug Contact Switch (Off-On- Override-start) Temperature Switch Engine Oil Pressure Switch Engine Lamptest Switch Temperature Switch Compressor Push Button Glowplug Fuel Solenoid Valve Diode Diode… -
Page 28
Operation of the electric circuit in detail Start switch S1 position 2: Engine is running normally: Line 3 on 12V (overwrite function) hourmeter P1 and Oil pressure contact S3 opens, K3 no longer excited. (K2) (K1) fuel solenoid Y1 excited. Thermocontact engine S2 K3 changes over (13-11), engine cuts out because fuel normally closed, oil pressure contact S3 open. -
Page 29: Markings And Information Labels
Start-Stop indication of switch. Compressor loaded. Do not run the compressor with open Electrocution hazard. Runlamp. doors. Atlas Copco mineral compressor oil. Airfilter. Lifting device. Atlas Copco synthetic compressor oil. Compressor temperature too high. Use diesel fuel only. 3.7 bar Atlas Copco mineral engine oil.
-
Page 30: Operating Instructions
Operating instructions PARKING INSTRUCTIONS PARKING, TOWING AND LIFTING INSTRUCTIONS Safety precautions The operator is expected to apply all relevant Safety precautions. Attention Before putting the compressor in to use, check the brake system as described in section Brake shoe adjustment. After the first 100 km travel: Non-adjustable towbar with standard support leg without (A) Parking position of jockey wheel (adjustable towbar)
-
Page 31: Towing Instructions
TOWING INSTRUCTIONS Label on towbar, towing instructions Non-adjustable towbar with standard support leg without Adjustable towbar with jockey wheel and brakes brakes For both non-adjustable — and adjustable towbar, the Before towing the compressor, ensure towbar should be as level as possible and the that the towing equipment of the vehicle compressor and towing eye end in a level position.
-
Page 32: Spillage-Free Instruction
SPILLAGE-FREE INSTRUCTION HEIGHT ADJUSTMENT (with adjustable towbar) • Remove spring pin (1). This compressor is fitted with a leak-proof undercarriage in order to protect the environment. • Release locking nut (2) by hand. Any leaking fluid is collected in case of malfunctions. •…
-
Page 33: Lifting Instructions
LIFTING INSTRUCTIONS ANTI-FROST DEVICE (OPTION) When lifting the compressor, the hoist has to be The anti-frost device consist of a manualy operated placed in such a way that the compressor, which must by-pass valve (1) on the oil cooler to prevent freezing be placed level, will be lifted vertically.
-
Page 34: Starting / Stopping
STARTING / STOPPING STARTING PROCEDURES BEFORE STARTING 1. Before initial start-up, prepare battery for operation if not already done. See section Recharging a battery. 2. With the compressor standing level, check the level of the engine oil. Add oil, if necessary, to the upper mark on dipstick.
-
Page 35
Starting procedure The control panel indicates receiver pressure (PG) accumulated operating hours (P1). Before starting open the air outlet valve(s) (see section Compressor regulating system, AOV) and push circuit breaker button (F1) once (open hood first). Circuit breaker button should now be in position B. -
Page 36: During Operation
DURING OPERATION STOPPING PROCEDURE FAULT SITUATIONS AND PROTECTIVE DEVICES When the engine is running, the air • A fault which occurs with the engine, either: oil outlet valves (ball valves) must always be pressure (too low), oil temperature (too high) or put in a fully opened or fully closed alternator voltage (too low) will always and position.
-
Page 37: Maintenance
For engine maintenance refer to Engine Operation Manual. Maintenance schedule Daily 50 hours after initial Yearly or every start-up 500 hours Service pak XAS 97 DD — XAS 185 DD7 2912 4393 06 Engine oil level Check Compressor oil level Check Fuel level Check/Fill…
-
Page 38
Maintenance schedule Daily 50 hours after initial Yearly or every (continuation of page 35) start-up 500 hours Oil coolers Clean Engine minimum and maximum speeds Check Check Torque of wheel nuts Check Check Brake system (if installed) Check/Adjust Check/Adjust Safety valve Test Door hinges Grease… -
Page 39
(continuation of page 36) Notes 1. More frequently when operating in a dusty environment. Keep the bolts of the housing, the lifting eye, the towbar and the axle securely 2. Replace the element after 1000 running hours or when the pressure drop exceeds 0.8 bar (11.6 psi). tightened. -
Page 40: Lubrication Oils
-5°C (23°F) and -20°C (-4°F) PAROIL S PAROIL 5W40 PAROIL from Atlas Copco is the ONLY oil tested PAROIL releases excess heat efficiently, whilst and approved for use in all engines built into Atlas maintaining excellent bore-polish protection to limit Copco compressors and generators.
-
Page 41: Oil Specifications
OIL SPECIFICATIONS COMPRESSOR OIL Mineral compressor oil PAROIL M Liter US gal Order number Never mix synthetic with mineral oil. 1615 5947 00 Remark: 1615 5948 00 When changing from mineral synthetic oil (or the other way around), barrel 55.2 1615 5949 00 you will need to do an extra rinse: After…
-
Page 42: Oil Level Check
OIL LEVEL CHECK CHECK COMPRESSOR OIL LEVEL Never mix oils of different brands or types. Use only non-toxic oils where there is a risk of inhaling delivered air. CHECK ENGINE OIL LEVEL Also consult the Engine Operation Manual for the oil specifications, viscosity recommendations and oil change intervals.
-
Page 43: Oil And Oil Filter Change
(5). Screw out filler plug (2) and add oil until the pointer of the oil level gauge (4) again registers in the upper In this case, contact Atlas Copco. extremity of the green range. Reinstall and tighten the filler plug.
