Кофемашина miele cva 620 2 инструкция

• Page 1: Operating Instructions

  Operating instructions Built-in automatic coffee machine CVA 620 GWOZi To avoid the risk of accidents or damage to the machine it is essential to read these Operating instructions before it is installed or used for the first time. M.-Nr. 06 492 200…

• Page 2: Table Of Contents

  Contents Description of the machine ……… . 4 Caring for the environment .

• Page 3
  Contents Cleaning and care ……….45 Rinse button .

• Page 4: Description Of The Machine

  Description of the machine External view a Hot water spout b Coffee spouts, height-adjustable c Handle to open machine front d Control dial for steam e Steam spout with milk frother f Drip tray with grilles g Selector switch h Display i Coffee portion buttons j Rinse and pre-warming button…

• Page 5
  Description of the machine Interior view l Coffee bean container m Slide control to select fineness of ground coffee n Slide control to select quantity of ground coffee o Water container p Waste unit q Brew unit Coffee glossary To help you understand the language of coffee, please read the glossary of coffee terms at the end of this instruction book.

• Page 6: Caring For The Environment

  Caring for the environment Disposal of the packing Disposal of your old appliance material or machine The transport and protective packing Electrical and electronic appliances / has been selected from materials which machines often contain materials are environmentally friendly for disposal which, if handled or disposed of and can normally be recycled.

• Page 7: Warning And Safety Instructions

  Warning and Safety instructions Technical safety This machine complies with all Before connecting the machine to relevant legal safety requirements. the mains supply, make sure the Improper use of the machine can, rating on the data plate corresponds to however, present a risk of both the voltage and frequency of the personal injury and material household supply.

• Page 8
  (except when it is been carried out by a suitably qualified combined with a Miele built-in plate engineer. warming drawer). Before the machine is connected, the steam control dial must be in the off position.
• Page 9
  Never place a drink with ignited Only use the descaling tablets alcohol under the steam spouts. supplied by Miele and follow the The flames could ignite plastic instructions on the packet carefully. Use components and cause fire damage.
• Page 10
  Warning and Safety instructions In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the machine and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches and other vermin will not be covered by the guarantee.

• Page 11: Brief Description

  Brief description Unlike standard coffee machines, this If two cups of coffee or espresso are machine has a container for coffee required at the same time, the beans so that they can be freshly appropriate coffee portion button must ground for every cup, to benefit fully be pressed twice.

• Page 12
  Brief description To ensure that the flavour can develop fully and be maintained for longer the machine has an additional function to automatically rinse and pre-warm the system. The same function is used to clean the system and the coffee spouts after use.

• Page 13: Programming The Machine

  Programming the machine The machine can be programmed in easy stages for setting to your exact requirements. The following programming options are available: Language German, Dutch, Portuguese, Spanish, English, Italian, French Rinsing on, off Water hardness hardness 1, hardness 2, hardness 3, hardness 4 Temperature large coffee minimum, low, medium, high, maximum Temperature medium coffee…

• Page 14
  Programming the machine To programme the machine, ^ Turn the selector to the programming position. The machine is now in programming mode and will respond according to the symbols shown under the buttons. ^ By pressing the — or e button –…

• Page 15: Choosing A Language

  Programming the machine Choosing a language The language for the commands in the display can be selected before the machine is used for the first time. ^ Turn the selector anti-clockwise to the programming position. The machine is now in programming mode and will respond according to the symbols shown under the buttons.

• Page 16: Rinsing

  Programming the machine Rinsing To remove any coffee grounds from the system the water piping and brew unit must be rinsed through every day before the first drink is prepared. If programme «Rinsing» is set to «On» rinsing will start automatically when the machine is cold and the selector switch is set to the «On»…

• Page 17: Setting The Water Hardness

  Programming the machine ^ Press the e button to switch rinsing on or off. It is a good idea to set this option to «On» so that the rinse process cannot be forgotten. ^ Press ENTER to save this setting, or turn the selector to «0»…

• Page 18
  Programming the machine ^ Dip the strip in your drinking water for approximately a second, then shake off any excess water. The results will be evident after about 1 minute. If the water is harder than 7.0 mmol/l or 700 mg/l (40 °d), limescale will build up more rapidy than with soft water.

