Gigabyte z690 gaming x ddr4 инструкция на русском

1. Manuals
2. Brands
3. Gigabyte Manuals
4. Motherboard
5. Z690 GAMING X
6. User manual

• Page 1
  Z690 GAMING X Z690 GAMING X DDR4 For more product details, please visit GIGABYTE’s website. To reduce the impacts on global warming, the packaging materials of this product are recyclable and reusable. GIGABYTE works with you to protect the environment.
• Page 2
  The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.

• Page 3: Table Of Contents

  Table of Contents Chapter 1 Product Introduction ………………4 Motherboard Layout ………………4 Box Contents ………………..6 Chapter 2 Hardware Installation ………………7 Installation Precautions ………………7 Product Specifications ………………8 Installing the CPU and CPU Cooler …………… 12 Installing the Memory ………………15 Installing an Expansion Card ……………..

• Page 4: Chapter 1 Product Introduction

  Chapter 1 Product Introduction Motherboard Layout LED_C2 ATX_12V_2X4 CPU_OPT D_LED2 CPU_FAN USB20 ATX_12V_2X2 USB 2.0 Hub LGA1700 U32G2 DP_HDMI20 U320G U32_LAN AUDIO PCIEX16 Realtek ® 2.5GbE LAN THB_C2 THB_C1 Intel Z690 ® ® Super I/O CODEC PCIEX4_1 M_BIOS USB 2.0 Hub PCIEX4_2 RST_SW SYS_FAN2…

• Page 5
  LED_C2 ATX_12V_2X4 CPU_OPT D_LED2 CPU_FAN USB20 ATX_12V_2X2 USB 2.0 Hub LGA1700 U32G2 DP_HDMI20 U320G U32_LAN AUDIO PCIEX16 Realtek ® 2.5GbE LAN THB_C2 THB_C1 Intel Z690 ® ® Super I/O CODEC PCIEX4_1 M_BIOS USB 2.0 Hub PCIEX4_2 RST_SW SYS_FAN2 CLR_CMOS QFLED LED_C1 F_AUDIO D_LED1…

• Page 6: Box Contents

  Box Contents Z690 GAMING X or Z690 GAMING X DDR4 motherboard User’s Manual Two SATA cables M.2 screws * The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

• Page 7: Chapter 2 Hardware Installation

  Chapter 2 Hardware Installation Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user’s manual and follow these procedures: • Prior to installation, make sure the chassis is suitable for the motherboard. •…

• Page 8: 2-2 Product Specifications

  Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules Š Support for Extreme Memory Profile (XMP) memory modules Š (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) Onboard Integrated Graphics Processor-Intel HD Graphics support: ®…

• Page 9
  Storage Interface Š CPU: 1 x M.2 connector (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2 SSD support) (M2A_CPU) Chipset: Š 2 x M.2 connector (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2 SSD support) (M2P_SB, M2Q_SB) 1 x M.2 connector (Socket 3, M key, type 2260/2280/22110 SATA and PCIe 4.0 x4/x2 SSD support) (M2M_SB) 6 x SATA 6Gb/s connectors Support for RAID 0, RAID 1, RAID 5, and RAID 10…
• Page 10
  Back Panel 1 x USB Type-C port, with USB 3.2 Gen 2×2 support ® Š Connectors 2 x USB 3.2 Gen 2 Type-A ports (red) Š 3 x USB 3.2 Gen 1 ports Š 4 x USB 2.0/1.1 ports Š 1 x HDMI port Š…
• Page 11
  System ATX Form Factor; 30.5cm x 24.4cm Form Factor Š * GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice. Z690 GAMING X Z690 GAMING X DDR4 Please visit GIGABYTE’s website for support lists of CPU, memory modules, SSDs, and M.2 devices.

• Page 12: Installing The Cpu And Cpu Cooler

  Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE’s website for the latest CPU support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage.