-
Page 44: Cleaning Coolers
CLEANING COOLERS CLEANING FUEL TANK Steam cleaning in combination with a cleansing agent Observe all relevant environmental and may be applied in order to remove also the dirt safety precautions. sticking to the cooler fins. To avoid damaging the coolers, angle Place an appropriate drain pan under the drainplug between jet and coolers should be (see chapter Main Parts, DPec) of the fuel tank.
-
Page 45: Battery Care
BATTERY CARE ACTIVATING A DRY-CHARGED BATTERY RECHARGING A BATTERY • Take out the battery. Before and after charging a battery, always check the Before handling batteries, read the electrolyte level in each cell; if required, top up with • Battery and electrolyte must be at equal relevant safety precautions and act distilled water only.
-
Page 46: Changing Tyres
When a compressor element is due for overhaul, it specific maintenance measure. needs to be done by Atlas Copco. This guarantees the It guarantees that all necessary parts are replaced at use of genuine parts and correct tools with care and When changing a tyre, please observe that the arrow the same time keeping down time to a minimum.
-
Page 47: Adjustments And Servicing Procedures
Adjustments and servicing procedures ADJUSTMENT OF THE CONTINUOUS REGULATING SYSTEM The working pressure is determined by the tension of the spring in the regulating valve (RV). This tension can be increased to raise the pressure and decreased to lower it by turning the adjusting wheel clockwise and anti-clockwise respectively.
-
Page 48: Air Filter Engine/Compressor
MAIN PARTS CLEANING THE DUST TRAP To remove dust from the dust trap pinch the vacuator The Atlas Copco air filters are specially valve (6) several times. designed for the application. The use of non-genuine air filters may lead to…
-
Page 49: Replacing The Air Filter Element
REPLACING THE AIR FILTER ELEMENT AIR RECEIVER SAFETY VALVE All adjustments or repairs are to be done by an authorized representative of the valve supplier. Following checks must be carried out on the safety valve (2): • a check of the opening of the lifting gear, twice a year.
-
Page 50: Fuel System
FUEL SYSTEM BRAKE ADJUSTMENT Before jacking up the compressor, connect it to a towing vehicle or attach a weight of minimum 50 kg (110 lb) to the towbar. BRAKE SHOE ADJUSTMENT Check the thickness of the brake lining. When the brake lining has been worn to a thickness of 1 mm (0.039 in) or less, the brake shoes have to be replaced.
-
Page 51: Test Procedure Of Brake Cable Adjustment
TEST PROCEDURE OF BRAKE CABLE BRAKE CABLE ADJUSTMENT ADJUSTMENT (3) (2) 2 — 3 teeth Hand brake lever downward — brake not operated 1. Brake cable 4. Main brake cable 2. Lock nut 5. Equalizer 1. Check if the towing eye rod of the overrun brake 3.
-
Page 52: Problem Solving
Problem solving It is assumed that the engine is in good condition and Alternator precautions that there is adequate fuel flow to the filter and 1. Never reverse the polarity of the battery or the injection equipment. alternator. 2. Never break any alternator or battery connections An electrical fault must be traced by an while the engine is running.
-
Page 53
Problem Possible faults Corrective actions 3. Temperature alarm lamp (H1) does not a. Lamp (H1) blown a. Replace lamp. light up when switching (S1) to ”I” b. See fault 1d. b. See 1d. and applying lamp test. 4. Starter motor (S) does not crank a. -
Page 54
Engine does not run at max. speed. d. Check the maximum speed, service the fuel filter. e. Oil separator element (OS) clogged. e. Have element removed and inspected by an Atlas Copco Service representative. 12. Working pressure rises during a. -
Page 55: Available Options
Available options Pressure vessel approval: Tool box: Single ASME Twin Undercarriage: Adjustable towbar with brakes Safety: Wheel chocks Fixed towbar with brakes Safety cartridge Support (without undercarriage) Spark arrestor Simplified bumper Safety chain CE/ASME Towing eyes: Loose ball coupling Hose reel Towbar support: Jockey wheel Inlet shutdown valve…
-
Page 56: Technical Specifications
Technical specifications TORQUE VALUES GENERAL TORQUE VALUES CRITICAL TORQUE VALUES The following tables list the recommended torques applied for general applications Assemblies Torque value (Nm / lbf.ft) at assembly of the compressor. Wheel nuts 80 (59) +10/-0 Bolts, axle/beams 80 (59) +/- 10 For hexagon screws and nuts with strength grade 8.8 Bolts, towbar/axle 80 (59) +/- 10…
-
Page 57: Settings Of Shutdown Switches And Safety Valves
SETTINGS OF SHUTDOWN SWITCHES AND SAFETY VALVES Designation XAS 97 DD — XAS 185 DD7 Engine oil pressure bar(e) 17.4 Engine oil temperature °C 127 — 133 °F 260 — 270 Compressor temperature °C 116 — 120 °F 241 — 248…
-
Page 58: Compressor / Engine Specifications
COMPRESSOR / ENGINE SPECIFICATIONS REFERENCE CONDITIONS Designation XAS 97 DD — XAS 185 DD7 Absolute inlet pressure bar(e) 14.5 Relative air humidity Air inlet temperature °C °F Nominal effective working pressure bar(e) The inlet conditions are specified at the air inlet grating outside the canopy.
