Garrett at pro инструкция на русском скачать бесплатно

Условия гарантии Запчасти Инструкции FAQ Сервисный центр

МИРОВОЙ ЛИДЕР В ТЕХНОЛОГИИ ОБНАРУЖЕНИЯ МЕТАЛЛОВ

vk.com

2021 © Garrett Metal Detectors | При использовании материалов ссылка на сайт обязательна. Все права защищены.

Quick Links

• Page 1
  Owner’s Manual…
• Page 2
  Standard Mode can be easily operated by the beginner. In order to take full advantage of the special features and functions of the AT Pro, you are urged to carefully read this instruction manual in its entirety. AT Pro International™…
• Page 3
  Garrett Metal Detectors…

• Page 4: Table Of Contents

  TABLE OF CONTENTS AT Pro CONTROL PANEL …………..4 QUICk START GUIDE …………….5 AT Pro COMPONENTS …………… 6 LIST OF PARTS ………………7 ASSEMBLy ………………8 POWERING ON ……………… 11 SEARCH MODES …………….12 Overview of STD Mode vs PRO Mode ……..12 Standard (STD) Detection Modes ……….

• Page 5: At Pro Control Panel

  AT Pro CONTROL PANEL Target ID Legend indicates Lower Scale metal types. Digital indicates notch Target ID Target ID discrimination pattern. Cursor (also shows indicates High Resolution ground balance probable Coin Depth Iron Discrimination settings while in target identity. Indicator indicates level of iron GND-BAL mode.)

• Page 6: Quick Start Guide

  The AT Pro operates with four (4) AA batteries which are already installed by Garrett. 2. Power ON. Press and release the ON / OFF Power button. The AT Pro powers on in the last mode used and is ready to search. (Factory default mode is Coins.) 3.

• Page 7: At Pro Components

  AT Pro COMPONENTS Search coil Lower Control Upper Stem Housing Stem Screen Pushbutton Controls Spring Clip strap S-shaped Stem Handle Grip Detector Stand Padded Arm Cuff Garrett Metal Detectors…

• Page 8: List Of Parts

  LIST OF PARTS No tools are required to assemble the AT Pro. Four (4) AA batteries are included with the detector. The box for your detector contains the following parts:  One (1) control housing with  One (1) 28×22 cm DD…

• Page 9: Assembly

  Insert the threaded bolt through the holes of the lower stem and searchcoil. Hand-tighten the searchcoil assembly with the wing nut. Depress the spring clip in the S-stem and insert the control housing into the upper stem. Garrett Metal Detectors…

• Page 10
  Insert the coil connector into the 4-pin connector of the control housing and hand-tighten. If needed, adjust the arm cuff by removing the screw on the bottom and moving it to the other hole. AT Pro International™…
• Page 11
  Note: Headphones are not required but are desired by many hunters to hear faint targets. Connecting the headphones will silence the detector’s speaker. Note: The provided headphones are for dry use only; see page 54 for optional waterproof headphones. 10 Garrett Metal Detectors…

• Page 12: Powering On

  To turn off the detector, press and hold this pushbutton for one (1) second (until the detector produces a second beep). To restore the factory settings, press and hold the power button for 5 to 10 seconds (until the detector produces a fast double beep). AT Pro International™…

• Page 13: Search Modes

  Custom, Coins or Zero in the STD Mode and Custom, Coins or Zero in the PRO Mode. • Overview of STD Mode vs PRO Mode In its Standard (STD) Mode, the AT Pro provides a full- strength audio response regardless of a target’s amplitude. Many detectorists prefer this consistent, unambiguous, binary (either on or off) target response.

• Page 14: Standard (Std) Detection Modes

  STANDARD (STD) DETECTION MODES In the STD modes, the AT Pro produces a full-strength binary audio beep to indicate a detected target. Standard detection mode operation is ideal for learning the AT Pro because of its consistent audio signals. Detected targets are heard at the same full-strength beep regardless of their size or depth.

• Page 15
  • CUSTOM Mode This mode can be customized by the operator and the AT Pro will retain the changes when the detector is switched off. The factory preset for the CUSTOM Mode is the same as the ZERO Mode (see previous page).

