Нашел, забирайте кому надо 
— Сервисный мануал для экспа /дорест/ включая электрические схемы, в HTML
— Сервисный мануал для экспа /рест/ в PDF
— Интересная презентация про платформу пятого эксплорера
drive.google.com/drive/fo…dRkdE0oAFv?usp=share_link
Введение 9
Обеспечение безопасности детей 19
Установка детского сиденья ………………………..23
Детские автокресла-бустеры ……………………….26
Установка детских сидений…………………………26
Замки системы блокировки дверей от открывания детьми ……38
Ремни безопасности 39
Пристегивание ремней безопасности ………………….42
Регулировка высоты ремня безопасности ……………….46
Предупреждающий световой и звуковой сигнал
непристегнутого ремня безопасности ………………….46
Устройство напоминания о необходимости пристегнуть ремень
безопасности ………………………………….47
Техническое обслуживание детских удерживающих устройств
и ремней безопасности ……………………………50
Система персональной безопасности 51
Вспомогательная удерживающая система 53
Надувные подушки безопасности водителя и пассажира ……..55
Система определения занятости сиденья переднего пассажира . . .58
Боковые надувные подушки безопасности ………………61
Боковые занавесы системы надувных подушек безопасности
Safety Canopy ………………………………….63
Датчики удара и предупреждающий индикатор надувной
подушки безопасности ……………………………66
Утилизация надувных подушек безопасности …………….68
Ключи и дистанционное управление 69
Общая информация о радиочастотах ………………….69
Пульт дистанционного управления ……………………70
Ключи ………………………………………70
Замена утерянного ключа или пульта дистанционного
управления ……………………………………75
Содержание 1
Введение
4
Комбинация приборов
14
Контрольные лампы и звуковые сигналы
14
Указатели
21
Центр сообщений
24
Развлекательные системы
64
Система MyFord™
64
Дополнительный входной разъем (Line in)
70
Управление микроклиматом
72
Система отопления и кондиционирования воздуха с ручным
управлением
72
Автоматический контроль температуры
75
Функции сенсорного экрана
82
Обогрев заднего стекла
87
Освещение
91
Фары
91
Управление указателями поворота
97
Замена ламп
99
Органы управления на водительском месте
107
Управление стеклооочистителем/омывателем ветрового
стекла
107
Регулировка рулевого колеса
109
Электростеклоподъемники
114
Зеркала
117
Система контроля скорости
120
Адаптивный круиз-контроль
122
Люк крыши
134
Замки и безопасность
153
Ключи
153
Защита от открывания детьми
163
Противоугонная система
181
Содержание
1
Посмотреть инструкция для Ford Explorer (2021) бесплатно. Руководство относится к категории автомобили, 3 человек(а) дали ему среднюю оценку 9.2. Руководство доступно на следующих языках: английский. У вас есть вопрос о Ford Explorer (2021) или вам нужна помощь? Задайте свой вопрос здесь
Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Ford Explorer (2021).
Как перевести мили в километры?
Где я могу узнать идентификационный номер транспортного средства Ford?
Что такое идентификационный номер транспортного средства (VIN)?
Когда транспортному средству Ford требуется техническое обслуживание?
Когда следует заменять тормозную жидкость на Ford?
В чем разница между топливом E10 и E5?
Одна или несколько дверей не открываются изнутри. Что мне делать?
Автомобильный радиоприемник не включается, что делать?
Инструкция Ford Explorer (2021) доступно в русский?
