Мам 860 инструкция на русском контроллер

• Page 1
  MAM860 (IV) Oil-Free Scroll Air Compressor Controller Operation Manual…

• Page 2: Table Of Contents

  Contents I. Introduction …………………………1 Ⅱ. Description of Keys ………………………. 1 Ⅲ. Status Display and Operation ……………………3 Ⅳ. Viewing Running Parameters ……………………4 Ⅴ. List of User Parameters ……………………..5 Ⅵ. List of Manufacturer Parameters …………………… 8 Ⅶ. Adjustment Parameters ……………………..11 Ⅷ.

• Page 3: Introduction

  1. Introduction I. Introduction Huayuan oil-free scroll air compressors are equipped with a microcomputer controller for intelligent automatic operation of air compressors, including automatic pressure control, real-time display of failure messages, protection shutdown, networking group control, etc. Four lines of text can be displayed on the LCD screen where operators can set parameters and check operating status of compressor via man-machine dialog.

• Page 4
  2. Description of Keys When the air compressor is in standby mode, press this key to start it; Start key In connection mode, the air compressor with a communication address of 1 serves as the host, press this key to start the air compressor, and the connection control starts at the same time.

• Page 5: Ⅲ. Status Display And Operation

  3. Status Display and Operation Ⅲ. Status Display and Operation When the controller is powered on, the following interfaces are displayed: Welcome to Scroll Compressor Display interface after power-on After a delay of 5 seconds, the main interface is displayed as follows: Temperature: 78℃…

• Page 6: Ⅳ. Viewing Running Parameters

  4. Viewing Running Parameters Ⅳ. Viewing Running Parameters Press key to move the black scroll bar to the «Running Parameters» menu, and then press key to enter the next menu: Voltage and Air End Current Total Running Time Current Running Time Maintenance Parameters History Fault Production Date and Number…

• Page 7: Ⅴ. List Of User Parameters

  5. List of User Parameters Ⅴ. List of User Parameters In the first-level menu, press key to move the black scroll bar to the «User Parameters» menu, and then press key to enter the menu below: Pressure and Temperature Preset Language: Chinese Start/Stop Delay Preset User password: ****…

• Page 8
  5. List of User Parameters Level 1 Level 2 Initial Function Menu Menu Value In double-machine mode, if one host is working while Start/Stop Double the other is idle in the system, the system makes the Delay 0002H Rotation working machine rest and the idle machine work when Preset it reaches the preset double rotation time.
• Page 9
  5. List of User Parameters Level 1 Level 2 Initial Function Menu Menu Value Multiple machines are connected as «host» or «slave» Connection Host / for operation, and the host controls the start, stop, Status Slave loading and unloading of the slave according to air pressure.

• Page 10: Ⅵ. List Of Manufacturer Parameters

  6. List of Manufacturer Parameters Ⅵ. List of Manufacturer Parameters Parameters used to store relevant data set by air compressor manufacturers. To view manufacturer parameters, the manufacturer password must be verified. In the first-level menu, press key to move the black scroll bar to the «Manufacturer Parameters» menu, and then press key to enter the menu below: Enter Password…

• Page 11
  6. List of Manufacturer Parameters Initial Parameter Item Function Value Air End 2 000000 hrs Modify the total running time of Air End 2. Time Fault History Enter «8888» and confirm it to clear the fault 0000 Reset history. Temperature When Air End 2 temperature is higher than this set 105℃…
• Page 12
  6. List of Manufacturer Parameters Initial Parameter Item Function Value When the controller detects that the use time of oil filter, oil separator, air filter, lubricating oil, lubricating Warning 0010 grease, and belt exceeds their maximum use time, the Shutdown machine will shut down with a report of «too long warning»…

• Page 13: Ⅶ. Adjustment Parameters

  7. Adjustment Parameters Ⅶ. Adjustment Parameters Adjustment parameters are used to set relevant data of the controller and are not allowed to be viewed and modified by users who are not authorized by the manufacturer. Users need to verify the manufacturer password before viewing the adjustment parameters.

• Page 14
  7. Adjustment Parameters Initial Parameter Item Function Value Used to calibrate Air End 2; For phase A current, enter the standard current value. The Standard controller will calculate the current coefficient based on 0000 Current the division of user input value by current value currently detected and save it.
• Page 15
  7. Adjustment Parameters Parameter Initial Value Function Item When calibrating the temperature, enter the coefficient. Coefficient 1.000 Temperature value displayed on the controller = (sampled temperature value — zero) × coefficient Zero 0000℃ Compensate for the zero deviation of hardware. Display the value of temperature which is sampled and Present calibrated by the controller.

• Page 16: Ⅷ. Operation Authority And Password Management

  8. Operation Authority and Password Management Ⅷ. Operation Authority and Password Management The controller provides multiple password and authority management. Different levels of operation authority are provided based on different levels of password as follows: Password Factory Password Permissions Type Settings －…

• Page 17
  24-Hour Hotline 400-0808-650 Paste dealer information here © Copyright Huayuan Precision Machine (Shenzhen) Co., Ltd. The information in this manual is subject to change without notice. 202006（V1.0） HUAYUAN PRECISION MACHINE (SHENZHEN)CO.,LTD Address: No. 5, Hongkan Road, Yanchuan Community, Yanluo Street, Baoan District, Shenzhen Zip code: 518000 Email:marketing@huayuan-mach.com…

MAM-860

Сообщение

bde-1212 » 23 авг 2018, 08:25

Всем доброго дня. Ищу информацию по контроллеру МАМ860 а точнее заводской код доступа.
Причина в том что на контроллере активирована функция высокого и низкого напряжения. А изменить эти параметры с помощью пароля обычного узера не дает.

Re: MAM-860

Сообщение

engineger » 04 сен 2018, 19:33

Заводской пароль высшего уровня 1688 или 1788