-
Page 59: Limitations
LIMITATIONS Designation XAS 97 DD — XAS 185 DD7 Minimum effective receiver pressure bar(e) Maximum effective receiver pressure, compressor bar(e) unloaded Maximum ambient temperature no aftercooler °C at sea level °F with aftercooler °C °F Minimum starting temperature °C °F Minimum starting temperature, with coldstart equipment °C…
-
Page 60: Altitude Unit Performance Curve
ALTITUDE UNIT PERFORMANCE CURVE Max. allowable working pressure as a function altitude and ambient temperature. TEMPERATURE IN °F 5000 16 405 4000 13 124 4.0 bar(e) 58 psi 3000 9 843 5.0 bar(e) 73 psi 6.0 bar(e) 2000 6 562 87 psi 7.0 bar(e) 1000…
-
Page 61: Performance Data
PERFORMANCE DATA At reference conditions, if applicable, and at normal shaft speed, unless otherwise stated. Designation XAS 97 DD — XAS 185 DD7 Engine shaft speed, normal and maximum r/min 2750 Engine shaft speed, compressor unloaded r/min 1850 Free air delivery…
-
Page 62: Design Data
DESIGN DATA Compressor Designation Number of compression stages Engine Designation XAS 97 DD — XAS 185 DD7 Designation XAS 97 DD — XAS 185 DD7 Make Deutz Capacity of oil sump: Type D2011L03 — Initial fill F3M2011 US gal 2.25 Coolant — Refill (max.)
-
Page 63
Unit Unit dimensions Designation XAS 97 DD — XAS 185 DD7 without brakes towbar Capacity of compressor oil fixed adjustable system US gal Length 2827 Net capacity of air receiver 16.7 111.3 US gal Width 1410 1410 Capacity of fuel tank 55.5… -
Page 64: Dataplate
Dataplate Company code Model Unit serial number Working pressure Speed Engine power Manufacturing year — 62 -…
-
Page 65
(for example sand, sawdust) and dispose it according the applicable local disposal Your Atlas Copco compressor consists for the most regulations. Do not drain into the sewage system or part of metallic materials, that can be remelted in surface water. -
Page 66
Maintenance Log Compressor ………………Customer ………………..Serial number………………………………….Service hours Maintenance action Date By initials — 64 -… -
Page 68
www.atlascopco.com…
- Manuals
- Brands
- Atlas Copco Manuals
- Compressor
- XAS 97 DD
Manuals and User Guides for Atlas Copco XAS 97 DD. We have 1 Atlas Copco XAS 97 DD manual available for free PDF download: Instruction Manual
|
Detail Specifications: 1856/1856205-xas_97_dd.pdf file (12 Jan 2023) |
Accompanying Data:
Atlas Copco XAS 97 DD Compressor PDF Instruction Manual (Updated: Thursday 12th of January 2023 04:49:51 PM)
Rating: 4.5 (rated by 13 users)
Compatible devices: 4UFCY, Giga 75, MB2420, LF 2, 9600, Copeland Scroll Digital ZRD36KRE, 10728, GA15.
Recommended Documentation:
Text Version of Instruction Manual
(Ocr-Read Summary of Contents, UPD: 12 January 2023)
-
61, Atlas Copco XAS 97 DD — 59 — PERFORMANCE DATA At reference conditions, if applicable, and at normal shaft speed, unless otherwise stated. 1 ) Free Air Delivery (volume flow rate) is measured according to ISO 1217 ed.3 1996 annex D Tolerance: • +/- 5% 25 l/s (53 cfm) < FAD < 250 l/s (530 cfm) • +/- 4% 250 l/s (530 cfm) < FAD The international standard ISO 1217 corresponds to following national stand…
-
33, — 31 — LIFTING INSTRUCTIONS When lifting the compressor, the hoist has to be placed in such a way that the compressor, which must be placed level, will be lifted vertically. Keep lifting acceleration and retardation within safe limits. Preferably use the lifting eye (1) after opening the small door (2). ANTI-FROST DEVICE (OPTION) The anti-frost device consist of a manualy operated by-pas…
-
39, — 37 — (continuation of page 36) Notes 1. More frequently when operating in a dusty environment. 2. Replace the element after 1000 running hours or when the pressure drop exceeds 0.8 bar (11.6 psi). 3. Refer to the Deutz operation manual. 4. 500 hours only valid when using PAROIL SAE 15W40. 5. Also drain engine oil from engine oil cooler (see chapter Main Par…
-
59, — 57 — LIMITATIONS 1) For Hose Reel application: maximum ambient temperature 30°C 2) Cold start equipment not available at time of release. Designation XAS 97 DD — XAS 185 DD7 Minimum effective receiver pressure bar(e) 4 psi 58 Maximum effective receiver pressure, compressor unloaded bar(e) 9 psi 130 Maximum ambient temperature at sea level 1) no aftercoole…
-
45, — 43 — BATTERY CARE If the battery is still dry, it must be activated as described in section Activating a dry-charged battery. The battery must be in operation within 2 months from being activated; if not, it needs to be recharged first. ELECTROLYTE Electrolyte in batteries is a sulphuric acid solution in distilled water. The solution must be made up before being introduced into the ba…
-
10, — 8 — 4 Close the compressor air outlet valve before connecting or disconnecting a hose. Ascertain that a hose is fully depressurized before disconnecting it. Before blowing compressed air through a hose or air line, ensure that the open end is held securely, so that it cannot whip and cause injury. 5 The air line end connected to the outlet valve must be safeguarded with a safety cable, at…
-
8, — 6 — The manufacturer does not accept any liability for any damage arising from the use of non-original parts and for modifications, additions or conversions made without the manufacturer’s approval in writing. If any statement in this manual does not comply with local legislation, the stricter of the two shall be applied. Statements in these safety precautions should not …
-
41, — 39 — OIL SPECIFICATIONS Never mix synthetic with mineral oil. Remark: When changing from mineral to synthetic oil (or the other way around), you will need to do an extra rinse: After doing the complete change procedure to synthetic oil, run the unit for a few minutes to allow good and complete circulation of the synthetic oil. Then drain the synthetic oil again and f…
-