Не нашли свой вопрос? Задайте свой вопрос здесь
- Manuals
- Brands
- Ford Manuals
- Automobile
- 2002 Explorer
- Manual
-
Contents
-
Table of Contents
-
Bookmarks
Quick Links
Table of Contents
14
22
24
32
47
4
8
8
11
14
18
21
22
23
32
37
38
39
47
47
53
1
Related Manuals for Ford 2002 Explorer
Summary of Contents for Ford 2002 Explorer
-
Page 1: Table Of Contents
Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD Rear seat controls Climate Controls Manual heating and air conditioning Rear window defroster Lights Driver Controls Windshield wiper/washer control Power windows Mirrors Speed control Locks and Security…
-
Page 2
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Transmission operation Roadside Emergencies Getting roadside assistance Fuses and relays Changing tires Jump starting Wrecker towing Customer Assistance The dispute settlement board Utilizing the mediation/arbitration Getting assistance outside the U.S. -
Page 3
Ford Motor Company. Ford may change the contents without notice and without incurring obligation. Copyright © 2002 Ford Motor Company… -
Page 4: Introduction
CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
-
Page 5
Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment We must all play our part in protecting the environment. -
Page 6
Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Brake System Brake Fluid — Non-Petroleum Based AdvanceTrac Hazard Warning Flasher Fuse Compartment Windshield Wash/Wipe Rear Window Defrost/Demist… -
Page 7
Vehicle Symbol Glossary Power Window Lockout Interior Luggage Compartment Release Symbol Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack Low tire warning Introduction Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks… -
Page 8: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK GAGE RPMx1000 CHECK ENGINE CHECK FUEL BRAKE Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
-
Page 9
Instrument Cluster Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated. Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced… -
Page 10
Instrument Cluster Four wheel drive low: Illuminates when four-wheel drive low is engaged. Four wheel drive high: Illuminates when four-wheel drive high is engaged. Anti-theft system: Flashes when the Securilock Passive Anti-theft System has been activated. Speed control: Illuminates when the speed control is activated. -
Page 11: Gauges
GAUGES CHECK GAGE RPMx1000 CHECK ENGINE CHECK FUEL BRAKE Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating.
-
Page 12
Instrument Cluster Odometer: Registers the total kilometers (miles) of the vehicle. Trip odometer: Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. -
Page 13
Instrument Cluster Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. -
Page 14: Entertainment Systems
Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. Power/volume: Press to turn ON/OFF; turn clockwise/counterclockwise to increase/decrease volume. 2. Scan: Press SCAN to move up SCAN the radio frequency band. SCAN automatically finds a station, plays it for five seconds, then moves to the next station. Press again to stop. Tape/CD: Press SCAN to sample tape/CD selections for eight seconds.
-
Page 15
Entertainment Systems 4. Cassette door: Insert the cassette with the opening to the right. 5. Eject: Press to eject the cassette/CD. The radio will resume playing. 6. Tape: Press to start tape play. Press to stop tape during rewind/fast forward. CD: Press to start CD play. -
Page 16
Entertainment Systems 10. Balance: Press BAL; then press to shift sound to the left/right speakers. Fade: Press FADE; then press to shift sound to the rear/front speakers. 11. Memory preset buttons: To set a station: Select frequency band AM/FM1/FM2; tune to a station, press and hold a preset button until sound returns. -
Page 17
18. Select (SEL): Use with Bass, Treble, Balance and Fade controls. 19. Bass: Press BASS; then press to decrease/increase the bass output. Treble: Press TREB; then press to decrease/increase the treble output. 20. Tune: Works in radio mode only. Press TUNE to change frequency down/up. -
Page 18: Am/Fm Stereo With Cd
Entertainment Systems AM/FM STEREO IN-DASH SIX CD RADIO FOR PIONEER SOUND SYSTEM 1. Power/volume: Press to turn ON/OFF; turn to increase or decrease volume levels. 2. AM/FM: Press to select AM/FM frequency band. 3. CD: Press to select CD mode. 4.
-
Page 19
Entertainment Systems 5. Rewind: Press to stop tape during rewind/fast forward. Fast forward: Press to start CD play. With the dual media audio, press CD to toggle between single CD and CD changer play. 6. Seek: Press and release SEEK for previous/next strong station, selection or track. -
Page 20
Entertainment Systems Fade: Press FADE; then press to shift sound to the rear/front speakers. 14. Select: Use with Bass, Treble, Balance and Fade controls to adjust levels. 15. Bass: Press BASS; then press to decrease/increase the bass output. Treble: Press TREB; then press to decrease/increase the treble output. -
Page 21: Rear Seat Controls
Entertainment Systems REAR AUDIO CONTROLS (IF EQUIPPED) The rear seat controls allow the middle seat passengers to operate the radio, tape, CD or CD changer (if equipped). To engage, simultaneously press the memory preset controls 3 and 5. Press again to disengage. 1.