• Page 16: Pro Detection Modes

  PRO DETECTION MODES Zero, Coins or Custom have the same discrimination patterns as in STD Mode. In PRO Mode, however, the AT Pro utilizes its Pro Audio functions—including Proportional Audio and Tone Roll Audio—to offer more target information. The Pro Mode audio provides more target information and faster recovery speed for separating adjacent targets.

• Page 17
  In contrast, PRO Mode’s proportional audio provides a stronger signal for the shallow coin and a softer signal for the deeper coin. The actual profile, or signature, of the target’s response is heard, thereby providing more information. 16 Garrett Metal Detectors…
• Page 18
  Adjacent Targets Comparison: Standard vs Pro Mode Adjacent targets These two adjacent coins would produce one strong signal while in STD Mode. In PRO Mode, the proportional audio provides two peaks of audio response to allow the user to identify multiple targets. AT Pro International™…

• Page 19: Tone Roll Audio (Pro Mode)

  In PRO Mode, however, the bottle cap will produce a very distinctive response with multiple tones. As shown, the bottle cap will produce a distinctive response of Low-High-Low as compared to the coin’s response of only High tone. 18 Garrett Metal Detectors…

• Page 20: Target Id Information

  Pro will produce an audible target response for the pixels that are switched on, and no audible response for those that have been switched off. The Target ID Cursor will always indicate all targets. The discrimination pattern can be adjusted (as described in the «Discrimination» section). AT Pro International™…

• Page 21: Digital Target Id

  Digital Cursor Target The AT Pro’s Digital Target ID system provides a specific target value to help identify targets more precisely. Targets are identified on the LCD by number, with items near 1 being the most ferrous. The most conductive targets (such as thick silver) register closer to to 99.

• Page 22: Tone Id

  High/Bell Tone: Non-ferrous targets with medium to high conductivity, including most coins and jewelry. Note: PRO Mode produces a high tone; STD Mode produces a bell tone. AT Pro International™…

• Page 23: Discrimination

  ELIM Pushbutton Pushbutton The AT Pro has 12 pixels or «notches» of discrimination (in addition to the 40 points of High-Res Iron Discrimination). Any combination of these pixels can be switched on or off based upon your preference. There are two primary methods for modifying the Notch Discrimination Pattern to reject a specific type of trash or unwanted item.

• Page 24
  The AT Pro’s ELIM pushbutton can also be used to find specific metal items. For example, if an earring has been lost, scan the matching earring with the AT Pro while in the ZERO mode. Note where the Target ID cursor appears when the earring is scanned.

• Page 25: Iron Discrimination

  The AT Pro is now programmed to find the missing earring based on the conductivity of its matching pair. Note: The notch discrimination function can be used to modify each Mode’s discrimination pattern. Notch Discrimination modifications made while in CUSTOM (either in Standard or Pro mode) will be retained when the detector is switched OFF.

• Page 26
  «mask» out the signal of an adjacent good target when too much iron discrimination has been applied. Using the AT Pro’s High-Res Iron Discrimination, apply just enough iron discrimination to reject the undesired iron nail shown in this example. By using only a minimal amount of…
• Page 27
  Example: Detecting Targets in Trash with High-Res Iron Discrimination In the illustration above, the AT Pro is operating with an IRON DISC setting of 20. The nail seen in Illustration 1 (on page 25) registers from 10 to 25 on the Digital Target ID scale.

• Page 28: Iron Audio

  Iron Audio also allows adjustment of the mid-tone’s range to include all targets above the iron discrimination setting. The user is adjusting the cut-off between low-tone iron targets and mid-tone targets to better distinguish good targets. AT Pro International™…

• Page 29
  When Iron Audio is on in the PRO Mode, iron target will not only be heard, but they will produce an even more distinctive response with multiple tones. For example, a nail will produce several fast low tones as the searchcoil passes over. A flat 28 Garrett Metal Detectors…
• Page 30
  To fully appreciate the additional information offered by the Iron Audio feature, conduct the following experiment. Start with the AT Pro in Standard (STD) Zero Mode and pass the searchcoil over a bottle cap which is lying flat on the ground.

