Janome sewist 525s инструкция по эксплуатации

11:01

Janome 521 & 525s Sewing Machines Review (Part-1)

06:29

Швейная машина Janome Sewist 525S

02:58

How to thread a sewing machine | Janome 525S

07:38

Janome 525s.А стоит ли…? Диагностика и разборка.Часть1

02:08

Швейная машина Janome Sewist 525s

1. Manuals
2. Brands
3. Janome Manuals
4. Sewing Machine
5. 525S —
6. Instruction book

• Page 1
  INSTRUCTION BOOK Model 525S…

• Page 2: Important Safety Instructions

  IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the followings: Read all instructions before using this appliance. DANGER — To reduce the risk of electric shock: An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.

• Page 3: Table Of Contents

  TABLE OF CONTENTS SECTION 1. KNOW YOUR MACHINE SECTION 4. UTILITY STITCHES Names of Parts ………….. 2 Basic Zigzag …………..20 Standard Accessories ………… 3 Overcasting …………..20 Accessory storage …………3 Knit Stitch …………..21 Extension Table …………. 4 Tricot Stitch (Multiple Zigzag Stitch) ……

• Page 4: Section 1. Know Your Machine

  SECTION 1. KNOW YOUR MACHINE Names of Parts q Bobbin winder stopper w Bobbin winder spindle e Hole for additional spool pin r Spool holder t Spool pin y Bobbin winder thread guide u Thread take-up lever i Foot pressure dial o Face plate !0 Thread cutter !1 Needle threader…

• Page 5: Standard Accessories

  Standard Accessories q Overedge foot C w Zipper foot E e Blind hemming foot G r Buttonhole foot B t Automatic buttonhole foot R y Needles u Bobbins i Screwdriver o Lint brush !0 Seam ripper (buttonhole opener) !1 Quilting guide !2 Spool holder (large) !3 Spool holder (small) !4 Additional spool pin…

• Page 6: Extension Table

  Extension Table To detach: Pull the extension table to the left. To attach: Insert the pin into the hole and push the extension table to snap it in place. q Pin w Hole Free-arm sewing Free-arm sewing is used for stitching sleeves, waistbands, pant legs or any other tubular garments.

• Page 7: Section 2. Getting Ready To Sew

  If it does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. The foot controller Model YC-482J or TJC-150 is used with the sewing machine Model 525S (USA market only).

• Page 8: Reverse Stitch Lever

  Reverse Stitch Lever Push the reverse stitch lever down to sew in reverse. The machine will sew in reverse while the lever is pushed. Foot Pressure Dial Turn the foot pressure dial to adjust the foot pressure. The foot pressure dial should be set at “3” for regular sewing.

• Page 9: Raising And Lowering The Presser Foot

  Raising and Lowering the Presser Foot The presser foot lifter raises and lowers the presser foot. You can raise the foot about 1/4″ (0.6 cm) higher than the normal up position for easy removal of the presser foot, or to help you place heavy fabric under the foot. q Lowered position w Normal up position e Extra up position…

• Page 10: Changing Needles

  Changing Needles CAUTION: Always make sure to turn the power switch off and disconnect the machine from power supply before changing the needle. Raise the needle by turning the handwheel and lower the presser foot. Turn off the power switch. z Loosen the needle clamp screw by turning it counterclockwise.

• Page 11: Winding The Bobbin

  Winding the Bobbin Setting the spool Place a spool of thread on the spool pin with the thread coming off the spool as illustrated. A: Press the large spool holder firmly against the spool of thread. q Large spool holder B: For a small spool, use the small spool holder.

• Page 12: Winding The Bobbin

  Winding the bobbin z Pull out the handwheel to disengage the clutch. q Handwheel x Draw the thread from the spool. Guide the thread around the bobbin winder thread guide. w Bobbin winder thread guide c Thread through the hole in the bobbin from the inside to the outside.

• Page 13: Inserting The Bobbin

  Inserting the bobbin z Place the bobbin in the bobbin holder with the thread running off as illustrated. q Thread x Guide the thread into the front notch on the front side of the bobbin holder. Draw the thread to the left, sliding it between the tension spring blades.

• Page 14: Threading The Machine

  Threading the Machine To set the needle thread: Raise the thread take-up lever to the highest position by turning the handwheel. Raise the presser foot. z Draw the thread from the spool and pass it under the thread guide. Then draw it down along the right channel.

• Page 15: Needle Threader

  Needle threader z Raise the needle to its highest position and lower the presser foot. Push down the needle threader knob as far as it will go. The hook comes out through the needle eye from behind. q Threader knob x Draw the thread from the left around the guide and under the hook.