-
Page 22: Climate Controls
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle.
-
Page 23: Rear Window Defroster
To aid in side window defogging/demisting in cold weather: 1. Select 2. Select A/C 3. Modulate the temperature control to maintain comfort. 4. Set the fan speed to HI 5. Direct the outer instrument panel vents towards the side windows To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.
-
Page 24: Lights
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. AUTOLAMP DELAY SYSTEM (IF EQUIPPED) The autolamp sets the headlamps to turn on and off automatically. The autolamp control, located in the interior mirror, may be set to: •…
-
Page 25
Lights High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull the lever toward you to activate. Release the lever to deactivate. PANEL DIMMER CONTROL Move the control up and down to adjust the intensity of the panel lighting. -
Page 26
Lights Headlamp aim adjustment The headlamps on your vehicle can only be vertically adjusted. Your vehicle does not require horizontal aim adjustments. To adjust the headlamps: 1. Park your vehicle on a level surface about 7.6 meters (25 feet) away from a vertical plain surface (3). -
Page 27
5. Locate the vertical adjuster for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust down) or counterclockwise (to adjust up). NOTE: Use a 4 mm socket or box wrench to turn the vertical adjuster control. -
Page 28
Lights To use the reading lamps: • Press the rocker control located near each reading lamp to turn it on. • Press the rocker control again to turn it off. BULBS Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs Do not touch the glass of a halogen bulb. -
Page 29
6. Carefully pull old bulb out of the lamp assembly Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. -
Page 30
Lights Replacing tail lamp/turn/backup lamp bulbs 1. Open the liftgate. 2. Remove the two screws from the lamps assembly. 3. Remove the lamp assembly. 4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly. 5. Carefully pull the bulb straight out of the socket. -
Page 31
Replacing license plate lamp bulbs 1. Remove two screws and the license plate lamp assembly. 2. Remove the bulb socket from the lamp assembly by turning counterclockwise. Install the new bulb(s) in reverse order. Replacing high-mount brakelamp bulb 1. Remove the two screws and lamp assembly from vehicle. 2. -
Page 32: Driver Controls
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: when the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed.
-
Page 33
Driver Controls Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. -
Page 34
Driver Controls CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • Utility compartment with compact disc storage • Auxiliary power point • Cupholders • Ashcup • Removable utility bag (if equipped) • Writing surface with note pad •… -
Page 35
Driver Controls Install a garage door opener (if equipped) The storage compartment can be used to hold a variety of aftermarket garage door openers. To install your garage door opener: 1. Open the storage compartment door. 2. Remove the storage clip and stow it away. -
Page 36
Driver Controls • With a full console: • Without a full console: The maximum current draw of any single power point should not exceed it’s fuse rating, otherwise this will result in a blown fuse. Do not use the the cigarette/cigar lighter element in any power point. Keep power point caps closed when not in use. -
Page 37: Power Windows
POWER WINDOWS Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window. One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully.
-
Page 38: Mirrors
Driver Controls Automatic dimming rear view mirror The autolamp/automatic dimming mirror is equipped with an automatic dimming feature. This feature will change from the normal DELAY AUTOLAMP MAX. state to the non-glare “active” state when bright lights (glare) reach the mirror.
-
Page 39: Speed Control
SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the pedal. Speed control does not work at speeds below 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.
-
Page 40
Driver Controls • If the vehicle speed decreases more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. -
Page 41
• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicles previously set speed. -
Page 42
Driver Controls To vent the moon roof: press and hold the roof must be in the closed position in order to move it into the vent position. To close, press and hold the panel stops moving. The moon roof sliding shade can be opened or closed manually. The glass panel must be closed in order to move the sliding shade. -
Page 43
broadcast antennas. Magnetic or metallic objects place on or in the vehicle may also affect the compass reading. • Adjusting the compass Note: The ignition must be in the ON position. 1. Press and hold the MODE control until “VAR” appears in the display. -
Page 44
Driver Controls POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. -
Page 45
Rewinding the shade With extended use, the cargo shade may lose its spring tension. If this occurs, the shade must be manually rewind. This is a two-person operation. 1. Remove the shade from the vehicle and extend it with the smooth grain facing you. -
Page 46
Driver Controls OPERATING THE LIFTGATE Note: The liftgate can only be opened and closed from the outside of the vehicle. To open the liftgate window: 1. Unlock the liftgate using either the key, power door lock control or the Remote entry key fob. 2. -
Page 47: Locks And Security
KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock Passive Anti-Theft System for more information.