• Page 19: Selecting The Temperature For Drinks

  Programming the machine ^ Press ENTER to confirm this option. The sub-menu will appear in the display as follows: ^ Press the e button to set the water hardness level (hardness 1 — hardness 4) ^ Press ENTER to save this setting, or turn the selector to «0»…

• Page 20
  Programming the machine ^ Press the e button to highlight programming option «Temp. L coffee» for large coffee, «Temp. coffee» for medium coffee or «Temp. S coffee» for small/espresso coffee with an asterisk. A different temperature can be programmed for each drink option.

• Page 21: Switching The Pre-Brewing Function On Or Off

  Programming the machine Switching the pre-brewing function on or When the pre-brewing function is switched on, the freshly ground coffee is first moistened with a little hot water. Then the remaining water is forced through the moistened coffee at high pressure. This pre-brewing process allows the aroma and froth on the coffee to develop to the full.

• Page 22: Switching The Pre-Grinding Function On Or Off

  Programming the machine ^ Press ENTER to save this setting, or turn the selector to «0» to undo the alterations if a mistake has been made. This will bring you back from the sub-menu. When making coffee with the pre-brewing function switched on, the word «Pre-brewing»…

• Page 23: Switching The Programmed Quantity Of Hot Water On Or Off

  Programming the machine ^ Press the e button to switch the pre-grinding function to On or Off. ^ Press ENTER to save this setting, or turn the selector to «0» to undo the alterations if a mistake has been made. This will bring you back from the sub-menu.

• Page 24: Displaying The Number Of Cups Of Coffee Already Dispensed (Total Coffee)

  Programming the machine ^ Press the e button to switch the function to On or Off. ^ Press ENTER to save this setting, or turn the selector to «0» to undo the alterations if a mistake has been made. This will bring you back from the sub-menu. Displaying the number of cups of coffee already dispensed (Total coffee) Select function «Total coffee»…

• Page 25
  Programming the machine ^ Turn the selector anti-clockwise to the programming position. The machine is now in programming mode and will respond according to the symbols shown under the buttons. The following will appear in the display: ^ Press the e button to highlight programming option «Timer»…

• Page 26: System Lock

  System lock The machine can be locked to ensure that it is not operated by unsupervised children or persons who are unacquainted with the operating instructions. Activating the system lock ^ Turn the selector anti-clockwise to the «Lock» position: The following will appear in the display: ^ Press the — button until the following appears in the display: The machine is now locked and cannot dispense.

• Page 27: Filling The Water And Coffee Bean Containers

  Filling the water and coffee bean containers Please clean the machine thoroughly before filling the water container and the coffee bean container, (see «Cleaning and care»). Filling the water container The quality of the water plays an important part in the overall quality of the coffee.

• Page 28
  Filling the water and coffee bean containers ^ Take the lid off and fill the container with cold, clean drinking water up to a maximum of 2 cm below the top. A valve in the base of the container will ensure that no water can escape.

• Page 29: Filling The Coffee Bean Container

  Filling the water and coffee bean containers Filling the coffee bean container Only put roasted espresso or coffee beans in the container. Anything else, including ground coffee will damage the grinder. Do not use coffee beans which have been treated with caramel, sugar or other substances. Do not put drinks containing sugar, or instant coffee in the machine.

• Page 30: Setting The Portion Sizes

  Setting the portion sizes Important: the water piping must be rinsed through and the machine cleaned thoroughly before the first drink of coffee is prepared. Use the rinse button for this, (see «Cleaning and care»), and then prepare hot water afterwards, (see «Preparing drinks»).

• Page 31: Coffee And Espresso Cups

  Setting the portion sizes Coffee and espresso cups ^ Turn the selector clockwise to the In Operation position (with or without lighting). If the machine is still cold the display will show the following messages in succession: «Fresh water?» to remind you to fill the water container with cold, fresh drinking water.

• Page 32: Tea Cup

  Setting the portion sizes Warning: Leave the cup under the spouts for a few seconds after the coffee has been dispensed to catch any remaining drips. ^ The procedure is the same for the other two coffee portion buttons. The volumes of water programmed in will now be dispensed every time.