• Page 16: Drawing Up The Bobbin Thread

  Drawing up the Bobbin Thread z Raise the presser foot and hold the needle thread lightly with your left hand. q Needle thread x Turn the handwheel slowly toward you one complete turn. Bring the bobbin thread up by pulling the needle thread as illustrated.

• Page 17: Selecting The Stitch Pattern

  Selecting the Stitch Pattern Raise the needle to its highest position. Pattern selector dial Turn the pattern selector dial to set the symbol of the desired stitch pattern at the setting mark. q Pattern selector dial w Setting mark CAUTION: Do not turn the pattern selector dial while the needle is in the fabric, otherwise the needle may bend or break.

• Page 18: Adjusting Stretch Stitch Balance

  Adjusting stretch stitch balance If the stretch stitch patterns are uneven when you sew on a particular fabric, correct them by turning the stitch length dial. If the patterns are drawn out, correct them by setting the “–” “+” dial to the “–” side. If the patterns are compressed, correct them by setting the dial to the “+”…

• Page 19: Balancing Needle Thread Tension

  Balancing Needle Thread Tension The thread tension should be adjusted depending on the sewing materials, layers of fabric and sewing method. To adjust the thread tension, turn the tension dial. q Tension dial Balanced tension: The ideal straight stitch has threads locked between two layers of fabric, as illustrated.

• Page 20: Straight Stitch Sewing

  SECTION 3. BASIC SEWING Straight Stitch Sewing Machine setting: q Stitch pattern: A w Stitch width: 0 or 5 e Stitch length: 1.5 – 4 r Thread tension: 2 – 6 t Presser foot: Zigzag foot A Starting to sew Raise the presser foot and place the fabric under the foot.

• Page 21: Seam Guides On The Needle Plate

  Seam guides on the needle plate The seam guides on the needle plate help you to measure seam allowance. The numbers indicate the distance between the center needle position and the seam guide. q Seam guides Number 20 4/8 5/8 6/8 Spacing (cm) 1.5 2.0 1.3 1.6 1.9 Spacing (inch)

• Page 22: Section 4. Utility Stitches Basic Zigzag

  SECTION 4. UTILITY STITCHES Basic Zigzag Machine setting q Stitch pattern: C w Stitch width: 1 – 5 e Stitch length: 0.5 – 3 r Thread tension: 2 – 5 t Presser foot: Zigzag foot A Simple zigzag stitching is widely used for overcasting, sewing on buttons etc.

• Page 23: Knit Stitch

  Knit Stitch Machine setting q Stitch pattern: G w Stitch width: e Stitch length: S.S. r Thread tension: 3 – 7 t Presser foot: Overedge foot C This stitch is ideal for finishing edges of stretch fabrics. It seams and finishes the fabric edges simultaneously. Place the edge of the fabric next to the guide of foot and sew while guiding the fabric edge along the guide.

• Page 24: Straight Stretch Stitch

  Straight Stretch Stitch Machine setting q Stitch pattern: A w Stitch width: 0 or 5 e Stitch length: S.S. r Thread tension: 2 – 5 t Presser foot: Zigzag foot A The pattern is sewn with two stitches forward and one stitch backward, forming a seam that does not rip easily.

• Page 25: Button Sewing

  Button Sewing Machine setting q Stitch pattern: C w Stitch width: Adjust as necessary e Stitch length: r Thread tension: 3 – 7 t Presser foot: Buttonhole foot B y Feed dog: Lowered Unthread the needle. Adjust the stitch width to match it with the span of the holes in the button.

• Page 26: Automatic Buttonhole

  Automatic Buttonhole Machine setting q Stitch pattern: BH w Stitch width: 4 – 5 e Stitch length: 0.5 – 1 r Thread tension: 1 – 5 t Presser foot: Automatic buttonhole foot R NOTES: The size of buttonhole is automatically determined by placing the button in the automatic buttonhole foot.

• Page 27
  c Pull the buttonhole lever down as far as it will go. r Buttonhole lever v Raise the foot and pass the needle thread through the opening in the foot. Draw both needle and bobbin threads to the left. Insert the fabric under the foot and lower the needle into the fabric at the starting point.

• Page 28: Adjusting The Buttonhole Stitch Density

  To sew another buttonhole, turn the stitch selector to “RESET”, then back to “ ” again, as shown. Now, simply step on the foot control to sew an identical buttonhole. m When buttonhole sewing is finished, push the buttonhole lever up as far as it will go. Adjusting the buttonhole stitch density Turn the stitch length dial within the range of “…

• Page 29: Corded Buttonhole

  Corded Buttonhole Machine setting q Stitch pattern: BH w Stitch width: 4 – 5 e Stitch length: 0.5 – 1 r Thread tension: 1 – 5 t Presser foot: Automatic buttonhole foot R z With the buttonhole foot raised, hook the filler cord on the spur at the back of the foot.

