Kramer allrad 380 руководство по ремонту

  • Contents

  • Table of Contents

  • Troubleshooting

  • Bookmarks

Quick Links

Operator’s Manual

Wheel loaders

/

Models

From serial nos.

Edition

Order number

Language

/

351-01 / 351-02 / 351-03

351 01 0001 / 351 02 0001 / 351 03 0001

1.0

1000245584

EN

loading

Summary of Contents for Kramer 380

  • Page 1
    Operator’s Manual Wheel loaders Models 351-01 / 351-02 / 351-03 From serial nos. 351 01 0001 / 351 02 0001 / 351 03 0001 Edition Order number 1000245584 Language…
  • Page 2
    – without prior permission in writing from the manufacturer. No reproduction or translation of this publication, in whole or part, without the written consent of KRAMER-WERKE GmbH. Any infringement of legal provisions, in particular of those regarding copyright protection, shall be subject to civil and criminal law prose- cution.

  • Page 3: Table Of Contents

    Table of contents Table of contents Table of contents Declaration of conformity EC declaration of conformity (model 351-01) …………EG-1 EC declaration of conformity (model 351-02) …………EG-2 EC declaration of conformity (model 351-03) …………EG-3 Introduction General information on the Operator’s Manual …………1-1 Abbreviations/symbols ………………

  • Page 4
    Table of contents Warning of special hazards ………………2-12 Electric energy ………………..2-12 Gas, dust, steam, smoke …………….. 2-12 Hydraulics ………………….2-13 Noise …………………… 2-13 Oil, grease and other chemical substances …………. 2-13 Battery ………………….2-13 Tyres …………………… 2-13 Operation Description of control elements …………….
  • Page 5
    Table of contents Drive interlock with code input (option) …………..3-20 Keyboard for entering codes: overview …………3-20 Entering/changing the personal code ………….. 3-21 Enabling the drive interlock …………….3-21 Disabling the drive interlock …………….3-22 Putting the drive interlock out of operation …………3-22 Putting the drive interlock back into operation again ……..
  • Page 6
    Table of contents Electric connection – front socket (option) …………. 3-42 Putting the front socket into operation …………. 3-42 Machine lights ………………….3-43 Machine lights operation ……………… 3-43 Working lights operation …………….. 3-44 Interior light operation ………………3-44 Signalling system ………………..3-45 Turn indicator operation ……………….
  • Page 7
    Table of contents Continuous operation of the 3rd control circuit (option) ……… 3-64 Continuous operation of the 3rd control circuit ……….3-64 Emergency lowering of loader unit in case of diesel engine breakdown ….3-65 Lowering or raising ………………3-65 Pressure relief on the quickhitch couplers ………….
  • Page 8
    Table of contents Load hook (option) ………………..3-93 Safety instructions regarding work with a load hook ……..3-93 Working with the automatic bucket repositioning (option) ……..3-94 General information on automatic bucket repositioning ……..3-94 Front/rear hydraulic additional control circuit (option) ……….3-95 Connections for additional control circuits (overview) ……..
  • Page 9
    Table of contents Hydraulic system ………………..5-14 Safety instructions regarding maintenance of the hydraulic system ….5-14 Monitoring the hydraulic oil and the reflux filter ……….5-15 Checking the hydraulic oil level …………… 5-16 Filling up hydraulic oil ………………5-16 Important information for the use of biodegradable oil ……..
  • Page 10
    Table of contents Maintenance of attachments and of the work equipment ……..5-36 Maintenance of the automatic trailer coupling (option) ………. 5-37 Cleaning and lubricating the trailer coupling ………… 5-37 Check the trailer coupling for wear …………..5-37 Maintenance: diesel particle filter (option) …………. 5-38 Checking the electronic filter monitoring …………
  • Page 11
    Table of contents Payloads …………………… 6-15 Loader unit with bucket ………………6-15 Loader unit with pallet forks …………….6-15 Loader unit with pallet forks (foldable fork arms option) ……..6-16 Loader unit with load hook (option) …………..6-16 Trailer weight/drawbar load for automatic trailer coupling (option) ….6-16 Wheel loader dimensions with bucket (model 351-01) ……….
  • Page 12
    Index Index Index Symbole “Hose burst valve” safety feature (option) …….3-98 Emergency lowering of the loader unit with the engine stopped …………….3-65 Engine Abbreviations/symbols ……………1-1 Avoiding running the engine under low-load conditions ..3-17 Accelerator pedal …………..3-34 Check the engine oil …………5-5 Accelerator pedal lock –…
  • Page 13
    Index Pivots and hinges …………..5-36 Screw connections …………5-36 Legal regulations ……………1-8 Service and maintenance work at regular intervals …5-32 Licence, identification …………..1-8 Trailer couplings …………..5-37 Light system …………….3-43 Tyre care …………….5-24 Load diagram …………….3-89 V-belt ……………..5-13 Load hook (option) …………..3-93 Maintenance of the air conditioning system ……5-27 Load on trailer coupling (option) ……….6-16 Maintenance plan …………..5-47…
  • Page 14
    Index Hydraulic ram protection …………6-6 Lift, tilt and push-out ram velocity ……..6-6 Safety instructions …………..2-1 Noise levels ……………6-12 3rd control circuit on control lever (joystick) ……3-63 Pilot control …………….6-5 Applications with lifting gear ……….2-8 Steering system …………..6-4 Battery …………….2-13 Tightening torques ………….6-13 Electric energy …………..2-12 Tyres for models 351-02/351-03 ……..6-11 Gas, dust, steam, smoke ………..2-12…
  • Page 15
    Index Telltales ………………3-6 Tilt ram lock (option) …………..3-98 Trailer coupling (option) Operation …………….3-99 Transport position Pallet forks ……………..3-28 Transporting loads with the pallet forks ……..3-92 Type labels and component numbers ……..1-10 Tyres ………………5-24 Warning identification …………..1-9 Washer system …………….3-49 Tank ………………3-49 Wheel loader warranty ……………1-4 Working…

  • Page 16: Ba 35101/02/03 En — Ausgabe 1.0 * Ba_35101_02_03_10_Ensix.fm

    Index I-14 BA 35101/02/03 EN — Ausgabe 1.0 * BA_35101_02_03_10_enSIX.fm…

  • Page 17: Ec Declaration Of Conformity (Model 351-01)

    EC declaration of conformity (model 351-01) Manufacturer Kramer-Werke GmbH Wacker-Neuson-Str. 1 D-88630 Pfullendorf Product Machine designation Model/version 351-01 (380) Serial number 351 01 _ _ _ _ _ Output kW Measured sound power level dB(A) 100.3 Guaranteed sound power level dB(A) Conformity assessment procedure The following inspection body was involved in the procedure: Fachausschüsse Bau und Tiefbau (Notified body number (EU): 0515)

  • Page 18
    EC Declaration of Conformity EC declaration of conformity (model 351-02) Manufacturer Kramer-Werke GmbH Wacker-Neuson-Str. 1 D-88630 Pfullendorf Product Machine designation Model/version 351-02 (480) Serial number 351 02 _ _ _ _ _ Output kW 45 (58 optional) Measured sound power level dB(A) 100.3…
  • Page 19
    EC Declaration of Conformity EC declaration of conformity (model 351-03) Manufacturer Kramer-Werke GmbH Wacker-Neuson-Str. 1 D-88630 Pfullendorf Product Machine designation Model/version 351-03 (580) Serial number 351 03 _ _ _ _ _ Output kW Measured sound power level dB(A) 100.3…

  • Page 20: Ec Declaration Of Conformity (Model 351-01

    EC Declaration of Conformity EG-4 BA 35101/02/03 EN – Edition 1.0 * 35101_02_03_EG_Konformität.fm…

  • Page 21: Introduction

    Introduction Introduction Introduction 1.1 General information on the Operator’s Manual This Operator’s Manual applies to the wheel loaders model 351-01/351-02 and contains important information on how to work safely, correctly and economically with the machine. Therefore, it aims not only at new operators, but it also serves as a reference for experi- enced ones.

  • Page 22: Machine Outside View

    Introduction 1.3 Machine outside view Fig. 1: Machine outside views Pos. Description Pos. Description Headlight with turn indicator Reflectors Rearview mirror Rear hooks for loading/tying down the machine (left/right) Front working light Towing facility Eye hook (for removing the cab) Socket (oil and fuel preheater option) Protective FOPS screen (option) Additional fuel tank filler inlet (option)

  • Page 23: Models And Trade Names: Overview

    Introduction 1.4 Models and trade names: overview Wheel loader model Trade name 351-01 351-02 351-03 1.5 Brief description of the wheel loader General information on the machine According to German traffic regulations and the German agricultural and forestry tractors provision, the model 351-01/351-02/351-03 wheel loaders are self-propelled work machines, tractors or equipment carriers.

  • Page 24: Hydrostatic Drive

    Introduction Hydrostatic drive The diesel engine permanently drives a hydraulic pump (variable displacement pump), whose oil flow is sent to a hydraulic motor flanged on the gearbox. The force of the hydrau- lic motor is transmitted to the rear axle via the transfer gearbox. At the same time, the front axle is driven by the cardan shaft, ensuring permanent 4 wheel drive.

  • Page 25: Fields Of Application And Using A Wheel Loader With An Attachment

    In order to avoid damage to the machine, only the attachments listed in the table have been authorised for installation on the machine. Mounting attachments other than Kramer is only allowed if they correspond to the description in chapter “Operation”, “Equipping the machine with a…

  • Page 26
    Introduction Wheel Part no. Dimensions ISO 7546 capacity Description of attachment loader (model) mm (in) struck/heaped m³ 1750 (68.90) 1000187786 with teeth 351-01 0,55/0,65 1000187787 1750 (68.90) without teeth Grading, removing and scraping 1850 (72.83) vegetation, for example; picking up 1000187296 with teeth and evenly spreading material;…
  • Page 27
    Introduction Wheel Part no. Dimensions ISO 7546 capacity Description of attachment loader (model) mm (in) struck/heaped m³ 351-01 351-02 1000050660 3000 (118.11) – Material pusher For moving loose bulk material 351-03 351-03 1000100759 4000 (157.48) – 351-01 Digging and transporting nursery Tree replanter 351-02 1000100840…

  • Page 28: Legal Regulations Regarding Wheel Loader Operation

    Introduction 1.8 Legal regulations regarding wheel loader operation General safety instructions Danger! Transporting accompanying persons in the cab, on the wheel loader or in/on the attachments is not allowed! Before leaving the seat, also apply the parking brake and stop the diesel engine! Driving or operating the wheel loader outside the operator’s compartment is not allowed!