23, — 21 — The compressor is provided with a continuous regulating system. This system is provided with a blow-down valve which is integrated in the unloader assembly (UA). The valve is closed during operation by outlet pressure of the compressor element and opens by air receiver pressure when the compressor is stopped. When the air consumption increases, the air receiver pressure will decreas…
-
42, Atlas Copco XAS 97 DD — 40 — OIL LEVEL CHECK CHECK ENGINE OIL LEVEL Also consult the Engine Operation Manual for the oil specifications, viscosity recommendations and oil change intervals. For intervals, see Preventive maintenance schedule for the compressor. Check engine oil level according to the instructions in the Engine Operation Manual and if necessary top up with oil. CHECK COMPRESSOR OIL LEVEL With the u…
-
58, Atlas Copco XAS 97 DD — 56 — COMPRESSOR / ENGINE SPECIFICATIONS REFERENCE CONDITIONS The inlet conditions are specified at the air inlet grating outside the canopy. Designation XAS 97 DD — XAS 185 DD7 Absolute inlet pressure bar(e) 1 psi 14.5 Relative air humidity % — Air inlet temperature °C 20 °F 68 Nominal effective working pressure bar(e) 7 psi 102
…
Recommended Instructions:
Security TVMP-1600RM, 33ML8905, dlan 550 duo+, ICD-BX112
-
SHARK 25ITManuale d’istruzioniLista ricambi286-89LEGGERE ATTENTAMENTEENOperator’s manualSpare parts list886-89READCAREFULLYFRManuel d’instructionsListe pièce de rechange1486-89LIREATTENTIVEMENTDEBedienungsanleitungErsatzteilliste2086-89SORGFÄLTIGLESENESManual de instruccionesLista repuestos2686-89LEERATENTAMENTENLGebruikershandleidingOnderdelenlijst3286-89EERST G …
SHARK 25 88
-
Strut support upperPuntal de apoyosuperiorBinding screwTornillo de uniónBolt M12Tornillo M12Wing nut M12Mariposa M12Spring clasp bracketResorte de ganchoSpring clasp holderResorte sujetadorSpring claspGancho de resorteStrut support lowerSoporte de apoyoinferiorStrut shaft claspGancho de eje Bolt M10Perno M10BracketSoporte de montajeKnob / PerillaRoller shaftRodillo ejeSplit washer 12Arandel …
KN 7421 2
-
© Midmark Corporation 20061ClassicSeries™ Compressor InstallationApplies to Models:CL21- 115 VoltsCL22, CL32, CL52 — 208- 230 Volts10540700 Rev. O (11/11) Model CL32 ShownEquipment AlertCompressor system must be installed per local plumbing and electrical codes.Components Shown are Typical on allClassicSeries™ Compressor ModelsAA181101Electrical BoxHour MeterFresh Air IntakeC …
Classic Series 11
-
————-DE Originalbetriebsanleitung————-EN Translation of the original instructions————-FR Traduction du mode d’emploi d’origine————-IT Traduzione del Manuale d’Uso originale————-NL Vertaling van de originele gebruiksaanwijzing————-CZ Překlad originálního návodu k provozu————-SK Preklad originálneho návodu …
232/08/24 64
Popular Right Now:
Operating Impressions, Questions and Answers:
Table of Contents for Atlas Copco XAS 97 DD:
-
— 39 — OIL SPECIFICATIONS Never mix synthetic with mineral oil. Remark: When changing from mineral to synthetic oil (or the other way around), you will need to do an extra rinse: After doing the complete change procedure to synthetic oil, run the unit for a few minutes to allow good and complete circulation of the synthetic oil. Then drain the synthetic oil again and fill again with new synthetic oil. To set correct oil levels, proceed as in normal instruction. COMPRESSOR OIL Mineral compressor oil PAROIL M Synthetic compressor oil PAROIL S Mi
-
— 22 — ELECTRIC SYSTEM Circuit diagram (standard) (9822 0797 01) S1 3 2 1 0 q q 21 20 6 8 7 9 24 25 28 29 3 5 4 21 8« 7« 1« 2« 12 14 4« 3« 26 27 12« 34 35 9´,10´,11´ p 12V DC 5« Te mp K1 General alarm (Lamp- tester) 13« 15« 14« 11 10 13 11999 15 14 Auxiliary 33338 18 1615 4 3 2 1 3 2 1 0 32 33 31 30 5 10A 2322 19 17 6 7 6« D- D+ B+ + M M1 K0 S2 S3 G2 G1 K4
-
— 57 — LIMITATIONS 1) For Hose Reel application: maximum ambient temperature 30°C 2) Cold start equipment not available at time of release. Designation XAS 97 DD — XAS 185 DD7 Minimum effective receiver pressure bar(e) 4 psi 58 Maximum effective receiver pressure, compressor unloaded bar(e) 9 psi 130 Maximum ambient temperature at sea level 1) no aftercooler °C 45 °F 113 with aftercooler °C 40 °F 104 Minimum starting temperature °C -10 °F 14 Minimum starting temperature, with coldstart equipment 2) °C -20 °F -4 Altitu
-
— 6 — The manufacturer does not accept any liability for any damage arising from the use of non-original parts and for modifications, additions or conversions made without the manufacturer’s approval in writing. If any statement in this manual does not comply with local legislation, the stricter of the two shall be applied. Statements in these safety precautions should not be interpreted as suggestions, recommendations or inducements that it should be use
-
— 11 — SPECIFIC SAFETY PRECAUTIONS Batteries When servicing batteries, always wear protecting clothing and glasses. 1 The electrolyte in batteries is a sulphuric acid solution which is fatal if it hits your eyes, and which can cause burns if it contacts your skin. Therefore, be careful when handling batteries, e.g. when checking the charge condition. 2 Install a sign prohibiting fire, open flame and smoking at the post where batteries are being charged. 3 When batteries are being charged, an explosive gas mixture forms in the
-
— 3 — Preface Please read the following instructions carefully before starting to use your compressor. It is a solid, safe and reliable machine, built according to the latest technology. Follow the instructions in this booklet and we guarantee you years of troublefree operation. Always keep the manual available near the machine. In all correspondence always mention the compressor type and serial number, shown on the data plate. The company reserves the right to make changes without prior notice. Table of contents 1 Safety precautions ……………………….