-
Page 48
Locks and Security REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 49
2. Press and release again within three seconds to confirm that all the doors are closed and locked. Note: the doors will lock again, the horn will chirp once and the headlamps will flash. If any of the doors are not properly closed the horn will make two quick chirps. -
Page 50
Locks and Security Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. -
Page 51
KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without using a key. • activate or deactivate the autolock feature. The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. -
Page 52
Locks and Security The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the UNLOCK control on the remote entry transmitter. • the ignition is turned to the ON position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. -
Page 53: Anti-Theft System
The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer.
-
Page 54
Locks and Security Tips: • A maximum of eight keys can be coded to your vehicle. • Only use Securilock keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible. -
Page 55: Seating And Safety Restraints
Seating and Safety Restraints FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to avoid injury in a collision or sudden stop.
-
Page 56
Seating and Safety Restraints Adjusting the front manual seat Pull the lever located at the front edge of the seat to move the seat forward or backward. Release the lever to lock the seat in place. Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. -
Page 57
Seating and Safety Restraints Reclining the seats Pull the lever located on the outside of the seat to recline the seatback. Release the lever to lock the seatback in place. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. -
Page 58
Seating and Safety Restraints Tip Slide Do not drive the vehicle with the tip slide seat unlatched. This may result in loss of vehicle control and severe personal injury. To operate the feature: 1. Lift the seatback control (1) on the side of the seat. -
Page 59
Seating and Safety Restraints Push or pull the head restraint to the desired position. Folding rear seats If the rear seat is equipped with adjustable head restraints, they should be placed in the full down position before folding the seat back down. 1. -
Page 60: Safety Restraints
Seating and Safety Restraints 3. Press down on the top outboard area of the seatback until a click is heard. When you hear the click, the seat is latched. To return the seat to the upright position: • Pull the release handle up to unlatch the seat.
-
Page 61
Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. -
Page 62
Seating and Safety Restraints • This safety belt system has a retractor assembly that is designed to extend the seat belt webbing in a controlled manner. This helps reduce the belt force acting on the user’s chest. BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly automatic locking retractor feature or any other safety belt function is not operating properly when checked according to the procedures in Workshop Manual. -
Page 63
Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. When you hear the clicking sound, the safety belt is now in the automatic locking mode. -
Page 64
Seating and Safety Restraints Front safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place. -
Page 65
Seating and Safety Restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a… -
Page 66
Seating and Safety Restraints BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. -
Page 67
Seating and Safety Restraints Reasons given… “Belts are uncomfortable” “I was in a hurry” “Seat belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” Consider… -
Page 68
Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below. -
Page 69
(if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However,… -
Page 70: Air Bags
This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles.