  • Page 29: Machine Inspections

    Introduction Machine inspections When operating the machines, the national safety regulations must be followed as well, for instance in Germany, the regulations for accident prevention “Deutsche Prüfstelle für Land- und Forsttechnik” (DPLF German inspection and certification body for agriculture and forestry) and the accident prevention regulation “Fahrzeuge (vehicles)” (BGV D29 § 57 clause 1).

  • Page 30: Type Labels And Component Numbers

    Introduction 1.9 Type labels and component numbers Serial number The serial number is stamped on the machine frame A (next to the axle attachment, on the right in driving direction). It is also located on type label B on the machine frame at the front right (on the side of the loader unit bulkhead).

  • Page 31: Variable Displacement Pump Number

    Introduction Variable displacement pump number The type label (arrow) is located on the hydraulic pump housing (next to where the pump is installed on the diesel engine) Fig. 5: Hydraulic pump type label Variable displacement motor number The type label (arrow) is located on the hydraulic motor, on the right in driving direction. Fig.

  • Page 32: Description Of Labels And Symbols

    Introduction 1.10 Description of labels and symbols Labels on the outside of the machine Cab eye hook label The eye hooks on the cab are for removing the cab only and may not be used for crane handling the machine –…

  • Page 33
    Introduction Explanation of “Book” symbol The “Book” symbol on a label means that the indications are explained in further detail in the Operator’s Manual. Location On labels. Fig. 14: Explanation of “Book” symbol Label: Danger of shearing! Caution! Do not touch any moving or turning parts! Carry out inspections and maintenance work only at engine standstill! Location In the area of the engine cooling (V-belt guard)

  • Page 34: Labels Inside The Cab

    Introduction Labels inside the cab Label: load diagram (A) for pallet forks and tyre pressure table The framed weight indications state the maximum authorised load on the fork arms for industrial and offroad applications. The maximum load varies according to the distance between the load centre and the rear end of the pallet forks.

  • Page 35
    Introduction Brake fluid label A = Caution! Do not fill in any water! B = Use only LHM brake fluids! • – see chapter 5 “Maintenance of the brake system” on page 5-23 • – see chapter 5 “Fluids and lubricants” on page 5-43 Location Fig.
  • Page 36
    Introduction Label: No transport of persons! Warning! Lifting or transporting persons on the wheel loader, in the bucket or on the pallet forks is prohibited. Location Inside the cab, on right side of front window. Fig. 23: Prohibitive label: no transport of persons Label: No other persons allowed in the cab! Warning! Carrying or transporting accompanying persons in the cab or on the wheel loader is not allowed!

  • Page 37: Labels In The Engine Compartment

    Introduction Labels in the engine compartment Label: Container under pressure, danger of burns! The container is hot and under pressure. Do not open the container as long as it is still hot. Open the container only after the coolant has cooled down Open the cover carefully and slowly to allow the pressure to escape.

  • Page 38
    Introduction Notes: 1-18 BA 35101/02/03 EN – Edition 1.0 * 35101_02_03b110.fm…

  • Page 39: Safety Instructions

    Safety instructions Safety instructions Safety instructions 2.1 Identification of warnings and dangers Important indications regarding the safety of the staff and the machine are identified in this Operator’s Manual with the following terms and symbols: Danger! Failure to observe the instructions identified by this symbol can result in personal injury or death for the operator or other persons.

  • Page 40: Designated Use And Exemption From Liability

    Safety instructions 2.2 Designated use and exemption from liability • Carrying or transporting accompanying persons in the cab or on the wheel loader is not allowed! Carrying or transporting persons in the attachments (e.g. bucket, pallet forks) is not allowed either! •…

  • Page 41: General Conduct And Safety Instructions

    Safety instructions 2.3 General conduct and safety instructions Organisational measures • The machine has been designed and built in accordance with state-of-the-art standards and the recognised safety regulations. Nevertheless, its use can constitute a risk to life and limb of the user or of third parties, or cause damage to the machine and to other material property! •…

  • Page 42
    Safety instructions • Never make any modifications, additions or conversions to the machine and its super- structures (e.g. cab, loader unit etc.), as well as to the attachments, which might affect safety without the approval of the manufacturer! This also applies to the installation and the adjustment of safety devices and valves, as well as to welding work on load-bearing elements! •…

  • Page 43: Selection And Qualification Of Staff, Basic Responsibilities

    Safety instructions Selection and qualification of staff, basic responsibilities • Any work on or with the machine must be carried out by reliable staff only. Do not let unauthorised persons drive or work with the machine! Observe statutory minimum age limits! •…

  • Page 44: Safety Instructions Regarding Operation

    • No raising, lowering or carrying persons in the work equipment/attachments! • Installing a man basket or a working platform is prohibited! (Always contact Kramer-Werke GmbH for installation!) • When crossing underpasses, bridges and tunnels, or when passing under overhead lines always make sure there is enough clearance! •…

  • Page 45
    Safety instructions • Avoid any operation that might be a risk to machine stability! • During operation on slopes, drive or work uphill or downhill. If driving across a slope cannot be avoided, bear in mind the tilting limit of the machine! Always keep the attachments/work equipment close to the ground.

  • Page 46: Applications With Lifting Gear

    Safety instructions Applications with lifting gear Definition: Applications with lifting gear are understood as procedures involving raising, transporting and lowering loads with the help of slings and load-securing devices (e.g. ropes, chains). In doing so, the help of persons is necessary for securing and detaching the load. This applies for example to raising and lowering pipes, shaft rings or containers! •…

  • Page 47: Trailers And Attachments

    Safety instructions Trailers and attachments • Prior to driving on public roads remove all attachments which cannot be secured in compliance with the legal regulations of your country! • Get informed on the legal regulations of your country which deal with the use and appli- cations of trailers towed by the machine! •…

  • Page 48: Safety Instructions For Maintenance

    Safety instructions 2.5 Safety instructions for maintenance • Avoid any operational mode that might be prejudicial to safety! • Observe the adjustment, maintenance and inspection activities and intervals set forth in the Operator’s Manual, including information on the replacement of parts/partial equipment! These activities may be carried out by technical staff only! •…

  • Page 49
    Safety instructions • Have loads fastened and crane operators instructed by experienced persons only! The person giving the instructions to the operator must be within sight or sound of him! • Always use specially designed or otherwise safety-oriented ladders and working platforms to carry out overhead assembly work.

  • Page 50: Maintenance Work On Protective Rops And Fops Structures

    Safety instructions 2.6 Maintenance work on protective ROPS and FOPS structures Cab, roll-over bar, protective screen • Straightening and welding work on cabs, roll-over bars and protective screens are prohibited. These structures must be replaced by original spare parts from the manufacturer! •…

  • Page 51: Hydraulics

    Safety instructions Hydraulics • Work on the hydraulic equipment of the machine must be carried out only by persons having special knowledge and experience in hydraulic systems! • Check all lines, hoses and screwed connections regularly for leaks and obvious damage! Repair any damage and leaks immediately! Splashed oil can cause injury and fire! •…

  • Page 52
    Safety instructions Notes: 2-14 BA 35101/02/03 EN – Edition 1.0 * Sicherheit_Radlader.fm…

  • Page 53: Operation

    Operation Operation Operation 3.1 Description of control elements This chapter describes the controls, and contains information on the function and the handling of the telltales and controls in the cab. The pages stated in the table refer to the description of the controls. A combination of digits, or a combination of digits and letters (e.g.

  • Page 54: Cab Overview

    Operation 3.2 Cab overview Inside of cab (overview) For more information see page Sun visor Board – relays and fuses (left) …………………………Front window wiper motor …………………………3-49 Interior light …………………………….3-44 Front working light…………………………..3-43 Board – relays and fuses (right) …………………………Steering column adjustment lever………………………..

  • Page 55
    Operation Instrument panel overview: see overleaf Instrument panel overview: see overleaf BA 35101/02/03 EN – Edition 1.0 * * 35201_02b310.fm…

  • Page 56: Instrument Panel, Multifunctional Lever And Drive Lever (Overview)

    Operation 3.3 Instrument panel, multifunctional lever and drive lever (overview) Indicating instrument console For more information see page Not assigned Hydraulic oil temperature gauge ……………………….5-16 Telltale (red/yellow/green) – diesel particle filter (option) ………………..5-36 Telltale (green) – front socket (option) ……………………..3-42 Telltale (yellow) –…

  • Page 57
    Operation Operation Indicating instrument For more information see page Hour meter Right/left turn indicators telltale (green) for rear attachments ………………..3-45 Right/left turn indicators telltale (green) ……………………..3-45 Coolant level telltale (red) …………………………5-9 Hydraulic oil filter telltale (red) ……………………….5-16 Air filter telltale (yellow) …………………………5-11 Alternator charge function telltale (red) ……………………..5-32…

  • Page 58: Functional Description: Telltales

    Operation 3.4 Functional description: telltales Telltale check All telltales come on briefly for a check when the ignition is switched on. Caution! For your own safety and in order to avoid consequential damage to the machine, have defective telltales immediately checked or replaced by an authorised workshop! Telltales and warning lights on the indicating instrument Engine oil pressure telltale (red)

  • Page 59: Telltales And Indicators On The Instrument Panel

    Operation Parking brake telltale (red) Comes on when the parking brake is applied. The electric driving interlock prevents starting the engine with the parking brake applied. Hydraulic oil filter telltale (red) Indicates inadmissibly high pressure in the hydraulic reflux line to the tank. In this case: ☞…

  • Page 60
    Operation Telltale (yellow) – hose burst valve/load stabiliser (option) Indicates that the load stabiliser is switched on, and that the hose burst valve is disabled. ➥ – see Load stabiliser (option) on page 3-40 and “Hose burst valve” safety feature (option) on page 3-98 Telltale (red) –…

  • Page 61: Putting The Wheel Loader Into Service

    Operation 3.5 Putting the wheel loader into service Safety instructions regarding commissioning • Only use the steps and handles when entering and leaving the cab • Face the machine as you enter and leave it • Never use the controls or movable lines and cables as handles •…

  • Page 62: Checklist

    Operation 3.6 Checklist These checklists cannot claim to be exhaustive; they are merely intended as an aid for you in fulfilling your duties as a conscientious operator. The checking and monitoring jobs listed below are described in greater detail in subse- quent chapters of the Operator’s Manual.