• Page 31: Sensitivity

  Sensitivity Pushbutton Indicator The AT Pro has eight (8) settings for sensitivity. Use the (+) or (-) SENSITIVITy buttons to step through the eight levels, which are continuously shown on the LCD. Use higher sensitivity levels when searching for very small or very deep targets.

• Page 32: Ground Balance

  NOTCH DISC pushbuttons for Manual Ground Balance. Detector performance can be negatively affected by ground mineralization. The AT Pro can be ground balanced either automatically or manually to cancel unwanted ground signals and obtain maximum stability and target detection.

• Page 33: Manual Ground Balance

  80–99: Highly ferrous (magnetite, ferrous oxide minerals, black sands, hot rocks, terra cotta) 60–80: Moderately mineralized soils (red clay, brown clay, iron-bearing clay minerals, etc.) 20–60: Likely an iron object 0–20: Highly conductive, non-ferrous minerals such as saltwater 32 Garrett Metal Detectors…

• Page 34: Frequency Adjustment

  Use the PINPOINT/Freq Adj pushbutton in conjunction with the (+) or (-) SENSITIVITy pushbuttons to adjust frequency. The AT Pro is capable of operating at four slightly different frequencies in order to minimize the interference caused by electrical sources (e.g. power lines) or other metal detectors.

• Page 35: Pinpointing

  Indicates mount. The opening pinpointing just ahead of the stem center of the mount can serve as 28 x 22 cm DD your reference point searchcoil. for pinpointing. 34 Garrett Metal Detectors…

• Page 36
  PINPOINT Pushbutton (Press and hold to pinpoint) Traditional pinpointing technique using Pinpoint pushbutton. Note: For best pinpointing results, maintain a constant height above the ground (e.g. 2cm) and ensure that the detector is properly ground balanced. AT Pro International™…

• Page 37: Narrowing The Detection Area

  Coin Depth Indicator—The depth of a coin, or similar sized target, is indicated in 5cm increments. Note: targets larger than a coin may display shallower than actual depth while targets smaller than a coin may display deeper than actual depth. 36 Garrett Metal Detectors…

• Page 38: Alternative Pinpointing Methods

  (see Image B). Deep targets will be under or just inside your searchcoil’s tip. This is because the conical shape of the searchcoil’s detection field begins bending in slightly as the depth increases. AT Pro International™…

• Page 39
  Tip: Practice any or all of these various pinpointing options in your test plot. Choose the technique that works best for you. As you improve your pinpointing accuracy, you will dig smaller holes and increase your productive hunting time. 38 Garrett Metal Detectors…

• Page 40: Hunting Tips

  • Keep your searchcoil at a constant height of 2 to 3 cm above and parallel to the ground at all times for best detection results. Do not lift or tilt the coil at the end of swings. CORRECT SWING INCORRECT SWING AT Pro International™…

• Page 41
  Walk slowly to allow overlapping of the searchcoil Scan side to side approx. 1m per second. 40 Garrett Metal Detectors…
• Page 42
  Continous Wave (VLF) metal detector. Saltwater is conductive and produces signals similar to foil. Although the AT Pro is not specifically designed for saltwater use, it can be used in this environment. The operator can expect stable operation in dry or moist sand and when the searchcoil is completely submerged.
• Page 43
  Magnetic minerals such as hot rocks and terra cotta can mask the presence of good targets. In order to detect a good target, first ground balance the AT Pro to the terra cotta or hot rocks that are present. Be aware, however, that the combined Target ID might be very low (e.g.
• Page 44
  • Isolating adjacent targets. The narrow detection field of the AT Pro’s DD searchcoil allows better separation of adjacent targets versus a similar size concentric searchcoil. Use narrow swings of the searchcoil in trashy areas to isolate good targets amongst the trash.

• Page 45: Bench Tests

  BENCH TESTS you should conduct bench tests to become more familiar with the AT Pro’s operation in both Standard and PRO modes. In addition, the use of the Iron Audio feature should be tested in both Standard and PRO modes. Suggested test items should include: •…

• Page 46
  Discrimination bench test: A similar test procedure can be used to better understand how to set discrimination levels and the AT Pro’s advanced audio characteristics. Begin by testing the iron nail in the STD and PRO Modes with the ZERO discrimination pattern. Listen to the Low-Tone sound an iron object creates and note the Digital Target ID number it produces.
• Page 47
  Final tip: Record the results of your bench tests and refer to them when hunting in the field. knowledge of the PRO Mode and the Iron Audio feature can reduce the amount of trash targets that are dug. 46 Garrett Metal Detectors…

• Page 48: Underwater Operation

  For submersion, optional waterproof headphones (available from Garrett) must be used. Waterproof headphones (sold separately) must be used if the AT Pro is fully immersed in water. The standard land-use headphones included with the detector are not waterproof.