• Page 33
  Setting the portion sizes ^ Place a tea cup under the hot water spout. ^ Press the hot water button d until the cup is as full as required. Then release the hot water button There will be a few seconds delay before water is dispensed.

• Page 34: Making Coffee

  Making coffee Important: the water piping must be rinsed through every day and the machine cleaned thoroughly before the first drink of coffee is prepared. This will take place automatically if the Rinsing programme is set to «On» and the machine is cold.

• Page 35
  Making coffee The following will appear in the display: Wait until the following appears in the display: Pre-warming cups The smaller the volume of coffee/espresso, the more important it is to pre-warm the cup. ^ Place the cup under the hot water spout. ^ Press the hot water button d and half fill the cup.

• Page 36: Small/Espresso, Medium Coffee, Large Coffee

  Making coffee ^ Press ENTER again to confirm your selection. Hot water will be dispensed from both spouts, warming the system. The following will appear in the display: ^ Place the empty, pre-warmed cup under both coffee spouts and prepare the coffee. Small/espresso, medium coffee, large coffee The size of portion dispensed by each of the coffee…

• Page 37
  Making coffee If the selector is already in this position with the message «Standby. . . » shown in the display, the machine is in energy-saving mode. Press ENTER to switch it into operation. The following will appear in the display: Wait until the following appears in the display: ^ Place a cup under both coffee spouts.

• Page 38: To Prepare Two Cups Simultaneously

  Making coffee Cancelling preparation ^ To cancel the coffee making process, press one of the coffee portion buttons and preparation will be stopped immediately. To prepare two cups simultaneously ^ Place a cup under each of the coffee spouts. ^ Press the required coffee portion button in quick succession to bring up two cups g in the display.

• Page 39: Cappuccino

  Making coffee Cappuccino To make cappuccino you need a china or porcelain cup, a large container such as a milk jug and milk. Cold, low-fat milk (1.5% fat) is best for creating froth and ideally it should be prepared in a cold, stainless steel jug that narrows towards the top.

• Page 40
  Making coffee ^ Position the steam spout just below the surface of the milk in the jug and slowly turn the steam control dial anti-clockwise. ^ Move the jug in circles until a thick froth has built up, then lower the spout deeper into the milk to heat the rest.

• Page 41: Hot Water

  Making coffee Hot water When it is switched on, the machine will dispense hot water at any time for tea or other drinks. ^ Turn the selector clockwise to the In Operation position (with or without lighting). If the selector is already in this position with the message «Standby.

• Page 42: After Use

  Making coffee After use Before switching the machine off for any length of time, the water pipes, brew unit and spouts should be cleaned to remove any residual coffee. Place a suitable container under the spouts. ^ Press the rinsing and pre-warming button e. The following will appear in the display: ^ Press ENTER again to confirm your selection.

• Page 43: Programming The Coffee Grinder

  Programming the coffee grinder A good espresso with a thick, even froth depends not only on the quality, pressure and temperature of the water and the quality of the coffee beans, but also on the quantity of beans and how finely they are ground.

• Page 44: Setting The Quantity

  Programming the coffee grinder To alter the grinder setting ^ push the upper slide control to the left (for finer grinding) or to the right (for coarser grinding). You should be able to feel the notches clearly when moving the slide control. If the slide refuses to move, ^ close the machine and dispense a cup of espresso coffee.

• Page 45: Cleaning And Care

  Miele. Failure to do so can result in poor quality coffee, bacterial contamination and in extreme cases can lead to malfunction of the machine.

• Page 46: Water Container

  Wipe dry with a soft cloth. E-Cloth A microfibre «E-Cloth» is available from the Miele UK Spare Parts Department, which is suitable for cleaning surfaces such as stainless steel, glass, plastic and chrome without the use of chemicals.

• Page 47: Stainless Steel Fronted Machines

  Stainless steel surfaces can be cleaned using a proprietary non-abrasive cleaning agent designed specifically for use on stainless steel, or with the Miele E-Cloth. When descaling the machine wipe up any spillages of descaling agent immediately! To help prevent re-soiling, a proprietary conditioning agent for stainless steel can also be used.