  • Page 63: Operation Checklist

    Operation Operation checklist After starting the engine and during operation, check and observe the following points: No. Operation checklist ✔ Telltales for engine oil pressure and alternator gone out? (➠ 3-16) 2 Braking effect sufficient? (➠ 3-35) 3 Temperature gauge for engine coolant in normal range? (➠ 3-6) 4 Steering system working properly? (➠…

  • Page 64: Cab

    Operation Operation 3.7 Cab Safety instructions regarding cab entrance and exit • Remove dirt (oil, grease, earth, snow and ice) from handles, footholds and shoes before entering the cab • Use only the machine footholds, platforms and handles for entering the cab •…

  • Page 65: Securing An Open Door In The Arrester

    Operation Securing an open door in the arrester ☞ Press the door against bracket 31 of the arrester until it engages with an audible click Important! Lubricate arrester 31 regularly! Fig. 40: Securing an open door ☞ Release the door out of the arrester: •…

  • Page 66: Engine Cover Lock

    Operation 3.8 Engine cover lock Opening/closing the engine cover Danger! Caution, turning parts! ☞ Stop the diesel engine before opening the engine cover ☞ Open the engine cover: • Stop the diesel engine and remove the ignition key • Press lock A Fig.

  • Page 67: Putting The Diesel Engine Into Operation

    Operation 3.11 Putting the diesel engine into operation Preparing to start the engine Danger! The wheel loader may be put into service only if the operator is seated on the seat! ☞ Operate the machine from the seat only ☞ Prepare to start the engine as follows: •…

  • Page 68: Starting The Engine

    Operation Starting the engine The ignition lock is located on the right-hand side control lever console. ☞ Apply the parking brake to the last notch ☞ Turn the ignition key (preheating start switch 19) to position “1” ☞ The following telltales must come on •…

  • Page 69: Avoiding Running The Engine Under Low-Load Conditions

    Operation Avoiding running the engine under low-load conditions Caution! The running performance of the engine can be negatively affected if it runs at high speed and at less than 20 % of the load. Operating temperature is not reached! • Effects: Increased lube oil consumption •…

  • Page 70: Battery Master Switch (Option)

    Operation 3.12 Battery master switch (option) Battery master switch operation Battery master switch A is located in the engine compartment at the upper left above the variable displacement pump (drive) ☞ Interrupting power supply • Turn and remove the key of the battery master switch (notched position) ☞…

  • Page 71: Enabling (Locking) The Drive Interlock

    Operation Enabling (locking) the drive interlock ☞ Apply the parking brake ➥ – see Parking brake on page 3-36 ☞ Stop the engine ☞ Remove the ignition key (blue) ➥ The drive interlock is enabled in 30 seconds Caution! The drive interlock remains disabled if the ignition key (blue) is not removed from the ignition lock! Disabling (releasing) the drive interlock Start and stop the engine exactly as described on page 3-16 “Starting the engine”.

  • Page 72: Drive Interlock With Code Input (Option)

    Operation 3.14 Drive interlock with code input (option) Keyboard for entering codes: overview The drive interlock is enabled or disabled with “personal” codes entered via the keypad. Two codes are available: • The existing unchangeable six-digit main code for disabling the drive interlock, for entering a personal code or for changing the personal code •…

  • Page 73: Entering/Changing The Personal Code

    Operation Entering/changing the personal code In order to enter or modify the personal code, disable the drive interlock by entering the main code (6 digits) and pressing the (*) key ☞ Turn the ignition key to 1 ➥ The LED comes on for 2 seconds ☞…

  • Page 74: Disabling The Drive Interlock

    Operation Disabling the drive interlock ☞ Enter the personal code or main code (6 digits). ☞ Press the (*) key. ➥ Confirmation: 2 long acoustic signals and long LED flashing ➥ LED OFF = drive interlock is disabled ➥ Diesel engine can be started The diesel engine will not start if a wrong code has been entered ➥…

  • Page 75: Putting The Drive Interlock Back Into Operation Again

    Operation Putting the drive interlock back into operation again ☞ Press the (*) key for 2 seconds (ignition key in position OFF) until two short acoustic signals are given for confirmation ➥ The system is enabled again. The code must be entered to start the engine. Interruption of drive interlock power If the drive interlock was enabled before electric power was interrupted, short acoustic sig- nals are given upon switching on the keypad (similar to those that are given when entering…

  • Page 76: Oil And Fuel Preheater (Option)

    Operation 3.15 Oil and fuel preheater (option) General information on the oil and fuel preheater • Connect the oil and fuel preheater only to an earthed socket • Check the connecting cable regularly for damage • Replace a damaged cable by a new one immediately •…

  • Page 77: Jump-Starting The Engine (External Battery)

    Operation 3.16 Jump-starting the engine (external battery) Safety instructions regarding external starting aids Caution! The jump lead connected to the positive (+) terminal of the starting battery must never be brought into connection with electrically conductive vehicle parts – danger of short circuit! ☞…

  • Page 78: Before Moving Off

    Operation 3.17 Before moving off Special instructions for driving on public roads • Carrying or transporting accompanying ersons in the cab or on the wheel loader is not allowed • The machine is subject to the applicable national legal regulations (e.g. StVZO German road traffic regulations) and to the provisions laid down in the General Certification for Vehicles (Germany) or the data confirmation (Germany).

  • Page 79: Bucket Transport Position

    Operation Bucket transport position Important! Loader unit operation – see Loader unit control lever (overview) on page 3-62 ☞ Set the bucket to transport position as follows: • Empty and tilt back the bucket B 308b0350.eps • Raise the loader unit so that both red marks D on the lift frame and the bulkhead are aligned ➥…

  • Page 80: Transport Position Of Pallet Forks

    Operation Transport position of pallet forks Important! Only pallet forks with foldable fork arms are authorised for travel on public roads! Remove pallet forks that are not authorised for transport on public roads and use a suitable means of transport to move or transport them. •…

  • Page 81: Locking The Control Lever (Joystick) And The 3Rd Control Circuit (Attachments)

    Operation Locking the control lever (joystick) and the 3rd control circuit (attachments) Secure the control lever (joystick) and the 3rd control circuit (quickhitch) against uninten- tional actuation when driving on public roads. ➥ – see Operating and securing the 3rd control circuit on page 3-63 The stop cock for locking the control lever is located on the console of the control lever base (on the right in driving direction).

  • Page 82: Steering System

    Operation 3.18 Steering system Steering column height and angle adjustment (option) Danger! In order to avoid danger of accidents, do not adjust the steering column when driving! ☞ Adjust the steering column at machine standstill as follows: • Stop the wheel loader and the engine •…

  • Page 83: Wheel Synchronisation (Front/Rear Axles)

    Operation 3.19 Wheel synchronisation (front/rear axles) Danger! Do not synchronise the wheels when driving on public roads! ☞ Synchronise the steering system before driving on public roads Synchronisation when starting the machine Wheel synchronisation is automatically set by turning the steering wheel to the left and right when the engine is running.

  • Page 84: Changing Steering Mode

    Operation 3.20 Changing steering mode General safety information on changing steering mode Danger! In order to avoid danger of accidents, do not change steering mode when driving the machine on public roads! Furthermore, do not change steering mode when driving at high speed! ☞…

  • Page 85: Changing Over To Diagonal Steering (Crab Steering Option)

    Operation Changing over to diagonal steering (crab steering option) Use diagonal steering (crab steering) only for moving away laterally from a wall or for repo- sitioning the wheel loader laterally. Danger! In order to avoid danger of accidents, do not drive over longer distances. Furthermore, driving on public roads with diagonal steering (crab steering) is not allowed! ☞…

  • Page 86: Accelerator Pedal

    Operation 3.21 Accelerator pedal Speed control with the accelerator pedal ☞ Accelerator pedal Fig. 30/16 controls the drive speed as follows: • Press the accelerator pedal down ➥ Drive speed is increased • Release the accelerator pedal slowly ➥ Drive speed is reduced •…

  • Page 87: Brake/Inching Pedal

    Operation 3.23 Brake/inching pedal Specific information on brake/inching pedal actuation • The brake/inching pedal is located on the left in the machine. • Dirt accumulation and objects in the area of the brake/inching pedal can result in brake malfunctions. • Keep the brake/inching pedal clean and remove all objects in the area of the pedal Danger! The brake lights at the rear of the machine neither come on when applying the parking brake, nor during inching.

  • Page 88: Parking Brake

    Operation 3.24 Parking brake General instructions regarding the parking brake The parking brake is located to the right of the control lever base. A starting interlock prevents the machine from starting even with the parking brake slightly applied. Important! The driving direction can only be selected if the parking brake is completely released.

  • Page 89: Driving The Machine

    Operation 3.25 Driving the machine Selecting a speed range The machine has two speed ranges. The switch for selecting the speed range is located on the switch console on the right-hand side of the instrument panel. ☞ Select the 1st speed range •…

  • Page 90: Changing Direction (Forwards/Reverse)

    Operation Changing direction (forwards/reverse) Important! For reasons of safety, changing direction (forwards/reverse) during machine travel is only possible if drive speed is reduced to less than 15 kph! ☞ Select the driving direction • Reduce engine speed: remove your foot from the accelerator pedal •…

  • Page 91: Low-Speed Control (Option)

    Operation 3.27 Low-speed control (option) Selecting the drive speed This function is especially useful for operation of hydraulically driven attachments (e.g. rotary broom, rotary hoe) in order to ensure continuous drive speed. Unregulated low-speed control Drive speed is set with potentiometer 93 and maintained by means of the manual diesel engine speed setting (accelerator pedal).