-
Page 71
Seating and Safety Restraints Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag. -
Page 72
Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the air bag system, increasing the risk of injury. -
Page 73
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the air bag sensors to close an electrical circuit that initiates air bag inflation. -
Page 74
Seating and Safety Restraints • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. -
Page 75
Do not attempt to service, repair, or modify the air bag SRS, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle should always wear their safety belts even when an air bag SRS is provided. -
Page 76
Seating and Safety Restraints The air bag SRS is designed to activate when the vehicle sustains a side impact sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. -
Page 77: Child Restraints
Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labeled as conforming to all applicable Federal motor…
-
Page 78
To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. -
Page 79
Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top… -
Page 80
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride. -
Page 81
(passenger side front and outboard rear seating positions) (if equipped) section in this chapter. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. -
Page 82
Seating and Safety Restraints Children 12 and under should be properly restrained in the rear seat whenever possible. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. -
Page 83
Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. -
Page 84
Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward and back. -
Page 85
Seating and Safety Restraints 3. Locate the correct anchor for the selected rear seating position. 4. Clip the tether strap to the anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. -
Page 86: Driving
Driving STARTING YOUR VEHICLE Positions of the ignition 1. ACCESSORY, electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
-
Page 87
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. -
Page 88
Driving • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: 1. Make sure the parking brake is set. 2. Push the clutch pedal to the floor. • Turn the key to 4 (ON) without turning the key to 5 (START). -
Page 89
Cold starting performance can also be improved by using an engine block heater. Engine block heaters are available as an option and can be obtained from your Ford dealer. Consult the engine block heater section for proper use of the engine block heater. -
Page 90: Brakes
Driving Using the engine block heater (if equipped) An engine block heater warms the engine coolant which aids in starting and heater/defroster performance. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°…
-
Page 91
Even when the ABS is disabled, normal braking is still effective. (If your BRAKE warning lamp illuminates with the parking brake released, have your brake system serviced immediately.) Using ABS When hard braking is required, apply continuous force on the brake pedal;… -
Page 92
Driving If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • an underinflated tire • uneven tire wear •… -
Page 93: Transmission Operation
Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed.
-
Page 94
Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 5–speed automatic transmission (if equipped) Your transmission is equipped with an adaptive learning strategy found in the vehicle computer. -
Page 95
N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five. -
Page 96
Driving MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch A starter interlock prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transmission, make sure the parking brake is set, press the clutch pedal to the floor and put the gearshift in N (Neutral). -
Page 97
Driving Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). You can shift into R (Reverse) only by moving the gearshift lever from left of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse). -
Page 98
4×4 HIGH is selected. • 4WD LOW– illuminates when 4×4 LOW is selected. If these lights illuminate when driving in 2WD, contact your Ford dealer as soon as possible. Electronic shift on the fly 4WD system 2WD — Power to the rear wheels only; used for street and highway driving. -
Page 99
vehicle is moving; this is normal and should be no reason for concern. Refer to Shifting to/from 4X4 LOW for proper operation. Shifting between 2WD and 4X4 HIGH • Move the 4WD control between 2WD and 4X4 HIGH at any forward speed. -
Page 100
Driving accelerator in each gear. Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. -
Page 101
Ford joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”… -
Page 102
Driving When climbing a steep slope or hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces the possibility of the vehicle stalling. If your vehicle does stall, do not try to turn around because your vehicle may roll over. -
Page 103
Maintenance and Modifications Ford strongly recommends that you do not add or removing steering or suspension parts (such as lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment. Do not use aftermarket “lift kits”… -
Page 104
Driving • GVWR (Gross Vehicle Weight Rating): Maximum allowable total weight of the base vehicle, occupants, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. •… -
Page 105
Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type… -
Page 106
Driving • Service your vehicle more frequently if you tow a trailer. Refer to the severe duty schedule in the scheduled maintenance guide. • Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). •… -
Page 107
4×4 w/automatic transmission Rear Maximum Engine axle GCWR — kg ratio (lbs.) 4.0L 4127 (9100) SOHC Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’s load, refer to Vehicle loading in this chapter. Towing a trailer over 1588 kg (3500 lbs.) requires a weight distributing hitch. -
Page 108
Never connect any trailer lighting to the vehicle’s taillamp circuits, because it may damage the electrical system resulting in fire. Contact your local Ford dealership for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required. -
Page 109
Driving while you tow When towing a trailer: • Turn off your speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. •… -
Page 110
• Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician. -
Page 111: Roadside Emergencies
GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week •…
-
Page 112
Roadside Emergencies If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006. -
Page 113: Fuses And Relays
This switch is located in the passenger’s footwell, by the kick panel. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button.
