Мануал на двигатель 6d16

• 10, * Empty mass as measured according to Mitsubishi Motors Corporation standard. Engine Outputs Classified By Application NOTE 1. The output (SAE, gross) is corrected to standard ambient conditions based on SAE J1349. 2. The continuous rated output allows 10% (one hour) overload operation. 00-2 GENERAL SPECIFICATIONS Item Specifications Engine model 6D16 6D16-TLE Type 6-cylinder in-line, water…

• 12, CAT 6D16 In order to determine the condition of the vehicle adequately, attend the vehicle beforehand to find and keep record of the accumulated mileage, operating condition, what the customer’s demand is, and other information that may be necessary. Prepare the steps to be taken and perform efficient and wasteless maintenance procedure. Determine where the fault exists and che…

• 21, CAT 6D16 • Use specified bolts and nuts and tighten them at specified torques according to the following table, unless otherwise specified. • Threads and contact seats shall be dry. • Where there is a difference in strength classification between the nut and bolt (or stud bolt), the torque specified for the bolt shall apply. Hex-head Bolt and Stud Bolt Unit: N·m (kgf·m) [lbf…

• 17, Using male pins Touch the pins directly using test probes. CAUTION Be sure that you do not short circuit the connector pins when you use the test probe because this could damage the internal circuit of the electronic control unit. Connector Inspection Procedures Visual inspection Check for loose connection and poor engagement. Check if harnesses are broken by pulling gently around the termina…

• 25, Tightening torque for flare nut for general purpose Unit: N·m (kgf·m) [lbf·ft] Tightening torque for air piping nylon tube for general purpose {DIN type} Unit: N·m (kgf·m) [lbf·ft] Tightening torque for air piping nylon tube for general purpose {SAE type} Unit: N·m (kgf·m) [lbf·ft] Pipe diameter φ4.76 mm φ6.35 mm φ8 mm φ10 mm φ12 mm φ15 mm (φ0.187 in.) (φ0.250 in.) (φ0.3…

• 11, CAT 6D16 The serial number for engine is assigned to the respective engine in manufacturing sequence: every engine has its own number. This number is required for incidental inspection of the engine. Please do not fail to mention this number to the dealers when ordering spare parts. Engine Number Engine number 1 is punch-marked on the left of the crankcase. Example: 6D16– Name Plate The name …

• 2, diesel engine Shop Manual (for industrial use) FOREWORD This Shop Manual is published for the information and guidance of personnel responsible for maintenance of 6D16 diesel engine, and includes procedures for adjustment and maintenance services. We earnestly look forward to seeing that this manual is made full use of in order to perform correct service with no wastage. For more details, pl…

• 35, 11-12 ● Assembly sequence Follow the disassembly sequence in reverse. CYLINDER HEAD AND VALVE MECHANISM 04134 ● Disassembly sequence 1 Joint 2 Oil filler cap 3 Bolt 4 Plate 5 Rubber 6 Rocker cover gasket 7 Rocker cover 8 Cylinder head bolt 9 Rocker and bracket assembly P.11-16 10 Cylinder head and valve assembly P.11-20 11 Cylinder head gasket 12 Push rod 13 Tappet * : Crankcase …

• 6, CAT 6D16 2. Service standards table Service standards Unit: mm (in.) 3. Tightening torque table Tightening torques Unit: N·m (kgf·m) [lbf·ft] 4. Lubricants and sealant table Lubricants and sealant Location Maintenance item Standard value Limit Remedy 1, 11 Clearance between strap bolt and strap 0.01 to 0.16 0.3 (0.0118) Replace plate (0.0039 to 0.0629) 7 Pressure spring Installed load …

• 28, 2. Valve Mechanism 1 Exhaust valve 2 Inlet valve 3 Camshaft 4 Tappet 5 Push rod 6 Rocker shaft 7 Rocker shaft spring 8 Rocker 9 Rocker shaft bracket 10 Valve cap 11 Valve cotter 12 Upper retainer 13 Outer valve spring 14 Inner valve spring 15 Valve stem seal 16 Valve guide • The valve stem seals 15 are fitted onto the valves 1, 2 to control the amount of lubricant flowing onto the sliding su…

• 7, 5. Special tools table Special tools Unit: mm (in.) 6. Service procedure Removal and installation of clutch cover • Depress pressure spring 7 using clutch installer, then remove the following parts: Strap bolt 1, washer 2, washer 3, bolt 4, lock plate 5, support nut 6 • Loosen the clutch installer gradually, then remove clutch cover 11 when the pressure spr…

• 37, 11-14 • Loosen and remove the cylinder head bolts 8 in the sequence shown. Each cylinder head bolt should be loosened a little at a time. [Installation] CAUTION Before fitting any cylinder head bolt 8, check the punch marks A on its head. Do not use the bolt if there are more than two punch marks. The punch marks indicate the number of times each bolt has been ti…