-
— 35 — Maintenance USE OF SERVICE PAKS Service Paks include all genuine parts needed for normal maintenance of both compressor and engine. Service Paks minimize downtime and keep your maintenance budget low. Order Service Paks at your local Atlas Copco dealer. The schedule contains a summary of the maintenance instructions. Read the respective section before taking maintenance measures. When servicing, replace all disengaged packings, e.g. gaskets, O-rings, washers. For engine mainte
-
— 2 — Warranty and Liability Limitation Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability. The manufacturer does not accept any liability for any damage arising for modifications, additions or conversions made without the manufacturer’s approval in writing. While every effort has been made to ensure that the information in this manual is correct, Atlas Copco does not assume responsibility for possible errors. Copyright 2008, At
-
— 56 — COMPRESSOR / ENGINE SPECIFICATIONS REFERENCE CONDITIONS The inlet conditions are specified at the air inlet grating outside the canopy. Designation XAS 97 DD — XAS 185 DD7 Absolute inlet pressure bar(e) 1 psi 14.5 Relative air humidity % — Air inlet temperature °C 20 °F 68 Nominal effective working pressure bar(e) 7 psi 102
-
— 34 — DURING OPERATION Regularly carry out following checks: 1. That regulating valve (see section Main Parts, RV) is correctly adjusted, i.e. starts decreasing the engine speed when reaching the preset working pressure in the receiver. 2. Check the air filter vacuum indicators (see section Main Parts, VI). If the yellow piston reaches the red marked service range, replace the filter element. Reset the indicators by pushing the reset button. 3. On compressors
-
— 10 — 15 Protect the engine, alternator, air intake filter, electrical and regulating components, etc., to prevent moisture ingress, e.g. when steam- cleaning. 16 When performing any operation involving heat, flames or sparks on a machine, the surrounding components shall first be screened with non- flammable material. 17 Never use a light source with open flame for inspecting the interior of a machine. 18 Disconnect –battery-clamp before starting electrical servicing or wel
Questions, Opinions and Exploitation Impressions:
You can ask a question, express your opinion or share our experience of Atlas Copco XAS 97 DD device using right now.
Download or browse on-line these Instruction Manual for Atlas Copco XAS 97 DD Compressor.
Summary of Contents:
 |
[Page 1] Atlas Copco XAS 97 DD www.atlascopco.com Atlas Copco Instruction Manual Engine Deutz D2011L03 XAS 97 DD — XAS 185 DD7 Engine Deutz F3M2011 Instruction Manual for Portable Compressors English |
 |
[Page 2] Atlas Copco XAS 97 DD … |
 |
[Page 3] Atlas Copco XAS 97 DD ATLAS COPCO — PORTABLE AIR DIVISION www.atlascopco.com Printed matter N° 9829 3095 00 11/2008 Instruction Manual for Portable Compressors XAS 97 DD — XAS 185 DD7 |
 |
[Page 4] Atlas Copco XAS 97 DD — 2 — Warranty and Liability Limitation Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability. The manufacturer does not accept any liability for any damage arisin… |
 |
[Page 5] Atlas Copco XAS 97 DD — 3 — Preface Please read the following instructions carefully before starting to use your compressor. It is a solid, safe and reliable machine, built according to the latest technology. Follow the instructions in this booklet and we guarantee you ye… |
 |
[Page 6] Atlas Copco XAS 97 DD — 4 — 6 Adjustments and servicing procedures .. 45 6.1 Adjustment of the continuous regulating system…………………………………. 45 6.2 Air filter engine/compressor………………….. 46 6.2.1 Main parts …………………………. |
 |
[Page 7] Atlas Copco XAS 97 DD — 5 — Safety precautions INTRODUCTION The policy of Atlas Copco is to provide the users of their equipment with safe, reliable and efficient products. Factors taken into account are among others: — the intended and predictable future use of the produ… |
 |
[Page 8] Atlas Copco XAS 97 DD — 6 — The manufacturer does not accept any liability for any damage arising from the use of non-original parts and for modifications, additions or conversions made without the manufacturer’s approval in writing. If any statement in this manual does… |
 |
[Page 9] Atlas Copco XAS 97 DD — 7 — SAFETY DURING TRANSPORT AND INSTALLATION When towing, lifting or transporting the compressor in any way, the battery switch must always be in the “OFF” position! To lift a unit, all loose or pivoting parts, e.g. doors and towbar, shall fir… |
 |
[Page 10] Atlas Copco XAS 97 DD — 8 — 4 Close the compressor air outlet valve before connecting or disconnecting a hose. Ascertain that a hose is fully depressurized before disconnecting it. Before blowing compressed air through a hose or air line, ensure that the open end is held … |
 |
[Page 11] Atlas Copco XAS 97 DD — 9 — 22 When washing parts in or with a cleaning solvent, provide the required ventilation and use appropriate protection such as a breathing filter, safety glasses, rubber apron and gloves, etc. 23 Safety shoes should be compulsory in any workshop … |
 |