-
Page 114
Roadside Emergencies Standard fuse amperage rating and color Fuse Mini Standard rating fuses fuses Grey Grey Violet Violet Pink Pink 7.5A Brown Brown Blue Blue Yellow Yellow Natural Natural Green Green — — — — — — — — — —… -
Page 115
The fuses are: Fuse/Relay Fuse Amp Location Rating 7.5A 7.5A 7.5A 7.5A 7.5A 7.5A Roadside Emergencies Passenger Compartment Fuse Panel Description Mirrors, Autolamp Cluster, Autolamp. Generic Electronic Module (GEM), Keyless entry, 4×4 Trailer tow right-hand stop/turn lamps Starter Park lamps, Autolamps, I/P dimming, Trailer tow Air bags, Cluster Trailer tow left-hand stop/turn… -
Page 116
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 7.5A — 7.5A 7.5A 7.5A Passenger Compartment Fuse Panel Description Speed control, Anti-lock Brake System (ABS), 4×4, Powertrain Control Module (PCM), Park interlock, Keyless entry Ignition, IPATS Subwoofer Air bags, Climate control, Rear climate control Stop lamps, Speed control, Auxiliary Center High-Mounted… -
Page 117
Fuse/Relay Fuse Amp Location Rating — Power distribution box The power distribution box is in the engine compartment. It contains high-current fuses that protect the main electrical systems from overloads. Note: Always disconnect the battery before servicing high-current fuses. Note: Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. -
Page 118
Roadside Emergencies The high-current fuses are: Fuse/Relay Fuse Amp Location Rating 50A Cartridge fuse — 20A Mini fuse — — 50A Cartridge fuse 30A Cartridge fuse — — — 50A Cartridge fuse — Power Distribution Box Description Fuse Panel Not Used Moonroof Not Used Not Used… -
Page 119
Fuse/Relay Fuse Amp Location Rating 20A Cartridge fuse — — 40A Cartridge fuse 30A Cartridge fuse — — — 10A Mini fuse 15A Mini fuse 20A Mini fuse 25A Mini fuse 10A Mini fuse — — 30A Mini fuse 15A Mini fuse —… -
Page 120: Changing Tires
Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 15A Mini fuse 10A Mini fuse — — — — — — 20A CB — — — — — — — — — — — — CHANGING A FLAT TIRE If you get a flat tire while driving: •…
-
Page 121
Spare tire information The spare tire on your vehicle can be used as a spare tire or a regular tire. With 15” wheels, the wheel ornaments from the original wheel/tire can be used on the spare tire. Your spare tire and tools can be found in the following locations: Tool Location Spare Tire… -
Page 122
Roadside Emergencies To stow the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicle. 3. Install the retainer through the wheel center. 4. Turn the lug wrench clockwise until the tire is in its original position. -
Page 123
To change the tire: Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block both the front and rear of the wheel diagonally opposite the flat tire. For example, if the right front tire is flat, block the left rear wheel. -
Page 124
Roadside Emergencies • Front • Rear… -
Page 125: Jump Starting
To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. •…
-
Page 126
Roadside Emergencies Only connect batteries with the same nominal voltage (12 volts). Use jump leads with insulated clamps and sufficient cross section. Do not disconnect the battery from the vehicle’s electrical system. Suitable jump leads for this purpose can be obtained from your dealer. Note: (+) terminal is larger than the (-) terminal. -
Page 127: Wrecker Towing
For towing, contact a professional towing service or your roadside assistance center. Ford recommends your vehicle be towed with a wheel lift or flatbed. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
-
Page 128: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
-
Page 129
P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business). -
Page 130
5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to… -
Page 131: The Dispute Settlement Board
THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford…
-
Page 132
• The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s). -
Page 133
After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law. -
Page 134: Utilizing The Mediation/Arbitration
UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
-
Page 135: Ordering Additional Owner’s Literature
U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S.
-
Page 136: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C.
-
Page 137: Cleaning
WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
-
Page 138
• Do not use hydrofluoric acid-based or high caustic-based wheel cleaners, steel wool, fuels or strong household detergent. • To remove tar and grease, use Ford Extra Strength Tar and Road Oil Removal (B7A-19520–AA), available from your dealer. ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. -
Page 139
Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use Detail Wash (ZC-3–A). • If tar or grease spots are present, use Ford Extra Strength Tar and Road Oil Removal (B7A-19520–AA). WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleaned regularly. -
Page 140
For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Ford Extra Strength Upholstery Cleaner (E8AZ-19523–AA). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). -
Page 141
FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. -
Page 142
Cleaning Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) (B7A-19520–AA) Ford Extra Strength Upholstery Cleaner (not available in Canada) (E8AZ-19523–AA) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Wheel and Tire Cleaner (ZC-37–A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Car Care Kit (ZC-26) Ford Premium Car Wash Concentrate (F2SZ-19523–WC) -
Page 143: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS • Use the Scheduled Maintenance Guide to track routine service. • Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. • Your dealership can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE •…
-
Page 144: Hood
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle. 2. Go to the front of the vehicle and release the latch located in the center between the hood and the grille. 3. Lift the hood. 4.0L SOHC V6 ENGINE 1.
