Катерпиллер 3512 руководство по эксплуатации

• 55, SEBU7348-05 107 Maintenance Section Walk-Around Inspection Removal and Installation For options re garding the removal, installation, repair and replacement, consult your Caterpillar dealer. Refer to the Service Manual for this engine or consult you r Caterpillar dealer for the procedure and specifications. Cleaning and Inspecting 1. Remove the e xhaust outlet piping and rem…

• 21, SEBU7348-05 73 Maintenance Section Driven Equipment — Check Dampers With Sampling P orts g008 19045 Illustration 46 Some dampers have ports for fluid samples. If the damper has no external damage, collect a sample of the damper fluid. The fluid should be analyzed in order to check for a loss of viscosity. Use the results of the analysis to determine if the dam…

• 4, 56 SEBU7348-05 Maintenance Section Maintenance Interval Schedule Every 1000 Serv ice Hours Engine — Clean ……………………………………………… 74 Engine Crankc ase Breather — Clean ………………… 80 Engine Protection Devices — Calibrate ……………… 86 Every 2000 Service Hours Air Starting Motor Lubricator Bowl — Clean ……….. 59 Crankshaft Vibration Da…

• 13, Caterpillar 3512B SEBU7348-05 65 Maintenance Section Cooling System Coolant (DEAC) — Change 3. Open the coolin g system drain valves (if equipped). If the cooling system is not equipped with drain valves, remove drain plugs (1) and (2). Allow the cool ant to drain. NOTICE Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine coolin…

• 17, SEBU7348-05 69 Maintenance Section Cooling System Coolant Sample (Level 1) — Obtain Remove the cool ing system fillercapslowlyinorder to relieve any pressure. Maintain the coolant within 13 mm (0.5 inch) below the bottom of the filler pipe. Add Coolant Note: For the proper coolant mixture to use, see this Operation and Maintenance Manual, “Refill Capacities a nd Recommendations�…

• 51, Caterpillar 3512B SEBU7348-05 103 Maintenance Section Overhaul Considerations • Pistons • Piston pins • Prelube pump • Pushrods • Rocker arms • Spacer plate • Software up date • Turbocharger Inspection of Components Inspect th e following components according to the instructions that are in Caterpillar reusability publications. Refer to Guidelines for Reusable Parts and Salvage…

• 19, SEBU7348-05 71 Maintenance Section Cooling System Supplemental Coolant Additive (SCA) — Test/Add Note: Caterpil lar recommends an S·O·S coolant analysis (Level 1). Cooling Systems that Use Conventional Coolant This maintenance procedure is required for conventiona l coolants such as DEAC.This maintenance is NOT required f or cooling systems that are filled with Extended Lif…

• 42, 94 SEBU7348-05 Maintenance Section Instrument Panel — Inspect Table 2 4 Engine Performance Engine Serial Number Authorization Date Engine hours Engine rpm Percent of load Ambient temperature Inlet manifold air temperature Inlet manifold air pressure Air restriction (left) Air restriction (right) Jacket water temperature Engine oil temperature Engine oil pressure Fuel p…

• 45, SEBU7348-05 97 Maintenance Section Overhaul (Major) Severe operati on can accelerate component wear. Engines that are operating under severe conditions may need more frequent maintenance intervals for the following reasons: • Maximum reliability • Retention of full service life Because of i ndividual applications, it is not possible to identify all of the factors which…

• 54, Caterpillar 3512B 106 SEBU7348-05 Maintenance Section Turbocharger — Inspect Inspect the sta rting motor for proper operation. Listen for grinding when the engine is started. Inspect the teeth of the starting motor pinion and the flywheel ring gear. Loo k for patterns of wear on the teeth. Look for teeth that are broken or chipped. If damaged teeth are found, the starting motor pinion…

• BRIGGSOperating & MaintenanceInstructionsModel SeriesCovered inThis Manual90000100000[ ModelType Code1Note: General Model Series numbers noted above are inclusive of the specific modelnumber found on your engine. To get replacement parts or technical assistance inthe future, write your engine Model, Type, Code and date of purchase here. fl°ith/ _aY ( YiarTABLE OF CONT …

  Classic 100000 20

• iThank YouThank you for choosing MotorGuide, one of the finest trollingmotors available. Years of experience have been committed to thegoal of producing the finest quality products. This led toMotorGuide’s reputation for strict quality control, excellence,durability, long‑lasting performance and being the best at providingafter‑the‑sale service a …

  T30 29

• Revision: SCE-IOM (01-22) 207697-BMODEL SCEINSTALLATION/OPERATION/MAINTENANCE FOR SEPARATED-COMBUSTION PACKAGED FURNACE/BLOWERSupersedes: I-SCE (04-21) 207697-A ⚠ DANGER ⚠  FIRE OR EXPLOSION HAZARD • Failure to follow safety warnings exactly could result in serious injury, death, or property damage. • Improper installation, adjustment, alteration, service, or maintenance …