• Page 48: Stainless Steel Coloured Controls

  Cleaning and care Stainless steel coloured controls The controls may suffer discolouration or damage if soiling is left on them for too long. Remove any soiling straight away. – Do not use stainless steel cleaners on the controls. When descaling the machine wipe up any spillages of descaling agent immediately! Aluminium fronts Aluminium is affected by the way that light falls on it,…

• Page 49: Drip Tray

  Cleaning and care Drip tray At the rear of the drip tray is a float which will protrude from the drip tray when it is full. Remove the tray and empty and clean it. However, to avoid a build-up of odours, the drip tray should be cleaned every day.

• Page 50: Waste Unit

  Cleaning and care Waste unit Clean the waste unit daily to prevent coffee grounds from turning mouldy. There will probably also be water in the waste unit left over from the rinsing process. Lining the waste unit with one or two pieces of kitchen paper towel will make it easier to clean.

• Page 51: Brew Unit

  Cleaning and care If the «Empty waste unit» message appears in the display window after you have just cleaned the unit out you will need to take it out of the machine and push it back into position again and then press the ENTER button.

• Page 52: Cleaning The Steel Filters

  Cleaning and care ^ Grasp the brew unit by the handle and press the part marked PRESS with your thumb. ^ Carefully pull the brew unit out. If this can only be done with difficulty, it is not correctly positioned, (see «Problem solving guide»).

• Page 53: Lubricating The Brew Unit

  ^ Smear a little of the silicone lubricant supplied on the joints a, in the axle b on the runners c and on sealing ring d. Replacement tubes of silicone lubricant are available to order from your Miele Dealer or from the Spare Parts Dept.

• Page 54: Rinsing Cycle: Degreasing The Brew Unit

  These have been specially formulated for use in this coffee machine. They are available from your Miele Dealer or from the Miele Spare Parts Department. To remind you to degrease the brew unit the message «Rinsing Cycle»…

• Page 55
  Cleaning and care ^ Place a container, minimum capacity 0.75 litres, under both coffee spouts. ^ Press the rinsing and pre-warming button e. (The machine must be operational and heated up, otherwise it will not react when the buttons are pressed.) The following will appear in the display: ^ Press the e button to highlight programming…

• Page 56: Milk Frother

  Cleaning and care Milk frother Always clean the steam spout immediately after use, as it is harder to clean once milk has dried on. ^ Loosen the upper locking ring a and pull the steam spout cover downwards b. ^ Clean the cover with a mild solution of hot water and washing up liquid or in the dishwasher, then dry it.

• Page 57: Descaling

  For descaling you should only use the descaling tablets supplied. These have been specially formulated for use in this coffee machine. They are available from your Miele dealer or the Miele Spare Parts Department. Other types of descaling agents will damage the machine and affect the taste.

• Page 58: To Run The Descaling Programme

  ^ Open the front of the machine. ^ Remove the water container, and fill it with 2 litres of warm water (max. 50°C). Then dissolve 2 Miele descaling tablets in it. ^ Shut the lid of the water container and replace it in the machine.

• Page 59
  Descaling ^ Place a large container (approximately 1 litre) under the steam spout and turn the steam control dial anti-clockwise. The descaling process will commence automatically. The following will appear in the display: During the descaling programme do not open the front of the machine or turn the selector to «0».
• Page 60
  Descaling The following will appear in the display: The machine must now be rinsed out to remove all traces of the descaling agent. ^ Rinse the water conainer out thoroughly and then fill it with at least 2 litres of fresh, cold water and place it back in the machine.

• Page 61: Display Messages

  Display messages The machine has an electronic safety system that reports any problems in the display. Most faults are easily recitifed. Message Cause + Effect Remedy Fill coff. beans The coffee bean container is empty. Fill the container with coffee beans. Ready for use The machine is only dispensing hot water and steam.