  • Page 92: Load Stabiliser (Option)

    Operation 3.28 Load stabiliser (option) General instructions regarding the load stabiliser function The load stabiliser cushions and dampens the movements of the loader unit. It avoids unstable oscillating movements of the loader and increases drive comfort and safety! Important! Always switch on the load stabiliser when driving on public roads! In order not to impair the load stabiliser function in transport position of the loader unit, do not retract the tilt ram to the limit (pressure)! •…

  • Page 93: Switching The Load Stabiliser On And Off

    Operation Switching the load stabiliser ON and OFF The switch is located on the left on the switch console of the instrument panel Important! Switch on the load stabiliser only in transport position! In order not to impair the load stabiliser function in transport position of the loader unit, do not retract the tilt ram to the limit (pressure)! •…

  • Page 94: Backup Warning System (Option)

    Operation 3.29 Backup warning system (option) Instructions regarding the backup warning system The backup warning system consists of a signal transmitter fitted on the rear of the cab. The signal transmitter generates an acoustic signal when shifting into reverse. The acous- tic level is about 103 dB (A) at a distance of 1 m and at a frequency of 2800 Hz.

  • Page 95: Machine Lights

    Operation 3.31 Machine lights Machine lights operation The switch for the machine lights is located on the switch panel on the left-hand side of the instrument panel. Side marker light operation Function Press switch 68 to the 1st position B Telltale in switch comes on OFF Press switch 68 down to position A Telltale in switch goes out Low beam operation…

  • Page 96: Working Lights Operation

    Operation Working lights operation Danger! Switch off the working lights to avoid dazzling motorists on public roads! ☞ Do not switch on the working lights when driving on public roads ☞ When operating the machine, only switch on the working lights when no- one can be dazzled by them Function Telltale…

  • Page 97: Signalling System

    Operation 3.32 Signalling system Turn indicator operation Function Telltale RIGHT Push lever 39 forwards R Telltale 76 flashes LEFT Pull lever 39 to the rear L Telltale 76 flashes ➥ Telltale 75 flashes during trailer operation. Caution! The turn indicator system is not in order if telltale 76 flashes about twice as fast as normally! •…

  • Page 98: Cab Heating And Ventilation

    Operation 3.34 Cab heating and ventilation Heating and ventilation system operation The air is guided to the front window by the air vents on the left and right, to two leg room vents and to the rear window by two air vents. ➥…

  • Page 99: Auxiliary Heating (Option)

    Operation 3.35 Auxiliary heating (option) Operating and setting the auxiliary heating At engine standstill, the auxiliary heating warms up the coolant and the cab. Important! Double advantage: warm cab and preheated engine! ☞ Adjust the vehicle heater as follows before setting (programming) the timer: •…

  • Page 100: Heating/Air Conditioning System (Option)

    Operation 3.36 Heating/air conditioning system (option) Heating/air conditioning operation The heating/air conditioning system heats or cools the air in the cab. The control elements for the heating/air conditioning system are located on the switch con- sole on the right (near the door) Important! Close the door and the windows to achieve best air conditioning results.

  • Page 101: Washer System

    Operation 3.37 Washer system Washer system operation Front window wiper Function Turn rotary switch 91 on the lever to Intermittent wipe the first position Turn rotary switch 91 on the lever to Normal wipe the second position Turn rotary switch 91 on the lever Wipers return to base position fully back to 0 Fig.

  • Page 102: Seat

    Operation 3.38 Seat Seat adjustment: overview Always adjust the seat to your individual needs. This will help avoid or minimise physical disorders related to bad posture! Danger! Never change the seat position when driving or working! ☞ Adjust the seat before moving the machine ☞…

  • Page 103: Height Adjustment

    Operation Height adjustment ☞ Raise or lower seat as required until it engages with an audible click Fig. 82: Height adjustment Height adjustment (air-suspension seat, option) The air-suspension seat height can be adjusted continuously ☞ Pull or press lever b (arrow) ➥…

  • Page 104: Horizontal Adjustment With Control Lever Base

    Operation Horizontal adjustment with control lever base ☞ Set fan revs as follows: • Sit down on the seat • Pull lever d up and at the same time • Move the seat forwards or backwards • Allow lever d to engage in required position Fig.

  • Page 105: Seat Belt (Lap Belt)

    Operation 3.40 Seat belt (lap belt) Specific instructions regarding the seat belt Danger! In order to avoid injuries, fasten the seat belt (lap belt) when driving the wheel loader! ☞ Bear in mind the following when fastening the seat belt: •…

  • Page 106: Unfastening The Seat Belt

    Operation Unfastening the seat belt ☞ Unfasten the seat belt as follows: • Hold the seat belt • Press red button C on buckle B ➥ Latch A is released from buckle B by spring action • Slowly return the seat belt to the retractor (option) 30763b0006.eps Fig.

  • Page 107: Other Controls

    Operation 3.41 Other controls Folding back the control lever base Danger! The door on the right can be used as entry and exit. ☞ In order to avoid danger, the following conditions must be fulfilled before entering or leaving the cab: •…

  • Page 108: Towing The Machine

    Operation 3.42 Towing the machine Safety instructions for towing away If the diesel engine and/or the hydraulic drive breaks down, the machine can be towed out of the hazard zone under the following conditions. • The towing vehicle (tractor vehicle) must have enough tractive power and be fitted with a safe brake system! •…

  • Page 109: Towing The Machine

    Operation Towing the machine Danger! In order to avoid danger of accidents, the towing vehicle must have enough tractive power and be fitted with a safe brake system. ☞ Tow away only with a towing bar ➥ See chapter Specifications on page 6-1 for the machine’s dimensions and weights! ☞…

  • Page 110: Decommissioning The Machine Temporarily

    Operation 3.43 Decommissioning the machine temporarily Stopping/parking the machine Danger! Machines parked on slopes can roll away. ☞ Use the parking brake to park the machine safely and to prevent it rolling away – see Parking brake on page 3-36! ☞…

  • Page 111: Crane Handling The Machine

    Operation 3.44 Crane handling the machine Safety instructions regarding crane handling • The crane and the lifting gear must have suitable dimensions ➥ Machine weight – see chapter 6 “Specifications” on page 6-1 • Crane handling requires lifting gear with four ropes, chains, etc. •…

  • Page 112: Loading And Transporting The Machine On A Transport Vehicle

    Operation 3.45 Loading and transporting the machine on a transport vehicle Safety instructions regarding loading on a transport vehicle • The transport vehicle must be of adequate size ➥ – see chapter 2 “Transporting, towing, loading” on page 2-9 ➥ See chapter Specifications, “Machine weights”…

  • Page 113: Loading And Tying Down The Machine

    Operation Loading and tying down the machine ☞ Load as follows: • Secure the transport vehicle with chocks to prevent it from rolling • Place the access ramps at the smallest possible angle • Do not exceed an angle of 20° •…

  • Page 114: Loader Unit Control Lever (Overview)

    Operation Operation 3.46 Loader unit control lever (overview) Control lever (joystick) for lift and tilt rams and 3rd control circuit Danger! Before leaving the seat, and when driving on public roads, lock the control lever (loader unit) and the 3rd control circuit against unintentional actuation! ☞…

  • Page 115: Operating And Securing The 3Rd Control Circuit

    Operation 3.47 Operating and securing the 3rd control circuit Locking and unlocking an attachment from the quickhitch Danger! When working with attachments without hydraulic functions, unintentionally actuating the switch on the control lever (3rd control circuit) can unlock the attachment from the quickhitch! ☞…

  • Page 116: Continuous Operation Of The 3Rd Control Circuit (Option)

    Operation 3.48 Continuous operation of the 3rd control circuit (option) Continuous operation of the 3rd control circuit For hydraulic movements/procedures over a longer period of time or operation of hydraulic motors (e.g. rotary broom) or for operation of a hydraulic attachment with a control valve adjusted to maximum oil flow, with an unpressurised reflux.

  • Page 117: Emergency Lowering Of Loader Unit In Case Of Diesel Engine Breakdown

    Operation 3.49 Emergency lowering of loader unit in case of diesel engine breakdown Lowering or raising ☞ Lower the loader unit as follows: • Make sure no-one is dangerously close to the machine • Apply the parking brake • Slowly push control lever 15 forwards C until the loader unit is fully lowered •…

  • Page 118: Equipping The Machine With A Standard Bucket

    Operation 3.51 Equipping the machine with a standard bucket Fitting a standard bucket onto the quickhitch Danger! Before starting work, make sure the attachment is safely locked onto the quick- hitch by means of the lock ram! ☞ You must be able to see the lock pins on either side (left/right) in the mount- ing bores on the attachment ☞…

  • Page 119: Removing A Standard Bucket From The Quickhitch

    Operation Removing a standard bucket from the quickhitch Danger! In order to prevent the attachment from tipping over, place it on the ground ensuring stability! ☞ Position the attachment so that after unlocking it will stand safely and not tip over ☞…

  • Page 120: Driving On Public Roads With A Standard Bucket

    Operation 3.52 Driving on public roads with a standard bucket Preparing road travel German road traffic regulations prohibit driving on public roads if the distance between the front edge of the bucket and the centre of the steering wheel is over 3500 mm in transport position.