[Page 12] Atlas Copco XAS 97 DD — 10 — 15 Protect the engine, alternator, air intake filter, electrical and regulating components, etc., to prevent moisture ingress, e.g. when steam- cleaning. 16 When performing any operation involving heat, flames or sparks on a machine, the surro… |
 |
[Page 13] Atlas Copco XAS 97 DD — 11 — SPECIFIC SAFETY PRECAUTIONS Batteries When servicing batteries, always wear protecting clothing and glasses. 1 The electrolyte in batteries is a sulphuric acid solution which is fatal if it hits your eyes, and which can cause burns if it conta… |
 |
[Page 14] Atlas Copco XAS 97 DD — 12 — Leading particulars DESCRIPTION OF SAFETY PICTOGRAMS USED IN THIS MANUAL GENERAL DESCRIPTION The compressors type XAS 97 DD — XAS 185 DD7 are silenced, single-stage, oil-injected screw compressors, built for a nominal effective working pressu… |
 |
[Page 15] Atlas Copco XAS 97 DD — 13 — Regulation The compressor is provided with a continuous regulating system and a blow-down valve which is integrated in the unloader assembly. The valve is closed during operation by outlet pressure of the compressor element and opens by air re… |
 |
[Page 16] Atlas Copco XAS 97 DD — 14 — Main Parts (SV) (A) (VI) (AR) (RV) (FP) (OLG) (AOV) (CP) (C) (AF) (VV) (FF) (FU) (CE) (F) (EP) (FT) (D) (FCeo) (FCft) (DPec) (DSe) (OFe) (OFce) (TB) (H) (DPft) (S) (E) (AFD) |
 |
[Page 17] Atlas Copco XAS 97 DD — 15 — Reference Name A Alternator AF Air Filter AFD Anti-Frost Device (option) AOV Air Outlet Valves AR Air Receiver C Coupling CE Compressor Element CP Control Panel D Data Plate DPec Drain Plug Engine Oil Cooler DPft Drain Plug Fuel Tank DSe Engin… |
 |
[Page 18] Atlas Copco XAS 97 DD — 16 — COMPRESSOR REGULATING SYSTEM OVERVIEW (BOV) (AF) (DP) (FN) (UV) (UA) (VH) (BDV) (CV) (AOV) (RV) (SR) (VV) (VI) (SV) (FR) (PG) (AR) (DP) (OLG) (SL) (FP) (SL) (OF) (CE) (DP) (TS) (F) (OCce) (E) (SC) (OS) |
 |
[Page 19] Atlas Copco XAS 97 DD — 17 — Reference Name AF Air Filter AOV Air Outlet Valves AR Air Receiver BDV Blow Down Valve BOV Blow Off Valve CE Compressor Element CV Check Valve DP Drain Plug E Engine FFan FN Flow Nozzle FP Filler Plug FR Flow Restrictor OCce Oil Cooler (compre… |
 |
[Page 20] Atlas Copco XAS 97 DD — 18 — AIR FLOW Air drawn through the airfilter (AF) into the compressor element (CE) is compressed. At the element outlet, compressed air and oil pass into the air receiver/oil separator (AR/OS). The check valve (CV) prevents blow-back of compressed… |
 |
[Page 21] Atlas Copco XAS 97 DD — 19 — OIL SYSTEM The lower part of the air receiver (AR) serves as oil tank. Air pressure forces the oil from the air receiver/oil separator (AR/OS) through the oil cooler (OCce) and oil filter (OF) to the compressor element (CE). When the compresso… |
 |
[Page 22] Atlas Copco XAS 97 DD — 20 — CONTINUOUS REGULATING SYSTEM (UV) (UA) (VH) (RV) (SR) (AR) (CE) |
 |
[Page 23] Atlas Copco XAS 97 DD — 21 — The compressor is provided with a continuous regulating system. This system is provided with a blow-down valve which is integrated in the unloader assembly (UA). The valve is closed during operation by outlet pressure of the compressor element… |
 |
[Page 24] Atlas Copco XAS 97 DD — 22 — ELECTRIC SYSTEM Circuit diagram (standard) (9822 0797 01) S1 3 2 1 0 q q 21 20 6 8 7 9 24 25 28 29 3 5 4 21 8« 7« 1« 2« 12 14 4« 3« 26 27 12« 34 35 9´,10´,11´ p 12V DC 5« Te mp K1 General alarm (Lamp- tester) 13« 15« 14« 11 10 … |
 |
[Page 25] Atlas Copco XAS 97 DD — 23 — Reference Name F1 Circuit Breaker (10 A) G1 Alternator G2 Battery H1 Temperature Alarm Lamp H2 General Alarm Lamp K0 Starter Solenoid (part of M1) K1 Shut-down Relay K2 Blocking Relay K3 Override Start Relay K4 Start Relay M1 Starter Motor P1 … |
 |
[Page 26] Atlas Copco XAS 97 DD — 24 — Circuit diagram cold start (9822 0864 00) V1 K4 K5 F1 K4 S2 S3 K3 K2 H1 S4 H2 K2 K1 Y1 K0 P1 V2 G1 G2 P2 B+ D+ D- 7 6 2 85 86 30 87 8 3 3 3 3 9 9 9 2 16 11 87a 87 86 87 87 30 30 87a 85 15 10 30 30 13 14 87a K3 S5 K0 M1 M S6 K1K5 30 30 30 87… |
 |
[Page 27] Atlas Copco XAS 97 DD — 25 — Reference Name F1 Circuit Breaker (10 A) G1 Alternator G2 Battery H1 Temperature Alarm Lamp H2 General Alarm Lamp K0 Starter Solenoid (part of M1) M1 Starter Motor P1 Hourmeter P2 Glowplug S1 Contact Switch (Off-On- Override-start) S2 Temperat… |
 |
[Page 28] Atlas Copco XAS 97 DD — 26 — Operation of the electric circuit in detail Start switch S1 position 1: Line 2 on 12V contact K3 closed (13-11), lamp H2 is on. K4 excites contact K4 (18-15). Thermocontact element S5 normally closed, K1 excites contact K1 (1-4). Use of lamp t… |
 |
[Page 29] Atlas Copco XAS 97 DD — 27 — MARKINGS AND INFORMATION LABELS Compressor outlet temperature too high. Compressor outlet temperature. Compressor outlet pressure. Danger, outlet gases. Danger, hot surface. Electrocution hazard. Atlas Copco mineral compressor oil. Atlas Copc… |
 |
[Page 30] Atlas Copco XAS 97 DD — 28 — Operating instructions PARKING, TOWING AND LIFTING INSTRUCTIONS Safety precautions Attention PARKING INSTRUCTIONS Non-adjustable towbar with standard support leg without brakes Adjustable towbar with jockey wheel and brakes (A) Parking positi… |