• Page 49: Care And Maintenance

  CARE AND MAINTENANCE Battery Level Indicator Battery Replacement—The AT Pro is operating with fresh or fully charged batteries when 4 illuminated bars on the Battery Level Indicator (see above) are displayed. The detector will maintain full performance until the batteries need to be replaced.

• Page 50
  Pull and remove the cap to slide battery holder out. Remove batteries when the AT Pro will be stored for longer than 30 days. The AT Pro is a rugged machine, designed for outdoor use in all environments. However, as with all electronic equipment, there are some simple ways to care for the detector to maintain its high performance.

• Page 51: Troubleshooting Guide

  NOTE: Large, flat pieces of iron—depending on their orientation in the ground—can read as a good target or can cause erratic Target ID Cursor movement. Use Iron Audio feature to help identify iron targets. 50 Garrett Metal Detectors…

• Page 52: Metal Detecting Code Of Ethics

  • I will observe the Golden Rule, using good outdoor manners and conducting myself at all times in a manner which will add to the stature and public image of all people engaged in the field of metal detection. AT Pro International™…

• Page 53: Cautions

  • Use reasonable caution in digging toward any target, particularly in areas where you are uncertain of the ground conditions. • If you are unsure about using your metal detector in any area, always seek permission from the proper authorities. 52 Garrett Metal Detectors…

• Page 54: Warranty / Service

  Use of the AT Pro at submerged depths exceeding 3 meters will void this warranty. In the event you encounter problems with your AT Pro detector please read through this Owner’s Manual carefully to…

• Page 55: Accessories

  Use when searching for small, shallow targets or in trashy or tight places. 23 cm. PROformance Concentric Searchcoil— Part No. 2222600 Smaller and lighter than the AT Pro’s standard DD coil, this waterproof searchcoil offers excellent depth in less mineralized soils.

• Page 56
  Includes woven belt holster and 9-volt battery. To see Garrett’s complete collection of metal detector accessories, please visit www.garrett.com and view products within our Hobby Division. Additional searchcoils, recovery tools, headphones, carrying bags, searchcoil covers, Garrett caps and Garrett shirts are available for all detecting accessory needs. AT Pro International™…

• Page 57: Suggested Reading

  Charles Garrett. Collect them all! This edition includes the author’s personal experiences of hunting in Europe, plus tips and techniques. 76 pages. PN 1546200 Author/master treasure hunter (Available in English language only) Visit RAM Books on www.garrett.com for future releases. 56 Garrett Metal Detectors…

• Page 58
  RAM BOOkS TITLES RAM Books, a division of Garrett Metal Detectors, publishes new titles each year related to treasure hunting, gold pros- pecting, coin hunting and relic recovery. European Metal Suggested Reading: Detecting Guide Highlights include: • Hundreds of full-color photographs •…
• Page 59
  TO vIEW OTHER RAM BOOKS: Go to www.garrett.com and visit the Hobby Division. An order form is available on our site which can be printed and mailed with your requested titles and payment. 58 Garrett Metal Detectors…
• Page 60
  1881 W. State Street Garland, Texas 75042 Toll Free: 800.527.4011 Tel: 972.494.6151 Fax: 972.494.1881 Email: sales@garrett.com © 2010 Garrett Electronics, Inc. PN 1533300.A.1010…
• Page 61
  60 Garrett Metal Detectors…

• Описание
• Видео — обзор
• Доставка и оплата
• Отзывы

Советы кладоискателям

СОВЕТЫ КЛАДОИСКАТЕЛЯМ >>>

Видеообзоры металлоискателей, катушек и проч. снаряжения

ОБЗОРЫ МЕТАЛЛОИСКАТЕЛЕЙ >>>