  • Page 121: Working With A Bucket

    Operation 3.53 Working with a bucket Fields of application for bucket • The standard bucket is mainly used for digging earth, and for loosening, picking up, transporting and loading loose or solid materials. • Get informed on the legal regulations of your country which may prohibit driving on public roads with a full bucket! ➥…

  • Page 122: Safety Instructions For Transporting Material In A Full Bucket

    Operation Safety instructions for transporting material in a full bucket Danger! In order to avoid danger of accidents, do not transport loads with a raised loader unit! Always dump in the attachment a little towards the machine, carry it as close as possible to the ground and bear in mind the required ground clearance! If it is dumped in, the bucket is moved parallel to its initial position as the loader unit is raised! If the bucket is unintentionally dumped in to the limit in the raised…

  • Page 123: Loading Loose Material

    Operation Loading loose material ☞ Loading loose material • Align the blade parallel with the ground A • Lower the loader unit to the ground B. To do this: push the control lever forwards C • Drive forwards into the material A ☞…

  • Page 124: Removing Material/Digging In Soft Soil

    Operation Removing material/digging in soft soil ☞ Digging in soft soil • Place the bucket horizontally on the ground B. To do this: push the control lever forwards C Fig. 114: Lowering the loader unit to the ground • Adjust the digging angle 1. To do this: push the control lever to the right B •…

  • Page 125: Removing Material/Digging In Hard Soil

    Operation Removing material/digging in hard soil ☞ Digging in hard soil • Lower the bucket horizontally to the ground 1. To do this: push the control lever forwards C • Adjust the digging angle flatter 2 than for digging in soft soil. To do this: push the control lever to the left A •…

  • Page 126: Loading Heaped Material (Compacted Material)

    Operation Loading heaped material (compacted material) ☞ Loading heaped material (compacted material) • Proceed as for non-compacted material, however when raising the loader unit through the heaped material, dump the bucket slightly in and out (1). To do this: move the control lever alternately to the left and right (A and B) •…

  • Page 127: Fitting A Multipurpose Bucket

    Operation 3.54 Fitting a multipurpose bucket Picking up a multipurpose bucket with the quickhitch Important! The multipurpose bucket is picked up and mounted on the quickhitch in the same way as the standard bucket • – see Fitting a standard bucket onto the quickhitch on page 3-66 Danger! Before starting work, make sure the attachment is safely locked onto the quick- hitch by means of the lock ram!

  • Page 128: Connecting The Hydraulic Lines Of A Multipurpose Bucket To The Wheel Loader

    Operation Connecting the hydraulic lines of a multipurpose bucket to the wheel loader Important! The hydraulic system of the machine is still pressurised even when the engine is not running! The hydraulic quick couplers can be released, however they cannot be re-attached because the pressure in the hydraulic lines has not been released.

  • Page 129: Removing The Multipurpose Bucket From The Quickhitch

    Operation Removing the multipurpose bucket from the quickhitch Danger! In order to prevent the attachment from tipping over, place it on the ground ensuring stability! ☞ Position the attachment so that after unlocking it will stand safely and not tip over Important! The attachment is removed from the quickhitch in the same way as the stand-…

  • Page 130: Driving On Public Roads With The Multipurpose Bucket

    Operation 3.55 Driving on public roads with the multipurpose bucket Preparing road travel German road traffic regulations prohibit driving on public roads if the distance between the front edge of the bucket and the centre of the steering wheel is over 3500 mm in transport position.

  • Page 131: Working With The Multipurpose Bucket

    Operation 3.56 Working with the multipurpose bucket Fields of application for multipurpose bucket • The multipurpose bucket is mainly used for digging earth, and for loosening, pushing, picking up, transporting and loading loose or solid materials. • Get informed on the legal regulations of your country which may prohibit driving on public roads with a full bucket! ➥…

  • Page 132: Safety Instructions For Transporting Material In A Full Multipurpose Bucket

    Operation Safety instructions for transporting material in a full multipurpose bucket Danger! In order to avoid danger of accidents, do not transport loads with a raised loader unit! Always dump in the multipurpose bucket a little towards the machine, carry it as close as possible to the ground and bear in mind the required ground clearance! If it is dumped in, the multipurpose bucket is moved parallel to its initial position…

  • Page 133: Grading And Scraping

    Operation Grading and scraping ☞ Grading • Fold up the front half of the bucket • Set the depth of the layer you want to remove with the lift hydraulics • Set the angle of the rear cutting edge ☞ Drawing material backwards •…

  • Page 134: Pulling Out Material From Slopes

    Operation Pulling out material from slopes This position allows to pull material out of slopes or roadside ditches with maximum safety and to spread it as required. Ansicht_006.iso Fig. 131: Pulling out material with a multipurpose bucket Moving material with longer reach This position allows to move material without damaging slopes or structures.

  • Page 135: Grabbing Bulky Material

    Operation Grabbing bulky material ☞ Grabbing bulky material • The multipurpose bucket allows to safely grab, pick up and transport building timber, reinforcement bars, packaging bands, wire etc. • The multipurpose bucket allows to safely grab, pick up and transport large objects Ansicht_002.iso Ansicht_016.iso Fig.

  • Page 136: Backfilling Round Gravel And Precise Unloading

    Operation Backfilling round gravel and precise unloading ☞ Backfilling round gravel • Precise dosing and placement of pourable material • Bucket teeth move back from the wall as the bucket opens Ansicht_012.iso An sic ht_0 11 .iso Fig. 136: Backfilling and unloading material with a multipur- pose bucket Unloading from the bottom of the bucket for increased dump heights ☞…

  • Page 137: Fitting Pallet Forks

    Operation 3.57 Fitting pallet forks Picking up pallet forks with the quickhitch Important! The pallet forks are picked up and mounted on the quickhitch in the same way as the standard bucket. • – see Fitting a standard bucket onto the quickhitch on page 3-66 Danger! Fig.

  • Page 138: Working With The Pallet Forks

    Operation 3.59 Working with the pallet forks General safety instructions regarding the pallet forks • Follow the special instructions in the Operator’s Manual of the attachment! • Approach the material as closely as possible! • Always approach the material with the machine wheels in straight-ahead position! •…

  • Page 139
    Operation • When driving or working across a slope, the load must be on the uphill side of the machine/attachment. Drive the machine backwards on sloping terrain to prevent the load from falling off and the machine from tilting forwards when braking •…

  • Page 140: Brief Instructions For Fork Arms

    Operation Brief instructions for fork arms The following brief instructions are based on the “Guidelines for testing and repairing fork arms” (© by VETTER Umformtechnik GmbH): • Use fork arms only according to their designated use • Do not exceed the load centre and the load-bearing capacity •…

  • Page 141: Specific Safety Instructions For Picking Up Loads With The Pallet Forks

    Operation Specific safety instructions for picking up loads with the pallet forks • Always lock the control lever for the 3rd control circuit when working with the pallet forks – see Operating and securing the 3rd control circuit on page 3-63. •…

  • Page 142: Adjusting The Fork Arms Of The Pallet Forks

    Operation Adjusting the fork arms of the pallet forks Danger! In order to prevent the fork armss from slipping or sliding sideways, the safety pins of the fork arms must be correctly locked in the notches on the fork frame. ☞…

  • Page 143: Fields Of Application For Pallet Forks

    Operation Fields of application for pallet forks • The pallet forks are mainly used for picking up, transporting and loading palletised material and staple commodities. • Get informed on the legal regulations of your country which may prohibit driving on public roads with loaded pallet forks! ➥…

  • Page 144: Transporting Loads With The Pallet Forks

    Operation Transporting loads with the pallet forks Danger! When transporting loads with the pallet forks raised, the load can fall down or the machine can tilt! ☞ Dump in the pallet forks a little and lower them to transport position ☞…

  • Page 145: Load Hook (Option)

    Operation 3.60 Load hook (option) Safety instructions regarding work with a load hook Shaft rings, containers, pipes etc., can be transported with a load hook and suitable lifting gear (belts, cables, chains). Danger! Observe the following precautionary measures in order to avoid danger of accidents! •…

  • Page 146: Working With The Automatic Bucket Repositioning (Option)

    Operation 3.61 Working with the automatic bucket repositioning (option) General information on automatic bucket repositioning The bucket repositioning function can be used for carrying out cyclical work (e.g. loading trucks) efficiently and with minimum impact to the material: by pressing a button, the attachment is automatically positioned from the dump-out position to the preset work posi- tion (e.g.

  • Page 147: Front/Rear Hydraulic Additional Control Circuit (Option)

    Operation 3.62 Front/rear hydraulic additional control circuit (option) Connections for additional control circuits (overview) For operation of hydraulic front attachments (e.g. rotary broom) or hydraulic rear attach- ments (e.g. salt sprayer, tipping trailer) or hydraulic attachments with additional functions (e.g. snow cutter with hydraulic swivelling ejector). Quick coupler flow rates: ➥…

  • Page 148: Operation Of Front/Rear Additional Control Circuits

    Operation Operation of front/rear additional control circuits Operation of front/rear additional control circuit Operation of front or rear additional control circuit (38 l) The front or rear coupling connections are Set changeover tap D to position V or H enabled Slide the lock on switch 96 downwards and Pressure (38 l) is applied to coupling con- press the switch to position B…

  • Page 149: Additional Control Circuit (4Th Control Circuit Proportional Controls Option)

    Operation 3.63 Additional control circuit (4th control circuit proportional controls option) Operation of 4th control circuit Quick couplers with hydraulic hoses are installed on the loader unit of the wheel loader for the operation of hydraulic attachments with additional hydraulic functions (e.g. high-tilt bucket with clamp).

  • Page 150: Tilt Ram Lock (Option)

    Operation 3.64 Tilt ram lock (option) Switching the tilt ram lock ON and OFF This option is used for securing the tilt ram if it is not supposed to be operated (e.g. when setting down material on high piles). The key-operated switch is located on the switch console on the right (control lever console).

  • Page 151: Automatic Trailer Coupling (Option)

    Operation 3.66 Automatic trailer coupling (option) General information on the trailer coupling Using the automatic trailer coupling is allowed only if the machine has been authorised as a tractor in compliance with § 43 clause 4 of StVZO German road traffic regulations! Please refer to the General Certification for Vehicles (Germany)/the data confirmation or to the registration certificate for the specific requirements regarding attachments (trailers).

  • Page 152: Final Decommissioning Of Machine

    Operation 3.67 Final decommissioning of machine General information on decommissioning If the wheel loader is no longer used according to its designated use, make sure it is decommissioned or taken out of service and disposed of according to applicable regula- tions.