• Page 62: Problem Solving

  ^ Check that the fuse is not defective and that the mains fuse has not blown. If it has, consult the Miele Service department..the lighting does not come on when the selector is turned to “In Operation with lighting”…

• Page 63
  Problem solving ^ Disconnect the machine from the mains. Switch off at the wall and withdraw the plug from the socket, or disconnect the mains fuse or remove the screw-out fuse in countries where this is applicable. ^ Open the front of the machine. ^ Insert a small screwdriver in the opening and carefully push it upwards a.
• Page 64
  Problem solving ^ Call the Service department..the coffee grinder makes less noise than usual. The coffee bean container is empty. A message will soon appear in the display. ^ Wait until the grinder makes no noise at all, then refill the bean container with beans.
• Page 65
  Problem solving . . . coffee is not dispensed, even though the beans have been ground and there is sufficient water in the water container. ^ Check whether the slide control for the fineness of the coffee is at the finest setting or if the slide control for the amount of coffee to be ground has been set at the largest amount.
• Page 66
  Problem solving . . . the heating-up time is getting longer, the amount of water coming through is incorrect and the machine is not performing properly. The machine needs descaling..no water comes out of the coffee spouts. The steel filters are dirty.
• Page 67
  Problem solving . . . the brew unit cannot be removed. The brew unit can only be removed when the waste unit has been taken out. If the brew unit is still not removable, then it is not in the right position. ^ Close the door and switch the machine on.

• Page 68: After Sales Service

  In the event of a fault which you cannot correct yourself, or if the machine is under guarantee, please contact: – Your Miele Dealer – The Miele Service Department (see back cover for address). When contacting the Service Department, please quote the model and serial number of your machine.

• Page 69: Electrical Connection U.k., Za, Irl

  Electrical connection U.K., ZA, IRL All electrical work should be carried out by a suitably qualified and competent person only, in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.

• Page 70
  Electrical connection U.K., ZA, IRL Non-rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted).

• Page 71: Electrical Connection Aus, Nz

  Electrical connection AUS, NZ All electrical work should be carried out only by a suitably competent person, in strict accordance with national and local safety regulations. The machine is supplied with a mains cable with moulded plug for connection to a 230 — 240 V mains supply.

• Page 72: Installation

  The coffee machine is designed to be built into a Miele tall unit. * only for AUS, NZ: ³ 520 mm It can also be combined with other Miele built-in appliances. If the coffee machine is to be built in above another appliance, there must be a full-width, closed shelf between them (except when it is combined with a built-in plate warming drawer).

• Page 73
  Installation The machine can also be incorporated in a mobile unit which is available to purchase.

• Page 74: Installation

  Installation Installation Ensure power is not supplied to the machine while installation work is being carried out. The same applies should the machine ever be taken out of the housing unit. The coffee machine must be built in to be operated.

• Page 75: Adjusting The Hinges

  Adjusting the hinges When fitting a door to the machine, or fitting it into a Miele tall unit, the hinges on the machine and the housing unit can be adjusted for alignment. ^ To adjust the door in direction a, turn screw a.

• Page 76: Glossary

  Glossary Arabica is a high quality coffee bean. It Caffeine- the caffeine content of is long and flat with a groove running espresso is only a third or a half the around it. The caffeine content is caffeine normally found in coffee. The stronger the roast, the less caffeine the approximately 0.8 — 1.3%.

• Page 77
  Glossary Espresso lungo is the larger, less Quantity — the quantity of ground coffee concentrated version served in a used for each cup can be set between standard coffee cup. 6 and 9g per cup, depending on taste. Generally 6 to 7g are used for a cup of Espresso ristretto is a double espresso, but there are no absolute strength, bitter tasting espresso.
• Page 80
  Alteration rights reserved / 4904 M.-Nr. 06 492 200 / 00 CVA 620…

Инструкция кофемашины Miele CVA 620

Информация отображена на картинке

Информация отображена на картинке

Информация отображена на картинке

Информация отображена на картинке

Miele CVA 620 инструкция по эксплуатации
(80 страниц)

Operating instructions

Built-in automatic coffee machine CVA 620

To avoid the risk of accidents or damage to the machine

it is essential to read these Operating instructions before

it is installed or used for the first time.

External view

a Hot water spout

b Coffee spouts, height-adjustable

c Handle to open machine front

d Control dial for steam

e Steam spout with milk frother

f Drip tray with grilles

g Selector switch

h Display

i Coffee portion buttons

j Rinse and pre-warming button

k Hot water button

Description of the machine

Interior view

l Coffee bean container

m Slide control to select fineness of ground coffee

n Slide control to select quantity of ground coffee

o Water container

p Waste unit

q Brew unit

Coffee glossary

To help you understand the language of coffee, please read the glossary of coffee terms at the end of this instruction book.