• Page 30: Manual Buttonhole

  Manual Buttonhole Machine setting q Stitch pattern: BH w Stitch width: 4 – 5 e Stitch length: 0.5 – 1 r Thread tension: 1 – 5 t Presser foot: Buttonhole foot B If the diameter of the button is more than 1″ (2.5 cm), a buttonhole must be made manually as follows: z Replace the foot with the buttonhole foot B.

• Page 31
  b Restart the machine to sew the back bartack and right row, and then stop the machine at the starting point. n When buttonhole sewing is finished, push the buttonhole lever up as far as it will go.

• Page 32: Zipper Application

  Zipper Application Machine setting q Stitch pattern: A w Stitch width: e Stitch length: 1.5 – 4 r Thread tension: 3 – 6 t Presser foot: Zipper foot E Attaching the zipper foot A: To sew the left side of the zipper, attach zipper foot with the right side pin.

• Page 33
  To sew z Attach zipper foot with the right side pin. Fold back the upper layer seam allowance. Fold back the lower layer seam allowance to leave a 1/8″ (0.4 cm) margin of fabric. q Lower layer w End of the opening e Zipper teeth r 1/8”…
• Page 34
  b Raise and release the foot, and re-attach it with the left side pin. Starting just below zipper bottom stop, sew across fabric to about 3/8″ (1 cm) distance from the basting line. Turn fabric 90 degrees and sew a seam the entire length of the zipper tape.

• Page 35: Blind Hemming

  Blind Hemming Machine setting q Stitch pattern: E or F w Stitch width: 2 – 3 e Stitch length: 2 – 3 r Thread tension:1 – 4 t Presser foot: Blind hemming foot G z On heavy weight fabrics that ravel, the raw edge should be overcast first.

• Page 36: Section 5. Decorative Stitches

  SECTION 5. DECORATIVE STITCHES Decorative Satin Stitches Machine setting q Stitch pattern: I – L w Stitch width: 3 – 5 e Stitch length: 0.5 – 1 r Thread tension:1 – 4 t Presser foot: Zigzag foot A or Buttonhole foot B Determine the appropriate stitch density by test sewing.

• Page 37: Smocking

  Smocking Machine setting q Stitch pattern: D w Stitch width: 3 – 5 e Stitch length: S.S. r Thread tension:1 – 4 t Presser foot: Zigzag foot A Step 1: Choose a soft and lightweight fabric such as batiste, gingham or challis. Cut the fabric three times wider than the project width.

• Page 38: Quilting

  Quilting Machine setting q Stitch pattern: A w Stitch width: 0 or 5 e Stitch length: 1.5 – 4 r Thread tension:3 – 6 t Presser foot: Zigzag foot A y Quilting guide The quilting guide will help keep the seam spacing constant.

• Page 39: Pin Tucking

  Pin Tucking Machine setting q Stitch pattern: A w Stitch width: 0 or 5 e Stitch length: 1.5 – 3 r Thread tension:2 – 6 t Presser foot: Blind hemming foot G Fold a fabric wrong side together and Lower the needle into the fabric 0.1 –…

• Page 40: Fagoting

  Fagoting Machine setting q Stitch pattern: H w Stitch width: 3 – 5 e Stitch length: 1 – 3 r Thread tension:1 – 4 t Presser foot: Zigzag foot A Use this stitch to join two pieces of fabric to create an open work appearance, and add design interest.

• Page 41: Appliqué

  Appliqué Machine setting q Stitch pattern: C w Stitch width: 3 – 5 e Stitch length: 0.5 – 1 r Thread tension:1 – 4 t Presser foot: Buttonhole foot B y Foot pressure: “2” Baste appliqué pieces on the fabric, or fuse the appliqué pieces with an iron-on fabric joiner.

• Page 42: Section 6. Care And Maintenance

  SECTION 6. CARE AND MAINTENANCE WARNING: Turn the power switch off and unplug the machine before cleaning. NOTE: Do not dismantle the machine in any way other than what is explained in this section. Clean the outside of the machine with a soft cloth and mild soap.

• Page 43: Replacing The Bobbin Holder

  Replacing the Bobbin Holder z Insert the bobbin holder into the hook race. x Make sure the knob of the bobbin holder fits next to the stopper on the race. q Knob w Stopper c Replace the bobbin. Attach the needle plate, inserting the two guide pins into the holes in the needle plate.

• Page 44: Troubleshooting

  Troubleshooting Reference Condition Cause 1. The needle thread is not threaded properly. Page 10 The needle thread 2. The needle thread tension is too tight. Page 17 breaks. 3. The needle is bent or blunt. Page 8 4. The needle is incorrectly inserted. Page 8 5.

• Page 45
  507-800-037 (E) Printed in Taiwan…