  • Page 153: Troubleshooting

    Troubleshooting Troubleshooting Troubleshooting The information given in this chapter is provided for maintenance staff, for fast and reliable detection of malfunctions and their appropriate repair. Repairs must be carried out by authorised staff. 4.1 Engine trouble Engine trouble Possible causes page Parking brake not applied 3-36…

  • Page 154
    Troubleshooting Engine trouble Possible causes page Oil level too high Fuel grade does not comply with specifications Bleed the fuel system Dirty air filter 5-12 Insufficient engine output Defective air filter maintenance switch or gauge 5-12 Wrong valve clearance – Injection line leaks –…

  • Page 155: Malfunctions In The Air Conditioning System (Option)

    Troubleshooting 4.2 Malfunctions in the air conditioning system (option) Caution! Only authorised workshops and trained staff may carry out repairs, and fill up and empty the air conditioning system! Malfunctions (air conditioning) Possible causes Defective or loose fuse Interrupted line –…

  • Page 156
    Troubleshooting Malfunctions (air conditioning) Possible causes Clogged evaporator Dirty radiator fins Refrigerating-agent line interrupted Loss of refrigerant System leak Clogged fan duct Insufficient refrigerating output Level of refrigerant too low Humidity in system Line interruption, insufficient ground connections or loose contacts in solenoid coil of compressor System cools with interruptions 5-28…

  • Page 157: Maintenance

    Maintenance Maintenance Maintenance 5.1 Important information on maintenance and service work Important information for maintenance personnel Operational readiness and the service life of your wheel loader are heavily dependent on maintenance. Daily and weekly service and maintenance work must be carried out by a specifi- cally trained driver –…

  • Page 158: Fuel System

    Maintenance 5.2 Fuel system Safety instructions for refuelling • Extreme caution is essential when handling fuel – high risk of fire! • Never carry out work on the fuel system in the vicinity of naked flames or sparks! • Do not smoke when working on the fuel system or when refuelling! •…

  • Page 159: Refuelling

    Maintenance Refuelling Danger! In order to avoid intoxication and fire hazards, do not refuel in enclosed areas! ☞ Never carry out work on the fuel system in the vicinity of naked flames or sparks The fuel tank filler inlet is located on the left-hand side of the machine (left-hand side access to cab).

  • Page 160: Bleeding The Fuel System

    Maintenance Bleeding the fuel system Danger! If the fuel, as it drains, comes into contact with hot engine parts or the exhaust system, there is an increased fire hazard! ☞ Never bleed the fuel system if the engine is hot! Bleed the fuel system in the following cases: •…

  • Page 161: Engine Lubrication System

    Maintenance 5.3 Engine lubrication system Safety instructions regarding inspections and maintenance work on the engine Danger! Do not carry out maintenance work on a hot engine! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work Important! Check the oil level every 10 service hours or once a day.

  • Page 162: Filling Up Engine Oil

    Maintenance Filling up engine oil Caution! Too much or incorrect engine oil can result in engine damage! ☞ Do not add engine oil above the MAX mark of the oil dipstick A ☞ Use only the specified engine oil – see Fluids and lubricants on page 5-43 Environment! Use a suitable container to collect the engine oil as it drains and dispose of it in…

  • Page 163: Engine And Hydraulics Cooling System

    Maintenance 5.4 Engine and hydraulics cooling system General instructions regarding cooling system maintenance The combined oil/water radiator cools the diesel engine and the hydraulic oil of the drive and work hydraulics. Caution! Engine temperature should be between 80 and 105 °C. Max.

  • Page 164: Cleaning The Radiator Fins Of The Oil/Water Radiator

    Maintenance Cleaning the radiator fins of the oil/water radiator Danger! Danger of burns! Do not carry out maintenance work on a hot engine and hydraulic system! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work Caution! Dirt on the radiator fins reduces the radiator’s heat dissipation capacity and can cause damage to the engine and the hydraulic system!

  • Page 165: Checking The Coolant Level

    Maintenance Checking the coolant level The coolant expansion tank is located outside on the radiator sheet-metal separation at the rear right. Danger! Danger of burns! Never open the coolant tank and never drain coolant if the warm engine is running since the cooling system is under high pressure! ☞…

  • Page 166: Filling Up Coolant

    Maintenance Filling up coolant Danger! Danger of burns! Never open the coolant tank and never drain coolant if the warm engine is running since the cooling system is under high pressure! ☞ Wait at least 10 minutes after stopping the engine! ☞…

  • Page 167: Air Filter

    Maintenance 5.5 Air filter Checking the air filter for dirt Caution! The filter housing is fitted with a discharge slot E for removing the dust. Bear in mind the following to avoid premature engine wear! ☞ Do not wash, brush or clean the filter cartridge with compressed air ☞…

  • Page 168: Replacing The Air Filter Cartridge

    Maintenance Replacing the air filter cartridge ☞ Change the filter cartridge as follows: • Stop the engine • Prevent the machine from rolling away and remove the ignition key – see chapter 3 “Stopping/parking the machine” on page 3-58 • Open the engine cover •…

  • Page 169: V-Belt

    Maintenance 5.6 V-belt Checking V-belt tension Danger! Caution, turning parts! Only check or retighten/replace the V-belt when the engine is stopped! ☞ Stop the engine before carrying out inspection work in the engine compart- ment! Caution! Cracked and stretched V-belts cause engine damage ☞…

  • Page 170: Safety Instructions Regarding Maintenance Of The Hydraulic System

    Maintenance 5.7 Hydraulic system Safety instructions regarding maintenance of the hydraulic system Danger! Danger of burns! Do not carry out maintenance work on a hot engine and hydraulic system! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work Danger! Hydraulic oil escaping under high pressure can penetrate the skin and cause…

  • Page 171: Monitoring The Hydraulic Oil And The Reflux Filter

    Maintenance Monitoring the hydraulic oil and the reflux filter On the indicating instrument, the red telltale 78 monitors the reflux pressure and the reflux filter, and gauge 41 monitors oil temperature. Caution! Telltale 78 on the indicating instrument comes on if the flow resistance in the reflux filter is too high! ☞…

  • Page 172: Checking The Hydraulic Oil Level

    Maintenance Checking the hydraulic oil level Danger! Danger of burns! Do not carry out maintenance work on a hot engine and hydraulic system! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work ☞…

  • Page 173: Important Information For The Use Of Biodegradable Oil

    – see Fluids and lubricants on page 5-43. Always contact Kramer-Werke GmbH for the use of other products which have not been recom- mended. In addition, ask the oil supplier for a written declaration of guarantee. This guarantee is applicable to damage occurring on the hydraulic components, which can be proved to be due to the hydraulic fluid •…

  • Page 174: Checking Hydraulic Pressure Lines

    Maintenance 5.8 Checking hydraulic pressure lines Safety instructions regarding pressure line checks Danger! Caution when checking hydraulic lines, especially when searching for leaks. Hydraulic oil escaping under high pressure can penetrate the skin and cause serious injuries. ☞ Always consult a doctor immediately, even if the wound seems insignificant –…

  • Page 175: Lubrication Work

    Maintenance 5.9 Lubrication work General safety instructions regarding lubrication work • Park the wheel loader on level ground and prevent it from rolling away by applying the parking brake and placing wheel chocks • Raise the loader unit and secure it with the safety strut on the lift ram •…

  • Page 176: Lubricating The Loader Unit, Lift, Tilt And Lock Rams

    Maintenance Lubricating the loader unit, lift, tilt and lock rams ☞ Lubricate the following lubrication points on the loader unit of the machine: • Lubricate grease nipple C of the tilt ram bearing on the frame every 10 service hours. Lubricate more frequently when in heavy-duty operation •…

  • Page 177: Lubricating With The Central Lubrication System (Option)

    Maintenance 5.10 Lubricating with the central lubrication system (option) General functional description of the central lubrication system The central lubrication system allows you to lubricate all lubrication points of the wheel loader in one single step. • The yellow LED comes on for 1.5 seconds upon switching on ignition to indicate functional readiness of the controls (switch-on check).

  • Page 178: Setting The Lubrication And Break Times

    Maintenance Setting the lubrication and break times Break times and lubrication times are set with the notched switches S and P in the window of the controls. Break time ☞ Remove the red frame on the protective motor housing of the pump with a flat screw- driver to set the time Lubrication time ☞…

  • Page 179: Maintenance Of The Brake System

    Maintenance 5.11 Maintenance of the brake system Specific safety instructions regarding the brake system Brakes are crucial to safety. Incorrect maintenance can cause brake failure. Therefore all repair work on the brakes must be carried out by trained staff. An exception to this is the following work which must be carried out by the driver/ operator: •…

  • Page 180: Tyres

    Maintenance 5.12 Tyres Daily tyre checks Danger! All repair work on tyres and rims may only be carried out by authorised workshops. Important! Regular inspections of the tyres • Improve operating safety • Increase the service life of the tyres •…

  • Page 181: Wheel Change

    Maintenance Wheel change Danger! Use only the wheels and tyres that have been released for the machine. ☞ – see chapter 6 “Tyres” on page 6-11 ☞ Use suitable assembly tools, such as covering sleeves for the studs, a jack etc. ☞…

  • Page 182: Heating And Ventilation System Maintenance

    Maintenance 5.13 Heating and ventilation system maintenance General instructions regarding the heating system The heating system of the machine is equipped with a fine-dust filter. Clean the filter as required, however replace it every 500 s/h at the latest. Danger! In order to be able to comply with the required safety measures regarding occupational safety and health, defective or dirty fine-dust filters must be replaced by new ones!

  • Page 183: Heating/Air Conditioning System (Option): Maintenance

    Maintenance 5.14 Heating/air conditioning system (option): maintenance General safety instructions regarding the air conditioning system • Maintenance and repair work may be carried out by trained staff only. • Careful when carrying out maintenance and repair work – sharp-edged fins on the condensor and the heat exchanger.