• Page 13
  B. Installing the CPU Follow the steps below to correctly install the CPU into the motherboard CPU socket. Finger Tab j G ently press the CPU socket lever handle down and away from the socket. k C ompletely lift up the CPU socket lock- ing lever.
• Page 14
  C. Installing the CPU Cooler Be sure to install the CPU cooler after installing the CPU. (Actual installation process may differ depending the CPU cooler to be used. Refer to the user’s manual for your CPU cooler.) Apply an even and thin layer of thermal grease on the surface of the installed CPU.

• Page 15: Installing The Memory

  Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE’s website for the latest supported memory speeds and memory modules.) •…

• Page 16: Installing An Expansion Card

  Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. • Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

• Page 17: Back Panel Connectors

  The reversible USB port supports the USB 3.2 Gen 2×2 specification and is compatible to the USB 3.2 Gen 2, USB 3.2 Gen 1, and USB 2.0 specifications. Use this port for USB devices. (Note) To enable the Q-Flash Plus function, please navigate to the «Unique Features» page of GIGABYTE’s website for more information. — 17 -…

• Page 18
  • When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector. Please visit GIGABYTE’s website for details on configuring the audio software. — 18 -…

• Page 19: Internal Connectors

  Internal Connectors ATX_12V_2X2/ATX_12V_2X4 F_AUDIO F_U32C CPU_FAN F_U32 SYS_FAN1/2/3 F_USB1/F_USB2 SYS_FAN4_PUMP SPI_TPM CPU_OPT THB_C1/THB_C2 SATA3 2/3/4/5/6/7 CLR_CMOS D_LED1/D_LED2 LED_C1/LED_C2 RST_SW/RST M2A_CPU/M2P_SB/M2Q_SB/M2M_SB QFLASH_PLUS F_PANEL CPU/DRAM/VGA/BOOT Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. •…

• Page 20
  1/2) ATX_12V_2X2/ATX_12V_2X4/ATX (2×2, 2×4, 12V Power Connectors and 2×12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed.

• Page 21: Cpu_Fan

  For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. The header also provides speed control for a water cooling pump. Please navigate to the «BIOS Setup» page of GIGABYTE’s website and search for «Smart Fan 6» for more information. Pin No. Definition…

• Page 22
  Each SATA connector supports a single SATA device. The Intel Chipset supports RAID 0, RAID 1, ® RAID 5, and RAID 10. Please navigate to the «Configuring a RAID Set» page of GIGABYTE’s website for instructions on configuring a RAID array. Pin No. Definition SATA3 To enable hot-plugging for the SATA ports, please navigate to the «BIOS Setup»…

• Page 23: Led_C1

  Incorrect connection may lead to the damage of the LED strip. For how to turn on/off the lights of the LED strip, please navigate to the «Unique Features» page of GIGABYTE’s website. Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.

• Page 24
  RAID set either with an M.2 SATA SSD or a SATA hard drive. Please navigate to the TPM_new OC_LED/OC_BT SPI_TPM GPIOX8 EXT_PWR «Configuring a RAID Set» page of GIGABYTE’s website for instructions on configuring a RAID array. M2_10G with WIFI module M2_WIFI MINI PCIE SPDIF_O (4-pin) GPIOX8…
• Page 25
  Installation Notices for the M.2 and SATA Connectors: The availability of the SATA connectors may be affected by the type of device installed in the M.2 sockets. The M2M_SB connector shares bandwidth with the SATA3 2, 3 connector. Refer to the following table for details. •…
• Page 26
  Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (please navigate to the «BIOS Setup» page of GIGABYTE’s website and search for «Soft-Off by PWR-BTTN» for more information).

• Page 27: Thb_C2

  F_USB3 (Front Panel) Z97X-SOC Force) M2_10G LED_IO (4-pin) OC_LED/OC_BT TPM_new SPI_TPM 12) F_AUDIO (Front Panel Audio Header) M2_WIFI The front panel audio header supports High Definition audio (HD). You may connect your chassis front J_HDMI(NH) SATA_SGP panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header.

• Page 28
  14) F_U32 (USB 3.2 Gen 1 Header) F_USB30 F_AUDIO(H) F_PANEL(NH) The header conforms to USB 3.2 Gen 1 and USB 2.0 specification and can provide two USB ports. For purchasing the optional 3.5″ front panel that provides two USB 3.2 Gen 1 ports, please contact the local dealer.