  SCE 56

• Owners Manual 1 OWNERS MANUAL BUKH V8 SERIES ENGINE In 2009, marine diesel engines were introduced as 6.6L V8 turbo charged, common rail, intercooled marine engines for light duty commercial and pleasure craft applications. The production was transferred to BUKH A/S, in 2018 and relocated to Denmark. The lightweight and high performance 6.6L base engine is upgraded …

  V8 Series 376

• SEBU8024-03 15 Safety Section Engine Electronics The ECM sends a high voltage signal to the unit injectors. To help prevent personal injury, do not disconnect the unit injector connector while the engine is operating. Do not come in contact with the harness connector for the unit injector while the engine is operating. Tampering with the electronic system installation of the OEM wiring installation can be dangerous and could result in personal injury or death and/or engine damage. Note: Themonitoringsystemcanonlybe programmed with

• 6 SEBU8024-03 Safety Section Safety Messages Safety Section i02307008 Safety Messages SMCS Code: 1000; 7405 There may be several specific safet y messages on your engine. The exact location and a description of the messages are reviewed in this sectio n. Please become familiar w ith all o f the messages. Ensure that all of the messages are legible. Clean the m essages or replace the mes sages if the words cann ot be read or if th e illustrations are not visible. Use a cloth, water, and soap for cleaning the messa

• 14 SEBU8024-03 Safety Section Engine Stopping Use e th er in we ll ventilated areas. Use ether with care in order to avoid fires. Keep ether cylinders out of the reach of unauthorized persons. Store ether cylinders in authorized s torage areas only. Do not store ether cylinders in direct sunlight or at temperatures above 49 °C (120 °F). Discard the ether cylinders in a safe place. Do not puncture the ether cylinders. Do not burn the ether cylinders. i01964154 Engine Stopping SM

• SEBU8024-03 7 Safety Section Safety Message s Engine Lifting g00580494 Illustration 2 Location of the safety message for lifting the engine The safety message for lifting the engine is located on the valve covers. g00306083 Improper lift rigging can allow unit to tumble caus- ing injury and damage. Before lifting the engine, read this Operation and Maintenance Manual, “Engine Lifting” topic (Operation Section). If improper equipment is used to lift the engine, injury and damage can occur.

• SEBU8024-03 August 2007 Operation and Maintenance Manual 3512C Oil Well Servicing Engine R1A1-Up (Engine) R3A1-Up (Engine)
  

• SEBU8024-03 13 Safety Section Mounting and Dismounting i01372247 Mounting and Dismounting SMCS Code: 1000; 4450; 7405 Inspect the st eps, th e handho lds, and the wo rk area before mounting the engine. Keep these items clean and keep these items in good repair. Mount the engine and dismount the engine only at locations that have steps and/or handholds. Do not climb on the engine, and do not jump off the engine. Face the engine in order to

• SEBU8024-03 9 Safety Section General Hazard Informatio n When pressurized air and/or pressurized water is used for cleaning, wear protective clothing, protective shoes, and eye protection. Eye protection includes goggles or a protective face shield. The maximum air pressure for cleaning purposes must be below 205 kPa (30 psi) when the air nozzle is deadheaded. The maximum water pressure for cleaning purposes must be below 275 kPa (40

• 8 SEBU8024-03 Safety Section General Hazard Information i02566298 General Hazard Information SMCS Code: 1000; 4450; 7405 g00104545 Illustration 4 Attach a “Do Not Operate” warning tag or a similar warning tag to th e start switch or to th e controls before the engine is serviced or before the engine is repaired. These warning tags (Special Instruction, SEHS7332) are available fro m your Caterpillar dealer. Attach the warning tags to the engine and to each operator control station. When it is appropriate, disconnect the starting co

• SEBU8024-03 5 Foreword California P roposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause canc er, birth defects, and other reproductive harm. Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
  

3-1

Engine Tools

Table of Contents

Air Induction ………………………………………………………………………………………………………………………………………………. 3-3

Cooling System ………………………………………………………………………………………………………………………………………… 3-19

Crankshaft, Main Bearings and Flywheel ……………………………………………………………………………………………….. 3-44

Cylinder Block and Liners ……………………………………………………………………………………………………………………….. 3-77

Cylinder Head, Valves and Cam Followers …………………………………………………………………………………………….. 3-103

Electrical and Ignition Tools ………………………………………………………………………………………………………………….. 3-169

Lube System……………………………………………………………………………………………………………………………………………. 3-175

Engine Test Tools ……………………………………………………………………………………………………………………………………. 3-180

Fuel System Test Tools …………………………………………………………………………………………………………………………… 3-202

Fuel System Repair and Adjust ………………………………………………………………………………………………………………. 3-243

Pistons, Rings and Connecting Rods ……………………………………………………………………………………………………… 3-317

Camshaft and Timing Gear Tools ……………………………………………………………………………………………………………. 3-337

Starting Systems …………………………………………………………………………………………………………………………………….. 3-354

Engine Lifting and Positioning ……………………………………………………………………………………………………………….. 3-356

3600 Engine Tools …………………………………………………………………………………………………………………………………… 3-376

Engine Tools

Contents Summary of Caterpillar Engine Tools Cat Overhaul 3512