  • Page 184: Daily Functional And Visual Checks Of The Heating And Air Conditioning System

    Maintenance Daily functional and visual checks of the heating and air conditioning system Danger! Do not carry out inspection and maintenance work on a hot engine and heat exchanger! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work ☞…

  • Page 185: Cleaning The Heat Exchanger (Condenser)

    Maintenance Cleaning the heat exchanger (condenser) ☞ Proceed as follows: • Stop the engine • Apply the parking brake • Switch off ignition and remove the ignition key • Remove intake screen A from the counterweight • Remove fastening screws B from the heat exchanger and fold away heat exchanger C •…

  • Page 186: Electrical System

    Maintenance 5.15 Electrical system General instructions Maintenance and repair work on the electrical system (including the battery) may be performed only by trained staff and/or authorised workshops! Safety instructions regarding the electrical system and the battery The battery contains sulphuric acid! This acid must not be allowed to come into contact with the skin, the eyes, clothing or the machine.

  • Page 187: Checking/Replacing The Battery

    Maintenance Checking/replacing the battery The battery is low in maintenance and no fluid needs to be refilled under normal operating conditions. However have the battery checked at regular intervals to make sure the elec- trolyte level is between the MIN and MAX marks. Danger! When charging batteries, as well as during normal operation of batteries, an oxyhydrogen mixture is formed in the battery cells with danger of explosions or…

  • Page 188: Inspection And Maintenance Work On The Electrical System At Regular Intervals

    Maintenance Inspection and maintenance work on the electrical system at regular intervals ☞ Daily checks before operating the machine • – see Maintenance plan on page 5-47 • Is the light system OK? • Is the signalling and warning system OK? •…

  • Page 189: Checking/Replacing Fuses And Relays

    Maintenance Checking/replacing fuses and relays The fuses and switching relays are located on the board under the switch panel. Seen from below. ☞ Checking/replacing fuses or switching relays • Switch off ignition and disconnect the battery leads • Remove knurled screw A from the switch panel on the instrument panel •…

  • Page 190: General Cleaning And Maintenance Work

    Maintenance 5.16 General cleaning and maintenance work Safety instructions regarding general cleaning work Cleaning the machine is divided into 3 separate areas: • Inside the cab • Exterior of the machine • Engine compartment The wrong choice of cleaning equipment and agents can impair the operating safety of the machine on the one hand, and on the other undermine the health of the persons in charge of cleaning the machine.

  • Page 191: Cleaning Inside The Cab

    Maintenance Cleaning inside the cab Caution! Never use high-pressure cleaners, steam jets or high-pressure water to clean inside the cab. ☞ Water under high pressure can penetrate into the electrical system, cause short circuits, damage seals and disable the controls! We recommend using the following aids to clean the cab: •…

  • Page 192: Cleaning The Engine Compartment

    Maintenance Cleaning the engine compartment Danger! Caution, turning parts! Do not carry out maintenance work on a hot engine! ☞ Wait at least 10 minutes after stopping the engine ☞ Wear protective gloves and clothing during maintenance work Caution! The engine must be cold before cleaning it with a water or steam jet ☞…

  • Page 193: Maintenance Of The Automatic Trailer Coupling (Option)

    Maintenance 5.18 Maintenance of the automatic trailer coupling (option) Cleaning and lubricating the trailer coupling Caution! Make sure the coupling pin is engaged in the trailer coupling before cleaning with high-pressure equipment! ☞ Apply a little more grease to the coupling pin and the base ring once clean- ing is over ☞…

  • Page 194: Maintenance: Diesel Particle Filter (Option)

    Maintenance 5.19 Maintenance: diesel particle filter (option) Checking the electronic filter monitoring The functional readiness or errors and malfunctions of the filter are indicated by the telltale 42 (DPF LED display) on the instrument panel and the acoustic warning indicator. Errors are indicated by means of a flashing or continuously lit telltale 42 (see table).

  • Page 195: Maintenance Work «Aggressive Media» (Option)

    Maintenance Maintenance 5.20 Maintenance work “Aggressive Media” (option) The machine is specially protected against corrosion for work in aggressive media (e.g. a saline environment). However, this anticorrosion protection is affected by external factors e.g. dirt, cleaning etc. This is why it only has ongoing effect if checked at regular intervals and renewed or reap- plied as required.

  • Page 196: Measures For Maintaining Anticorrosive Protection

    Maintenance Measures for maintaining anticorrosive protection Safety instructions • When handling chemical substances of any kind, such as solvents, wax etc., observe the specific product-related safety regulations (safety data sheet)! • When using volatile and easily flammable anticorrosive agents and solvents: •…

  • Page 197: Applying The Protective Anticorrosion Coating

    Maintenance Applying the protective anticorrosion coating Bear in mind the following instructions as you apply the anticorrosive wax: Caution! Carefully cover all fastening surfaces and elements to which the anticor- rosive protection may not be applied – see Components coated with anticorrosive wax on page 5-39 •…

  • Page 198
    Maintenance Notes: 5-42 BA 35101/02/03 EN – Edition 1.0 * Aggressive Medien.fm…

  • Page 199: Fluids And Lubricants

    Maintenance Maintenance 5.21 Fluids and lubricants Season/tempera- Component/ application Engine/machine fluid SAE grade Specification Capacities ture HD-C 10W-40; EO1040B About 10.5 l Diesel engine Engine oil with oil filter Year-round (2.77 gal) HD-C 15W-40; EO1540B Gearbox 0.8 l (0.21 gal) Front and rear axle differentials 85 W 90 API GL5 or 4.0 l (1.05 gal)

  • Page 200: Explanation Of Symbols On The Maintenance Label

    Maintenance 5.22 Explanation of symbols on the maintenance label Symbol Explanation Before starting maintenance work, follow the safety instructions in the Operator’s Manual! Before starting maintenance work, read the “Maintenance” chapter in the Operator’s Manual! Carry out a functional check of the light system! Check tyres for damage, pressure and tread depth! Carry out a functional check and synchronise the steering system! Carry out a functional check of the brake system!

  • Page 201: Maintenance Label

    Maintenance 5.23 Maintenance label Location: inside the cab on the rear window 5-45 BA 35101/02/03 EN – Edition 1.0 * 35101_02_03b520.fm…

  • Page 202
    Maintenance Notes: 5-46 BA 35101/02/03 EN – Edition 1.0 * 35101_02_03b520.fm…

  • Page 203: Maintenance Plan

    Work- Operator/driver Workshop shop 5.24 Maintenance plan Work description For service and maintenance work on the attachment, please refer to the operation and maintenance manual of the attachment manufacturer as well. Oil and filter changes, fan bearing ( Carry out the following oil and filter changes (check oil levels after test run): •…

  • Page 204
    Work- Operator/driver Workshop shop 5.24 Maintenance plan Work description For service and maintenance work on the attachment, please refer to the operation and maintenance manual of the attachment manufacturer as well. Other inspection work ( • When using biodegradable oil: drain the condensation water in the hydraulic oil tank ●…
  • Page 205
    Work- Operator/driver Workshop shop 5.24 Maintenance plan Work description For service and maintenance work on the attachment, please refer to the operation and maintenance manual of the attachment manufacturer as well. Lubrication ( (Note: lubricate more frequently when in heavy-duty operation!) •…
  • Page 206
    Work- Operator/driver Workshop shop 5.24 Maintenance plan Work description For service and maintenance work on the attachment, please refer to the operation and maintenance manual of the attachment manufacturer as well. Leakage check ( Check for tightness, leaks and chafing: pipes, flexible lines and screw connections of the following assemblies and components. Rectify if necessary: •…

  • Page 207: Specifications

    Specifications Specifications Specifications 6.1 Models and trade names: overview Wheel loader model Trade name 351-01 351-02 351-03 6.2 Frame Sturdy steel sheet frame, rubber-mounted engine 6.3 Engine Wheel loader Wheel loader Engine models models 351-01/351-02 351-02/351-03 Product Deutz diesel engine Type D 2011 LO4 TD 2011 LO4…

  • Page 208: Drive

    Specifications 6.4 Drive Variable displacement pump/boost pump Variable displacement Wheel loader models Wheel loader model pump 351-01/351-02 351-03 Automotive, infinitely variable hydrostatic axial-piston gear- Design Displacement 45 cm³/rev 60 cm³/rev 20 kph Displacement 60 cm³/rev 30 kph/40 kph (option) Max. operating pressure 450 bar 20 kph Max.

  • Page 209: Axles

    Specifications 6.5 Axles Front axle Wheel loader models 351-01/351-02/351-03 Planetary steering and drive axle, Design rigid screw connection with frame Differential lock Self-locking differential 45 % King-pin inclination 0° Camber 0° Steering angle 40° Toe-in 0 mm Track (distance over hubs) 1400 mm Rear axle Wheel loader models 351-01/351-02/351-03…

  • Page 210: Brakes

    Specifications 6.6 Brakes Service brake Wheel loader models 351-01 / 351-02 / 351-03 Design Foot-operated hydraulic disc brake Front axle input shaft Location (also on rear axle if equipped with 30/40 kph high speed) Special hydraulic fluid based on basic mineral oil (LHM) Brake fluid –…

  • Page 211: Work Hydraulics

    Specifications 6.8 Work hydraulics Hydraulic pump Hydraulic pump Design Gear pump 22.5 cm³/rev Displacement wheel loader model 351-01 50 l/min at 2300 rpm 32 cm³/rev Displacement wheel loader models 351-02/351-03 70 l/min at 2300 rpm Location Variable displacement pump (drive) Control valve 3-fold pilot-control (standard) Max.