 |
[Page 31] Atlas Copco XAS 97 DD — 29 — TOWING INSTRUCTIONS Label on towbar, towing instructions Non-adjustable towbar with standard support leg without brakes For both non-adjustable — and adjustable towbar, the towbar should be as level as possible and the compressor and towing ey… |
 |
[Page 32] Atlas Copco XAS 97 DD — 30 — SPILLAGE-FREE INSTRUCTION This compressor is fitted with a leak-proof undercarriage in order to protect the environment. Any leaking fluid is collected in case of malfunctions. This fluid can be removed via outlets, normally secured by caps. T… |
 |
[Page 33] Atlas Copco XAS 97 DD — 31 — LIFTING INSTRUCTIONS When lifting the compressor, the hoist has to be placed in such a way that the compressor, which must be placed level, will be lifted vertically. Keep lifting acceleration and retardation within safe limits. Preferably use… |
 |
[Page 34] Atlas Copco XAS 97 DD — 32 — STARTING / STOPPING BEFORE STARTING 1. Before initial start-up, prepare battery for operation if not already done. See section Recharging a battery. 2. With the compressor standing level, check the level of the engine oil. Add oil, if neces… |
 |
[Page 35] Atlas Copco XAS 97 DD — 33 — Before starting open the air outlet valve(s) (see section Compressor regulating system, AOV) and push circuit breaker button (F1) once (open hood first). Circuit breaker button should now be in position B. The control panel indicates receiver … |
 |
[Page 36] Atlas Copco XAS 97 DD — 34 — DURING OPERATION Regularly carry out following checks: 1. That regulating valve (see section Main Parts, RV) is correctly adjusted, i.e. starts decreasing the engine speed when reaching the preset working pressure in the receiver. 2. Check … |
 |
[Page 37] Atlas Copco XAS 97 DD — 35 — Maintenance USE OF SERVICE PAKS Service Paks include all genuine parts needed for normal maintenance of both compressor and engine. Service Paks minimize downtime and keep your maintenance budget low. Order Service Paks at your local Atlas Cop… |
 |
[Page 38] Atlas Copco XAS 97 DD — 36 — Maintenance schedule (continuation of page 35) Daily 50 hours after initial start-up Yearly or every 500 hours Oil coolers Clean Engine minimum and maximum speeds Check Check Torque of wheel nuts Check Check Brake system (if installed) Check… |
 |
[Page 39] Atlas Copco XAS 97 DD — 37 — (continuation of page 36) Notes 1. More frequently when operating in a dusty environment. 2. Replace the element after 1000 running hours or when the pressure drop exceeds 0.8 bar (11.6 psi). 3. Refer to the Deutz operation manual. 4. 500 hour… |
 |
[Page 40] Atlas Copco XAS 97 DD — 38 — LUBRICATION OILS High-quality, mineral, hydraulic or synthesized hydrocarbon oil with rust and oxidation inhibitors and anti-foam and anti-wear properties is recommended. The viscosity grade should correspond to the ambient temperature and ISO… |
 |
[Page 41] Atlas Copco XAS 97 DD — 39 — OIL SPECIFICATIONS Never mix synthetic with mineral oil. Remark: When changing from mineral to synthetic oil (or the other way around), you will need to do an extra rinse: After doing the complete change procedure to synthetic oil, run the uni… |
 |
[Page 42] Atlas Copco XAS 97 DD — 40 — OIL LEVEL CHECK CHECK ENGINE OIL LEVEL Also consult the Engine Operation Manual for the oil specifications, viscosity recommendations and oil change intervals. For intervals, see Preventive maintenance schedule for the compressor. Check engine… |
 |
[Page 43] Atlas Copco XAS 97 DD — 41 — OIL AND OIL FILTER CHANGE ENGINE OIL AND OIL FILTER CHANGE See section Preventive maintenance schedule for the compressor. The quality and the temperature of the oil determine the oil change interval. The prescribed interval is based on normal… |
 |
[Page 44] Atlas Copco XAS 97 DD — 42 — CLEANING COOLERS Keep the oil-coolers (1) and (2) clean to maintain the cooling efficiency. The fan side surface of compressor- and engine oil cooler is accessible by removing the fan cowl upper part. The opposite surface of compressor- and en… |
 |
[Page 45] Atlas Copco XAS 97 DD — 43 — BATTERY CARE If the battery is still dry, it must be activated as described in section Activating a dry-charged battery. The battery must be in operation within 2 months from being activated; if not, it needs to be recharged first. ELECTROLYTE… |
 |
[Page 46] Atlas Copco XAS 97 DD — 44 — CHANGING TYRES When changing a tyre, please observe that the arrow on the tyre in top position points in the driving direction (to the towbar). STORAGE Run the compressor regularly, e.g. twice a week, until warm. Load and unload the compressor… |
 |
[Page 47] Atlas Copco XAS 97 DD — 45 — Adjustments and servicing procedures ADJUSTMENT OF THE CONTINUOUS REGULATING SYSTEM The working pressure is determined by the tension of the spring in the regulating valve (RV). This tension can be increased to raise the pressure and decreased… |
 |
[Page 48] Atlas Copco XAS 97 DD — 46 — AIR FILTER ENGINE/COMPRESSOR MAIN PARTS CLEANING THE DUST TRAP To remove dust from the dust trap pinch the vacuator valve (6) several times. The Atlas Copco air filters are specially designed for the application. The use of non-genuine air fil… |