-
Page 145: Engine Oil
Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Use washer fluid that meets Ford specifications. Check State or local regulations for restrictions on the use of methanol, a common windshield washer fluid additive.
-
Page 146
Maintenance and Specifications 5. Remove the engine oil dipstick and wipe clean. 6. Insert the dipstick fully, then remove it again. 7. If the oil level is low, add enough oil to raise the level to within the acceptable range. Note: Oil levels above the mark indicating full may cause engine damage. -
Page 147: Battery
WSS-M2C205–A. It is also recommended that you use the appropriate Motorcraft oil filter or an equivalent filter meeting the Ford Motor Company specification for your engine. Change your engine oil and filter according to the Scheduled Maintenance Guide. BATTERY Your vehicle has a Motorcraft…
-
Page 148
Maintenance and Specifications Excessive pressure on the end walls of a plastic-cased battery could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with the battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. -
Page 149
Maintenance and Specifications ENGINE COOLANT Checking engine coolant • Check the level of engine coolant when the engine is cold. • The coolant should be at the “cold fill level” or with the “cold fill range” as listed on the engine coolant reservoir. -
Page 150
• Do not add extra inhibitors or additives to the coolant. • Do not use alcohol, methanol or brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). • Do not mix with recycled coolant unless from a Ford-approved recycling process (see Recycled Engine Coolant). Recycled engine coolant •… -
Page 151: Fuel Information
Maintenance and Specifications Follow your community’s regulations and standards for disposing and recycling of automotive fluids. Severe climates If you drive in extremely cold climates: • it may be necessary to increase coolant concentration above 50% but less than 60%. •…
-
Page 152
Maintenance and Specifications • Shut the engine off and extinguish all smoking materials and open flames before fueling. • Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed, call a physician immediately. • Avoid inhaling fuel vapors. •… -
Page 153
Aftermarket products could cause damage to the fuel system and invalidate your warranty. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. -
Page 154
Maintenance and Specifications Running out of fuel Running out of fuel may have an adverse affect on powertrain components. • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. -
Page 155
Maintenance and Specifications Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined. -
Page 156
• Avoid running out of fuel. • Do not turn off your ignition while the vehicle is moving. • Follow your Scheduled Maintenance Guide. • Use Ford Motor Company authorized parts for maintenance replacements or for service. Consult your Warranty Guide for emission warranty information. -
Page 157
Maintenance and Specifications The following signs could indicate a problem with your emission control system: • Fluid leaks • Strange odors • Smoke • Loss of engine power • Illumination of the charging system, temperature, or “Check Engine” light in the instrument panel. Exhaust leaks may result in harmful and potentially lethal fumes entering the passenger compartment. -
Page 158
1. Clean the reservoir cap before removal. 2. Check the fluid level. 3. If necessary, add brake fluid from a clean, unopened container. Do not fill above the MAX line. Note: Use only a DOT 3 brake fluid that meets Ford Motor Company specifications. -
Page 159
Maintenance and Specifications Do not let the master cylinder reservoir run dry. This may cause your brakes to fail. Brake fluid is toxic. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Seek medical attention if irritation persists. -
Page 160
Maintenance and Specifications 8. Remove the dipstick and inspect the fluid level. Level should be in the cross-hatched area. 9. If necessary, add fluid in 250ml (1/2 pint) increments through the filler tube until the level is correct at normal operating temperatures. Refer to the Lubricant Specifications section in this chapter for the correct fluid type. -
Page 161
4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. -
Page 162
3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford Motor Company specifications. INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. -
Page 163
Maintenance and Specifications U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. -