  • Page 212: Hydraulic Ram Protection

    Specifications Hydraulic ram protection Wheel loader models 351-01 / 351-02 / 351-03 Hydraulic pump – see Hydraulic pump on page 6-5 Max. operating pressure 240 bar Tilt ram Rod side 270 bar Secondary pressure limiting Base side 100 bar Rod side anticavitation valve Lift ram Secondary pressure limiting Base side 270 bar…

  • Page 213: Usable Consumer Pressure At Additional Control Circuit (Option)

    Specifications Usable consumer pressure at additional control circuit (option) Important! The specified flow rates are available at the front or rear quick couplers. Description of quick coupler connections – see chapter 3 “Front/rear hydraulic additional control circuit (option)” on page 3-95 Model Models Wheel loader…

  • Page 214: Electrical System

    Specifications 6.9 Electrical system Electric units Wheel loader models 352-01 / 352-02 Alternator 12 V 95 A Starter 12 V 2.3 kW Battery 12 V 88 Ah Fuses The fuses are installed on the board under the switch panel. Rated current Symbol Protected circuit…

  • Page 215: Main Fuse Box With Relays

    Specifications Rated current Symbol Protected circuit Instrument panel lights Proportional electronics Cutoff solenoid (diesel engine) Heating, air conditioning (option) Drive electronics – hydraulic pump Additional function solenoid valve Radio, float position, drive interlock (option) Central lubrication system, air-suspension seat, bucket repositioning (option) Socket (cigarette lighter), auxiliary heating High current relay, switching relay preheating and starting, telltale for preheating…

  • Page 216: Relays

    Specifications Relays The relays are mounted on the left and right on the board under the switch panel. Switching Protected circuit relay no. Power supply high current relay Power supply high current relay Reverse driving switching relay Forwards driving switching relay Turn indicator relay Front socket switching relay Differential lock switching relay…

  • Page 217: Tyres

    Specifications 6.10 Tyres Tyres for wheel loader model 351-01 Tyre pressure Wheel rims Tyre size Front Rear Wheel rim Wheel offset 12.5-18 MPT-04 TBL 10 PR 365/70R18EM SPT9 365/70 R18 EM-01 135 B 11 x 18 0 mm 335/80 R18 XZSL 151 A2 340/80 R18 XMCL 375/70R20 MPT 136G AC70 11 x 20…

  • Page 218: Machine Weights

    Specifications 6.11 Machine weights Wheel loader Wheel loader Wheel loader Weight model 351-01 model 351-02 model 351-03 Kerb weight 4300 kg 4900 kg 4920 kg Gross weight rating 6500 kg Front axle weight rating 4000 kg Rear axle weight rating Max.

  • Page 219: Coolant Compound Table

    Specifications 6.14 Coolant compound table Outside temperature Water Antifreeze Up to °C % by volume % by volume – — 10 — 20 — 25 — 35 — 42 Water quality at 20 °C = 6.5 – 8.5 ph/overall hardness 3 – 20 °dGH SeeFluids and lubricants on page 5-43 6.15 Tightening torques, conversion tables General tightening torques…

  • Page 220: Conversion Table: Din Standard — Usa Standard

    Specifications Conversion table: DIN standard – USA standard All indications made without engagement. Volumes 1 litre = 2.1 pts (pints) 1 litre = 1.06 qts (quarts) 1 litre = 0.26 gals (gallons) 1 cm³ (cubic zentimeter) = 0.0611 cu. in. (cubic inches) Lengths 1 mm (millimetre) = 0.03937 in (inches) 1 m (metre) = 3.281 feet…

  • Page 221: Payloads

    Specifications 6.16 Payloads Loader unit with bucket Wheel loader Wheel loader Wheel loader Bucket model 351-01 model 351-02 model 351-03 0.75 m³ according 0.85 m³ according 0.95 m³ according Bucket capacity to ISO to ISO to ISO Tipping load 3507 kg 3650 kg 3750 kg Payload…

  • Page 222: Loader Unit With Pallet Forks (Foldable Fork Arms Option)

    Specifications Loader unit with pallet forks (foldable fork arms option) Wheel loader Wheel loader Wheel loader 500 mm load distance model 351-01 model 351-02 model 351-03 Payload, 2000 kg 2150 kg 2300 kg safety factor 1.25 Payload, 1500 kg 1600 kg 1700 kg safety factor 1.67 Transport position:…

  • Page 223: Wheel Loader Dimensions With Bucket (Model 351-01)

    Specifications 6.17 Wheel loader dimensions with bucket (model 351-01) 45° 50° 1400 1570 2020 1490 1750 5080 Fig. 199: Machine dimensions model 351-01 Dimensions Overall length 5080 mm 2, 3 Overall height 2450 mm 2, 4 Overall height with rotating beacon 2680 mm 2, 5 Overall width without bucket…

  • Page 224: Wheel Loader Dimensions With Bucket (Model 351-02)

    Specifications 6.18 Wheel loader dimensions with bucket (model 351-02) 45° 50° 1400 1710 2020 1490 1950 5280 Fig. 200: Machine dimensions model 351-02 Dimensions Overall length 5280 mm 2, 3 Overall height 2480 mm 2, 4 Overall height with rotating beacon 2710 mm 2, 5 Overall width without bucket…

  • Page 225: Wheel Loader Dimensions With Bucket (Model 351-03)

    Specifications 6.19 Wheel loader dimensions with bucket (model 351-03) 45° 50° 1400 1900 2020 1490 1950 5410 Fig. 201: Machine dimensions model 351-03 Dimensions Overall length 5410 mm 2, 3 Overall height 2480 mm 2, 4 Overall height with rotating beacon 2710 mm 2, 5 Overall width without bucket…

  • Page 226: Wheel Loader Dimensions With Pallet Forks (Models 351-01/351-02/351-03)

    Specifications 6.20 Wheel loader dimensions with pallet forks (models 351-01/351-02/351-03) Fig. 202: Machine dimensions with pallet forks Wheel loader model 351-01 351-02 351-03 Pin height 3065 3250 3250 Pallet height 2800 3000 3000 Dump-in angle in transport 17° position Dump-out angle 85°…

  • Page 227
    KRAMER-WERKE GmbH keep abreast of the latest technical developments and constantly improve their products. For this reason, we may from time to time need to make changes to diagrams and descriptions in this documentation which do not reflect products which have already been delivered and which will not be implemented on these machines.
  • Page 228
    Kramer-Werke GmbH Wacker-Neuson-Str. 1 D-88630 Pfullendorf Tel.: 0080090209020 E-mail info@kramer.de www.kramer.de Order no.1000245584 Language EN…

This manual is also suitable for:

480580

Источник

Note for Owners:

Guidesimo.com webproject is not a service center of Kramer trademark and does not carries out works for diagnosis and repair of faulty Kramer 380 equipment. For quality services, please contact an official service center of Kramer company. On our website you can read and download documentation for your Kramer 380 device for free and familiarize yourself with the technical specifications of device.

More Compact Loader Devices:

  • Woody 115 HD

    Woody Log LoaderOperator’s Manual Models 115 HD — 115 HDT — 125 LPWoody Equipment Inc., 205 rue Commercial, Saint-Odilon-de-Cranbourne, Quebec, Canada G0S3A0T. (418) 464-2748 F. (418) 464-2746 Email: [email protected] <mailto:[email protected]> Website: www.equipementswoody.com <http://www.equipementswoody.com/> Facebook: Équipements Woody …

    115 HD Compact Loader, 28

  • Bush Hog 2297

    © 2011 Alamo Group Inc.$0.002297Published 01/11 Part No. 50069201OPERATOR’S MANUAL BUSH HOG® 2501 Griffin Ave.Selma, AL 36703334-874-2700www.bushhog.comLOADERThis Operator’s Manual is an integral part of the safe operation of this machine and mustbe maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safetyand Operation Instructions contained in this manual befo …

    2297 Compact Loader, 98

  • jcb 3DX Super

    SERVICE MANUALBACKHOE LOADER3DX Super, 3DX Xtra, 4DXEN — 9823/0000 — ISSUE 1 — 01/2018This manual contains original instructions, verified bythe manufacturer (or their authorized representative).Copyright 2018 © JCB SERVICEAll rights reserved. No part of this publication maybe reproduced, stored in a retrieval system, ortransmitted in any form or by any other means,electronic, mechanical, photoco …

    3DX Super Compact Loader, 16

  • Barko 495B — SE

    MachineSerial NumberThe information and illustrations in this manual have been approved as accurate at the time of printing. However, the manual may contain information on options not present on your loader. The right is reserved by Barko Hydraulics,LLC to make changes and improvements in it’s product at anytime without notice or obligation.NOTE: The operating and safety instructions for a …

    495B — SE Compact Loader, 99

  • SDLG LG946L

    WAR N I N G Operators and maintenance persons should read this manual carefully and understand these instructions before use to avoid serious accident. For the convenience of relevant people using this manual, it should be easily accessable and kept in readable condition. Operation & Maintenance Manual LG946LWHEEL LOADERSHANDONG LINGONG CONSTRUCTION MACHINERY CO.，LTD …

    LG946L Compact Loader, 109

Recommended Documentation:
Источник

Damqn

Damqn

Joined
Jun 28, 2013
Messages

437

Likes
212


Support

Administrator
Joined
Sep 16, 2013
Messages

4,627

Likes
147


May 21, 2021

Hi, what models does this cover?

Karma Allrad Technical Manual my friend

Sham335

Joined
May 12, 2021
Messages

3

Likes
0


May 21, 2021

Hi, But there are many models. can you post page 3 as it may have a manual number on it.

Support

Administrator
Joined
Sep 16, 2013
Messages

4,627

Likes
147


May 21, 2021

Hi, But there are many models. can you post page 3 as it may have a manual number on it.

Please check:

2.jpg

3.jpg

Sham335

Joined
May 12, 2021
Messages

3

Likes
0


May 21, 2021

thanks for the pictures.Its for 12 and 16 series models. I have a 20 series.

Источник

User Manuals, Guides and Specifications for your Kramer 380 Compact Loader. Database contains 1 Kramer 380 Manuals (available for free online viewing or downloading in PDF): Operator’s manual .

Источник

Kramer Manuals and Guides:

The main types of Kramer 380 instructions: user guide — rules of useing and characteristics, service manual — repair, diagnostics, maintenance, operation manual — description of the main functions of Kramer 380 equipment, etc.

Most of the instructions, that you can see on the site are uploaded by our users. If you have available a manual or document for Kramer 380, which is currently not on the site or present in a different language version, we ask you to upload your document on website, using the «uploading form» available to all registered users.

Источник

Понравилась статья? Поделить с друзьями:
  • Вормил инструкция по применению цена в украине
  • Руководство по ночным прицелам
  • Типовая инструкция по охране труда для токаря
  • 3 украинский фронт руководство
  • Acs 600 руководство по эксплуатации