Warning and Safety instructions

In countries where there are areas which may be subject to infestation

by cockroaches or other vermin, pay particular attention to keeping the machine and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches and other vermin will not be covered by the guarantee.

Disposal of your old machine

Before throwing an old machine away, switch it off and disconnect it

from the power supply. Cut off the cable directly behind the machine, then cut off the plug and render it useless to prevent misuse.

The manufacturer cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

To ensure that the flavour can develop fully and be maintained for longer the machine has an additional function to automatically rinse and pre-warm the system. The same function is used to clean the system and the coffee spouts after use.

Hot water from the hot water spout can be used to pre-warm the cups.

The machine can be programmed to switch to standby mode so it is always ready for operation but does not consume unnecessary electricity. This can be programmed to happen between 15 minutes and 3 hours after coffee was last dispensed.

To save time when preparing coffee for a number of people, the pre-grind function can be selected, so there is always a portion of coffee ready.

Programming the machine

The machine can be programmed in easy stages for setting to your exact requirements. The following programming options are available:

Language German, Dutch, Portuguese, Spanish,

English, Italian, French

Rinsing on, off

Water hardness

hardness 1, hardness 2, hardness 3, hardness 4

Temperature large coffee

minimum, low, medium, high, maximum

Temperature medium coffee minimum, low, medium, high, maximum

Temperature small/espresso coffee minimum, low, medium, high, maximum

Pre-brewing on, off, long

Pre-grinding off, on

Programme hot water off, on

Total coffee number of coffee portions

Descaling automatic descaling programme

Standby timer to switch off time, selectable in 15 minute stages

A more detailed explanation of the programme options is given in the individual sections.

Programming the machine

To programme the machine,

^Turn the selector to the programming position. The machine is now in programming mode and will respond according to the symbols shown under the buttons.

^ By pressing the — or e button

–the required programming option in the display can be highlighted with an asterisk. Press ENTER to select the option.

–the settings of the various programming options can be altered.

–a time can be entered for the Standby option.

^ By pressing ENTER

–a programming option highlighted with an asterisk can be selected.

–an alteration to the programmed settings can be saved.

If a setting is altered by mistake, do not

press ENTER. Turn the selector to position «0». The altered setting will not

be saved and the original setting will be retained.

Programming the machine

Choosing a language

The language for the commands in the display can be selected before the machine is used for the first time.

^ Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

Programming option «Language» will be highlighted with an asterisk.

^ Press ENTER to confirm this option.

The sub-menu will appear in the display as follows:

^ Press the e button until the required language appears (deutsch, nederlands, portugues, espanol, english, italiano or francais).

^ Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

All commands in the display will now appear in the selected language.

Programming the machine

Rinsing

To remove any coffee grounds from the system the water piping and brew unit must be rinsed through every day before the first drink is prepared. If programme «Rinsing» is set to «On» rinsing will start automatically when the machine is cold and the selector switch is set to the «On» position, with or without lighting. This will warm the brew unit up at the same time because hot water is used for the rinse process. An appropriate message will appear in the display.

If a drink has just been prepared the machine will still run an automatic rinse programme shortly before it goes into standby mode.

To prevent water from running into the

drip tray always place an empty cup under the coffee spouts before making

the first cup of coffee.

^Turn the selector anti-clockwise to the programming position. The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following message will appear in the display:

^Press the e button to highlight programming option «Rinsing» with an asterisk.

^Press ENTER to confirm this option.

The sub-menu will appear in the display as follows:

Programming the machine

^ Press the e button to switch rinsing on or off.

It is a good idea to set this option to «On» so that the rinse process cannot be forgotten.

^ Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

Setting the water hardness

For trouble-free operation of the coffee machine, and to ensure that the descaling reminder appears in the display at the appropriate time, it is important to programme in the water hardness. The water hardness indicates how much calcium is dissolved in the water. The higher the calcium content, the harder the water is.

The machine monitors the volume of water passing through it in conjunction with the hardness of the water. Less hard water can be allowed to pass through before descaling than soft water.

The local water authority will be able to tell you the hardness of water in your area. Alternatively, you can measure the hardness yourself using the enclosed test strip:

Programming the machine

^Dip the strip in your drinking water for approximately a second, then shake off any excess water.