Page 164
Maintenance and Specifications SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire gauge. • Check the pressure when the tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). -
Page 165
Maintenance and Specifications • Five tire rotation To make sure your tires wear evenly, rotate them as indicated in the Scheduled Maintenance Guide. If your tires wear unevenly, have them checked. Replacing tires Replace the tires when the wear band is visible. Due to exposure to the elements and exhaust you should replace the spare tire when you replace the other tires. -
Page 166
Your tires have all-weather treads to provide traction in the rain and snow. In some climate, using snow tires or traction devices may be necessary. For Motor Company offers tire cables as a Ford approved accessory and recommends use of these or SAE class “S” cables. See your dealer for more information. -
Page 167: Part Numbers
FL-820S PCV valve EV-243 Spark plugs* AGSF-22PP * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Brake and Motorcraft High clutch fluid Performance DOT 3 Motor Vehicle Brake Fluid…
-
Page 168
Maintenance and Specifications Fluid Ford Part Name Transfer case Motorcraft MERCON ATF Engine coolant Motorcraft Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) Front axle Motorcraft SAE lubricant 80W-90 Premium Rear Axle Lubricant Rear axle Motorcraft SAE… -
Page 169
Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok axles. Service refill capacity for the manual transmission is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. -
Page 170: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Ford Part Item Name or equivalent Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler Multi-Purpose door hinge and Grease spring, hood latch, auxiliary latch, seat tracks High Hydraulic clutch Performance fluid and brake…
-
Page 171
MERCON and MERCON V are not interchangeable. DO NOT mix MERCON and MERCON V. Refer to your scheduled maintenance guide to determine the correct service interval. Conventional rear axles are filled with Motorcraft SAE 80W-90 Premium Rear Axle Lubricant, part number XY-80W90-QL, Ford specification WSP-M2C197-A. Ford Part Ford… -
Page 172
Performance Synthetic Rear Axle Lubricant, part number F1TZ-19780-B, Ford specification WSL-M2C192-A. Add 118 ml (4 oz) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A to Traction-Lok rear axles whenever the axle has been serviced. ENGINE DATA Engine… -
Page 173
Maintenance and Specifications * Height includes roof rack & P255 tire… -
Page 174
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side. -
Page 175: Accessories
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
-
Page 176
Accessories Comfort and convenience Engine block heater Electrochromic compass mirror Electrochromic compass mirror with temperature display Side window deflectors Speed control Tire step Travel equipment Bike carriers Luggage/cargo carrier Raised cross bars Roof rack (removable) Ski/snowboard carrier Seatback organizer (with removable headrest) Soft luggage cover Trailer hitch assembly Trailer hitch balls (all capacities) -
Page 177
(Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. Accessories… -
Page 178: Index
Index Air bag supplemental restraint system …70–71, 74 and child safety seats …72 description …71, 74 disposal …77 driver air bag …73, 75 indicator light …74, 76 operation …73, 75 passenger air bag …73, 75 side air bag …74 Air cleaner filter …167 Anti-lock brake system (see Brakes) …90–91 Audio system (see Radio) …14, 18…
-
Page 179
Customer Assistance …111 Ford accessories for your vehicle …141 Ford Extended Service Plan …130 Getting assistance outside the U.S. and Canada …134 Getting roadside assistance …111 Getting the service you need …128 Ordering additional owner’s literature …135 The Dispute Settlement Board …131… -
Page 180
Index Headlamps aiming …25 autolamp system …24 flash to pass …25 high beam …25 Heating heating and air conditioning system …22 Ignition …86, 172 Infant seats (see Safety seats) …80 Instrument panel cleaning …140 cluster …8 Keyless entry system …51 Keys positions of the ignition …86 Lamps… -
Page 181
Safety belts (see Safety restraints) …60–64 Safety defects, reporting …136 Safety restraints …60–64 belt minder …66 cleaning the safety belts …69 extension assembly …69 for adults …61–64 for children …77 warning light and chime …65 Safety seats for children …80 Seat belts (see Safety restraints) …60 Seats …55…
This manual is also suitable for:
Explorer 2002