 |
[Page 49] Atlas Copco XAS 97 DD — 47 — REPLACING THE AIR FILTER ELEMENT New elements must also be inspected for tears or punctures before installation. Discard the element (4) when damaged. In heavy duty applications it is recommended to install a safety cartridge which can be orde… |
 |
[Page 50] Atlas Copco XAS 97 DD — 48 — FUEL SYSTEM Replacing the filter element 1. Unscrew the filter element (1) from the adapter head. 2. Clean the adapter head sealing surface. Lightly oil the gasket of the new element and screw the latter onto the header until the gasket is … |
 |
[Page 51] Atlas Copco XAS 97 DD — 49 — TEST PROCEDURE OF BRAKE CABLE ADJUSTMENT 2 — 3 teeth 1. Check if the towing eye rod of the overrun brake mechanism is in the outmost position. 2. Check if the adjustable towbar (= option) is in the actual towing position. 3. Apply the hand … |
 |
[Page 52] Atlas Copco XAS 97 DD — 50 — Problem solving It is assumed that the engine is in good condition and that there is adequate fuel flow to the filter and injection equipment. Make sure that the wires are not damaged and that they are clamped tight to their terminals. Alterna… |
 |
[Page 53] Atlas Copco XAS 97 DD — 51 — 3. Temperature alarm lamp (H1) does not light up when switching (S1) to ”I” and applying lamp test. a. Lamp (H1) blown b. See fault 1d. a. Replace lamp. b. See 1d. 4. Starter motor (S) does not crank engine (E) after switching startbutt… |
 |
[Page 54] Atlas Copco XAS 97 DD — 52 — 11. Compressor capacity or pressure below normal. a. Air consumption exceeds capacity of compressor. b. Choked air filter elements (AF). c. Unloading valve (UV) not completely open. d. Engine does not run at max. speed. e. Oil separator eleme… |
 |
[Page 55] Atlas Copco XAS 97 DD — 53 — Available options Pressure vessel approval: CE ASME Undercarriage: Adjustable towbar with brakes Fixed towbar with brakes Support (without undercarriage) Simplified bumper Towing eyes: Loose ball coupling Towbar support: Jockey wheel Air quali… |
 |
[Page 56] Atlas Copco XAS 97 DD — 54 — Technical specifications TORQUE VALUES GENERAL TORQUE VALUES The following tables list the recommended torques applied for general applications at assembly of the compressor. For hexagon screws and nuts with strength grade 8.8 For hexagon scre… |
 |
[Page 57] Atlas Copco XAS 97 DD — 55 — SETTINGS OF SHUTDOWN SWITCHES AND SAFETY VALVES Designation XAS 97 DD — XAS 185 DD7 Engine oil pressure bar(e) 1.2 psi 17.4 Engine oil temperature °C 127 — 133 °F 260 — 270 Compressor temperature °C 116 — 120 °F 241 — 248 Safety valve open… |
 |
[Page 58] Atlas Copco XAS 97 DD — 56 — COMPRESSOR / ENGINE SPECIFICATIONS REFERENCE CONDITIONS The inlet conditions are specified at the air inlet grating outside the canopy. Designation XAS 97 DD — XAS 185 DD7 Absolute inlet pressure bar(e) 1 psi 14.5 Relative air humidity % — Air… |
 |
[Page 59] Atlas Copco XAS 97 DD — 57 — LIMITATIONS 1) For Hose Reel application: maximum ambient temperature 30°C 2) Cold start equipment not available at time of release. Designation XAS 97 DD — XAS 185 DD7 Minimum effective receiver pressure bar(e) 4 psi 58 Maximum effective r… |
 |
[Page 60] Atlas Copco XAS 97 DD — 58 — ALTITUDE UNIT PERFORMANCE CURVE Max. allowable working pressure as a function altitude and ambient temperature. 4.0 bar(e) 58 psi 5.0 bar(e) 73 psi 6.0 bar(e) 87 psi 7.0 bar(e) 102 psi 16 405 13 124 9 843 6 562 3 281 0 5000 4000 3000 2000 1000… |
 |
[Page 61] Atlas Copco XAS 97 DD — 59 — PERFORMANCE DATA At reference conditions, if applicable, and at normal shaft speed, unless otherwise stated. 1 ) Free Air Delivery (volume flow rate) is measured according to ISO 1217 ed.3 1996 annex D Tolerance: • +/- 5% 25 l/s (53 cfm) <… |
 |
[Page 62] Atlas Copco XAS 97 DD — 60 — DESIGN DATA Compressor Engine 1) With filter change. Designation Number of compression stages 1 Designation XAS 97 DD — XAS 185 DD7 Make Deutz Type D2011L03 F3M2011 Coolant Oil Number of cylinders 3 Bore mm 94 in 3.7 Stroke mm 112 in 4.4 Swep… |
 |
[Page 63] Atlas Copco XAS 97 DD — 61 — Unit 1) Air required for engine and compressor element cooling, for combustion and for compression. Unit dimensions Designation XAS 97 DD — XAS 185 DD7 Capacity of compressor oil system l8 US gal 2.1 Net capacity of air receiver l 16.7 US ga… |
 |
[Page 64] Atlas Copco XAS 97 DD — 62 — Dataplate 1 Company code 2 Model 3 Unit serial number 4 Working pressure 5 Speed 6Engine power 7 Manufacturing year (1) (2) (3) (4) (5) (6) (7) |
 |
[Page 65] Atlas Copco XAS 97 DD — 63 — Disposal GENERAL When developing products and services, Atlas Copco tries to understand, address, and minimize the negative environmental effects that the products and services may have, when being manufactured, distributed, and used, as well … |
 |
[Page 66] Atlas Copco XAS 97 DD — 64 — Maintenance Log Compressor ……………………………………………………………………………… Customer ………………………………………………………………………………….. Serial number……… |
 |
[Page 67] Atlas Copco XAS 97 DD … |
 |
[Page 68] Atlas Copco XAS 97 DD www.atlascopco.com Atlas Copco Instruction Manual |