The results will be evident after about 1 minute.

If the water is harder than 7.0 mmol/l or 700 mg/l (40 °d), limescale will build up more rapidy than with soft water. Descaling will need to be carried out more regularly than stated to prevent limescale damage to the machine.

Use programming option «Water hardness» to programme in the water hardness.

There are four programmable levels:

^Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

Press the e button to highlight programming option «Water hardness» with an asterisk.

Programming the machine

^ Press ENTER to confirm this option.

The sub-menu will appear in the display as follows:

^ Press the e button to set the water hardness level (hardness 1 — hardness 4)

^ Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

Selecting the temperature for drinks

The machine can be set at different temperatures to suit varying coffee drinking habits.

Five temperature levels are available for each drink option. Maximum is the highest temperature, minimum the lowest.

Not all types of coffee can withstand a

high temperature. Certain types are too delicate and the froth on top would not

be so good.

^ Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

Programming the machine

^Press the e button to highlight programming option «Temp. L coffee» for large coffee, «Temp. coffee» for medium coffee or «Temp. S coffee» for small/espresso coffee with an asterisk.

A different temperature can be programmed for each drink option.

^Press ENTER to confirm this option.

Depending on the programming option selected, the sub-menu will appear in the display as follows:

^Press the e button to set the temperature to minimum, low, medium, high or maximum.

^Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

Programming the machine

Switching the pre-brewing function on or off

When the pre-brewing function is switched on, the freshly ground coffee is first moistened with a little hot water. Then the remaining water is forced through the moistened coffee at high pressure. This pre-brewing process allows the aroma and froth on the coffee to develop to the full.

When the pre-brewing function is switched off, the hot water is forced through the coffee immediately.

^ Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

^ Press the e button to highlight programming option «Pre-brewing» with an asterisk.

^ Press ENTER to confirm this option.

The sub-menu will appear in the display as follows:

^ Press the e button to switch the pre-brewing process on, off or to «long» (an extra long pre-brew).

Programming the machine

^Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

When making coffee with the pre-brewing function switched on, the word «Pre-brewing» will appear in the display after the coffee has been ground.

Switching the pre-grinding function on or off

When the pre-grinding function is switched on, a new portion of beans will be ground immediately each time a cup is prepared, so there is always a portion of ground coffee in readiness. This saves time and is particularly useful when making coffee for a number of guests. To prevent loss of aroma, however, the pre-grinding function should be switched off when only preparing coffee occasionally.

^Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

^Press the e button to highlight programming option «Pre-grinding» with an asterisk.

^Press ENTER to confirm this option.

The sub-menu will appear in the dislay as follows:

Programming the machine

^ Press the e button to switch the pre-grinding function to On or Off.

^ Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

Switching the programmed quantity of hot water on or off

If the function «Prog. hot water» is switched on, the machine will dispense a precise, pre-programmed quantity of hot water when the hot water button d is pressed. (See «Setting the portion sizes»). When the function is switched off, the machine will dispense hot water freely if the hot water button d is pressed, and continue to do so until the button d is pressed again.

^ Turn the selector anti-clockwise to the programming position.

The machine is now in programming mode and will respond according to the symbols shown under the buttons.

The following will appear in the display:

^ Press the e button to highlight programming option «Prog. Hot water» with an asterisk.

^ Press ENTER to confirm this option.

The sub-menu will appear in the display as follows:

^Press the e button to switch the function to On or Off.

^Press ENTER to save this setting, or

turn the selector to «0» to undo the alterations if a mistake has been made.

This will bring you back from the sub-menu.

Displaying the number of cups of coffee already dispensed (Total coffee)

Select function «Total coffee» and press ENTER to display the number of cups of coffee (small/espresso, medium coffee, large coffee) that have been dispensed to date. Press ENTER again to bring you back from the sub-menu.

Setting a standby time

To ensure that the coffee machine does not consume unnecessary electricity and yet is always ready for operation, it can be switched to energy-saving mode via programming option «Timer». The lighting also switches off in energy-saving mode.

The length of time before it switches to this mode can be programmed in. This can be between 15 minutes and 3 hours. The time is measured from the last time coffee/water was dispensed.

Whenever the selector is turned to «0» or

the machine front is opened, the

machine will begin to calculate the time again.