• Instruction 51-125511-29-11Copyright®, 2003, 2006, 2008, 2009by S&S Cycle, Inc.All rights reserved.Printed in the U.S.A.Installation Instructions: S&S®Crankcase forHarley-Davidson®Twin Cam 88®EnginesFor all S&S Stock Bore, 4″ Bore, and 41/8″ Bore Twin Cam 88®engine caseswith 1999-2006 and 1984-1999 engine mounts.S&S®®Cycle, Inc.14025 County Highway G PO …

  Crankcase for Harley-Davidson 12

• Operator’s ManualOriginal Operating Instructions Viper® 340cc4-Cycle Engine P/N: 21203ECN: 10638REV1: 12/15/14© 2014 Ardisam, Inc.All Rights ReservedGet parts online at www.ardisam.com GAS/OILRATIO50:1 …

  340cc 4-Cycle Engine 24

• Chapter 1: Getting StartedPage 1–1IronHorse® General Purpose AC Motors User Manual – 10th Ed. Rev A – 01/06/2021Table of ConTenTsManual Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �1– …

  MTF2 Series 25

• How This Manual Is Compiled • This manual is compiled by classifying various systems into certain groups. • Each group contains specifications; troubleshooting; maintenance service standards; tightening torque; lubricant, fluid and sealant; special tools; and service procedure. • Page enumeration is independent by every group where first page is always 1. ii HOW TO READ THIS MANUAL Group No. Group denomination Contents 00 General General specifications, engine No. and na

• Tightening torque for flare nut for general purpose Unit: N·m (kgf·m) [lbf·ft] Tightening torque for air piping nylon tube for general purpose {DIN type} Unit: N·m (kgf·m) [lbf·ft] Tightening torque for air piping nylon tube for general purpose {SAE type} Unit: N·m (kgf·m) [lbf·ft] Pipe diameter φ4.76 mm φ6.35 mm φ8 mm φ10 mm φ12 mm φ15 mm (φ0.187 in.) (φ0.250 in.) (φ0.315 in.) (φ0.394 in.) (φ0.472 in.) (φ0.591 in.) Tightening torque 17 25 39 59 88 98 (1.7) (2.6) (4.0) (6.0) (9.0) (10.0) [12.5] [18.4] [28.8] [43.5] [64.9]

• 1. Illustration for disassembly and assembly or removal and installation iv HOW TO READ THIS MANUAL This shows that the appropriate service procedure is described in the text. This shows the key No. of the part. In the text, this No. is referred to uniformly throughout. This shows an example of the disassembly (removal) sequence. No service procedure is referred to in this section, but the item can be an objective of various procedures. This is shown when the assembly (installation) sequence is not the reverse of the disassembly (removal) sequence. M

• 4. Pistons A: Part number B: “T” mark <6D16-TLE> C: Size mark (A, B: <6D16, 6D16-TLE>) D: Weight mark : Front mark 5. Timing Gears 1 Camshaft gear 2 No. 2 idler gear 3 No. 1 idler gear 4 Oil pump gear 5 Crankshaft gear 6 Air compressor drive gear or injection pump drive gear 7 No. 1 idler gear Each gear is stamped with a timing gear alignment mark (“1”, “2”, “3”, or “4”) to facilitate reassembly. 6. Flywheel 1 Flywhee

• 11-18 Rocker shaft Align the oil hole G in the No. 6 rocker shaft bracket 6 with the oil hole H in the rocker shaft 14. CYLINDER HEAD AND VALVE MECHANISM 13024
  

• General Explanation of This Manual ● Specifications Particulars relative to maintenance service are made. ● Structure and operation (1) Regarding conventional equipment, descriptions are made in brief. (2) Regarding new equipment, descriptions of system and operating condition are made in detail. ● Troubleshooting Symptoms of troubles and possible causes are described comparatively. ● Inspection and adjustment mounted in vehicle Descriptions are made regarding inspection and adjustment of units mounted in vehicle. ●

• When using testers or the like for continuity tests, be careful not to allow test probes to touch the wrong terminals. Measurement Procedures Using Connectors Test with connectors engaged (continuity through circuit obtained) <Waterproof connector> Prepare a test harness and connectors A, then connect if between the two parts of harness B that is to be tested. Check the circuit by touching test probe C to the te

• 11-10 2. Inspecting and Adjusting Valve Clearances Service standards Unit: mm (in.) Tightening torques Unit: N·m (kgf·m) [lbf·ft] Valve clearances should be checked and adjusted when the engine is cold. [Inspection] • Bring piston No. 1 or piston No. 6 to the top-dead-centre (TDC) position of its compression stroke. To do this, crank the engine until the “1.6” mark inscribed on th

• 11-6 TROUBLESHOOTING Incorrect oil viscosity Gr 11 Incorrect/defective fuel Gr 13 Incorrect valve clearance Defective cylinder head gasket Worn valve/valve seat, and carbon deposits Weakened valve spring Worn/damaged piston ring(s) Worn/damaged piston ring groove(s) Incorrect injection timing Gr 13 Defective injection pump Gr 13 Defective cooling system Gr 14 Defective injection nozzle(s) Gr 13 Air trapped in fuel system Gr 13 Clogged air cleaner Gr 15 Clogged muffler Gr 15 Defective turbocharger Gr 15 I