• Page 29: Thb_C1

  GPIOX8 EXT_PWR M2_10G with W THB_C1 SYS_FAN VROC 17) THB_C1/THB_C2 (Thunderbolt Add-in Card Connectors) ™ MINI PCIE The connectors are used to connect to a GIGABYTE Thunderbolt add-in card. ™ LED_C(5-pin) SPDIF_O (4-pin) M2_32G with GC-M2-U2 LED_DDR THB_C1 SYS_FAN VROC…

• Page 30: Bat Rst_Sw

  CMOS values. • After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (please navigate to the «BIOS Setup» page of GIGABYTE’s website for more information). 19) BAT (Battery) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off.

• Page 31
  RST_SW The reset button (RST_SW)/rest jumper (RST) provides you with several functions to use. To remap the button to perform different tasks, please navigate to the «BIOS Setup» page of GIGABYTE’s website and search for «RST_SW (MULTIKEY)» for more information.
• Page 32
  SATA_Express LED_DDR 22) CPU/DRAM/VGA/BOOT (Status LEDs) The status LEDs show whether the CPU, memory, graphics card, and operating system are working properly after system power-on. If the CPU/DRAM/VGA LED is on, that means the corresponding device is not working normally; if the BOOT LED is on, that means you haven’t entered the operating system yet. F_USB31C F_USB30/3 THB_C…

• Page 33: Chapter 3 Bios Setup

  If this occurs, try to clear the CMOS values and reset the board to default values. • Refer to the introductions of the battery/clear CMOS jumper in Chapter 2 or navigate to the «BIOS Setup» page of GIGABYTE’s website and search for «Load Optimized Defaults» for how to clear the CMOS values.

• Page 34
  Startup Screen: The following startup Logo screen will appear when the computer boots. Function Keys Function Keys: <DEL>: BIOS SETUPQ-FLASH Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup. <F12>: BOOT MENU Boot Menu allows you to set the first boot device without entering BIOS Setup.

• Page 35: Chapter 4 Installing The Operating System And Drivers

  RST VMD Controller driver first during the OS installation process. Refer to the steps below: Step 1: Go to GIGABYTE’s website, browse to the motherboard model’s web page, download the Intel SATA Preinstall driver file on the SupportDownloadSATA RAID/AHCI page, unzip the file and copy the files to your USB thumb drive.

• Page 36: Drivers Installation

  After you install the operating system, a dialog box will appear on the bottom-right corner of the desktop asking if you want to download and install the drivers and GIGABYTE applications via APP Center. Click Install to proceed with the installation. (In BIOS Setup, make sure SettingsIO PortsAPP Center Download & Install ConfigurationAPP Center Download &…

• Page 37: Chapter 5 Appendix

  • An M.2 PCIe SSD cannot be used to set up a RAID set either with an M.2 SATA SSD or a SATA hard drive. • Refer to «Internal Connectors,» for the installation notices for the M.2 and SATA connectors. Please visit GIGABYTE’s website for details on configuring a RAID array. — 37 -…

• Page 38: Regulatory Notices

  European Commission Delegated Directive (EU) 2015/863 Statement 2014/30/EU; Diretiva RSP 2011/65/UE. A conformidade com estas diretivas GIGABYTE products have not intended to add and safe from hazardous é verificada utilizando as normas europeias harmonizadas. substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP and DIBP).

• Page 39
  — 39 -…

• Page 40: Contact Us

  Contact Us GIGA-BYTE TECHNOLOGY CO., LTD. Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231, Taiwan TEL: +886-2-8912-4000, FAX: +886-2-8912-4005 Tech. and Non-Tech. Support (Sales/Marketing) : https://esupport.gigabyte.com WEB address (English): https://www.gigabyte.com WEB address (Chinese): https://www.gigabyte.com/tw GIGABYTE eSupport • To submit a technical or non-technical (Sales/Marketing) question, please link to: https://esupport.gigabyte.com…

X

You may only add up to 5 items for comparison at one time.

Закрыть