• Terms and Units The terms and units in this manual are defined as follows. ● This service manual contains important cautionary instructions and supplementary information under the following four headings which identify the nature of the instructions and information: DANGER WARNING CAUTION NOTE ● Front and rear The terms “front” is the fan side and “rear” the flywheels side of the engine. ● Left and right The

• Be particularly careful not to work in shoes that have oily soles and are slippery. When working as a team of two or more, arrange signals in advance and keep confirming safety. Be careful not to accidentally bump switches or levers. Check for oil leakage before cleaning the area having the fault otherwise you might miss detecting the leakage. Prepare replacement part(s) beforehand. Replace oil seals, packing, O-rings and other rubber parts; gaskets and split

• Service Manual 99709-68130 For use with Chassis Service Manual. 6D16 Diesel Engine DP80 T32B-00011-up DP90 T32B-50001-up DP100 3DP-00001-up DP115 4DP-00001-up DP135 5DP-00001-up DP150 6DP-00011-up
  

• 11-17 11 ◆ Service procedure Rocker bushing and rocker shaft [Inspection] If any clearance exceeds the specified limit, replace the defective part(s). Rocker bushing [Removal] [Installation] • Align the oil hole A in the rocker bushing 2 with the oil hole B in the rocker 5. • Position the notch C and seam D on the rocker bushing 2 as shown. • Install the rocker bushing 2 into the rocker 5 from the chamfered side F. to Installing rocker shaft brackets and rocker shaft Rocker shaft brackets Be sure to fit the rocker shaft brackets 6, 8, 12 in their correct p

• • Use specified bolts and nuts and tighten them at specified torques according to the following table, unless otherwise specified. • Threads and contact seats shall be dry. • Where there is a difference in strength classification between the nut and bolt (or stud bolt), the torque specified for the bolt shall apply. Hex-head Bolt and Stud Bolt Unit: N·m (kgf·m) [lbf·ft] 00-12 TABLE OF STANDARD TIGHTENING TORQU

• 1. Cylinder Head and Crankcase 1 Connecting plate 2 Glow plug 3 Cylinder liner 4 Crankcase 5 Water jacket 6 Piston 7 Injection nozzle 8 Cylinder head A: Cylinder liner size mark Outer diameter mark: 1, 2, 3 Inner diameter mark: A, B • The cylinder liners 3 are a dry type liners that are easier to remove than wet liners. Liners are press-fitted into the crankcase 4. • The cylinder liners 3, crankcase 4, and pistons 6 have size marks. They should be combined as specified accordin

1. Двигатели Mitsubishi 6D14, 6D14-T, 6D15-T, 6D16, 6D17 / Hyundai D6BR: Устройство, техническое обслуживание и ремонт

   

   Издательство: Легион-Автодата
   Жанр: Устройство и системы автомобиля

   Качество: Хорошее
   Страниц: 248
   Формат: pdf, fb2, epub

   В руководстве дается подробное пошаговое описание процедур по ремонту и техническому обслуживанию дизельных двигателей Mitsubishi серии 6D14 (6557 см3), 6D14-T (6557 см3), 6D15-T (6919 см3), 6D16 (7545 см3), 6D17 (8201 см3), и двигателей Hyundai серии D6BR (7545 см3). Издание содержит подробные сведения по ремонту и регулировке механизмов двигателя, системы смазки, охлаждения, топливной системы, системы турбонаддува и системы электрооборудования двигателя. Подробно рассмотрены настройки и регулировки различных ТНВД и регуляторов (RSV, RFD, R901, R801, RLD-J, включая регулятор RED-III с электронным управлением), форсунок, системы поддержания скорости, системы горного тормоза, моторного тормоза (Powertardo и Jake Brake), инерционного наддува. Приведены инструкции по использованию системы самодиагностики ТНВД с электронным управлением (RED-III), системы поддержания скорости, электросхемы систем с электронным управлением. Руководство содержит возможные неисправности и методы их устранения, сопрягаемые размеры основных деталей и пределы их допустимого износа, рекомендуемые смазочные материалы и рабочие жидкости. Книга предназначена для автовладельцев, персонала СТО и ремонтных мастерских.

   Вложения:

Только оригинальные руководства

Доступно сразу после оплаты

Полное соответствие бумажным изданиям

100% защита ваших оплат

О руководстве

Тип двигателя: Caterpillar 6D16

В руководстве вы найдете

• Пошаговое руководство по ремонту различных узлов и агрегатов
• Инструкцию по самостоятельному уходу и обслуживанию
• Сведения о конструкции двигателя и о том как предупредить неисправность
• Информацию для поездки на СТО, если самостоятельный ремонт невозможен

Написать отзыв

Ваше Имя:

Ваш отзыв:

Оценка:

Tolle Motorreparaturanleitung! Ich konnte alles selbst und ohne Probleme machen.