Msi z97 gaming 5 инструкция на русском

• Page 1
  Preface Z97 GAMING 5 Motherboard G52-79171X1…

• Page 2: Preface

  Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.

• Page 3: Smartphone Application

  If a problem arises with your system and no solution can be obtained from the user’s manual, please contact your place of purchase or local distributor. Alternatively, please try the following help resources for further guidance. Visit the MSI website for technical guide, BIOS updates, driver updates, and other information: http://www.msi.com/service/download/ Contact our technical staff at: http://register.msi.com/…

• Page 4: Safety Instructions

  Safety Instructions ￭ Always read the safety instructions carefully. ￭ Keep this User’s Manual for future reference. ￭ Keep this equipment away from humidity. ￭ Lay this equipment on a reliable flat surface before setting it up. ￭ The openings on the enclosure are for air convection hence protects the equipment from overheating.

• Page 5: Fcc-B Radio Frequency Interference Statement

  FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

• Page 6: Radiation Exposure Statement

  Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment and its antenna should be installed and operated with minimum distance 20 cm between the radiator and your body. This equipment and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

• Page 7: Battery Information

  Replace only with the same or equivalent type recommended by the manufacturer. Chemical Substances Information In compliance with chemical substances regulations, such as the EU REACH Regulation (Regulation EC No. 1907/2006 of the European Parliament and the Council), MSI provides the information of chemical substances in products at: http://www.msi.com/html/popup/csr/evmtprtt_pcm.html Preface…

• Page 8: Weee (Waste Electrical And Electronic Equipment) Statement

  MSI will comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these products to local collection points.

• Page 9
  MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na lokalnim mestima za prikupljanje.
• Page 10
  MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita.

• Page 11: Table Of Contents

  CONTENTS ▍ Preface ………………….i Copyright Notice ………………….ii Trademarks ………………….ii Revision History ………………….ii Smartphone Application ………………iii Technical Support ………………..iii Safety Instructions ………………..iv FCC-B Radio Frequency Interference Statement ……….. v CE Conformity ………………….v Radiation Exposure Statement …………….vi European Community Compliance Statement …………vi Taiwan Wireless Statements ……………….vi Japan VCCI Class B Statement …………….vi Korea Warning Statements ………………vi…

• Page 12
  Internal Connectors ……………….. 1-20 SATA1~6: SATA Connectors …………..1-20 CPUFAN1~2,SYSFAN1~3: Fan Power Connectors ……..1-21 JFP1, JFP2: System Panel Connectors …………1-22 JUSB1~2: USB 2.0 Expansion Connectors ……….1-23 JUSB3: USB 3.0 Expansion Connector …………1-23 JCI1: Chassis Intrusion Connector ………….. 1-24 JAUD1: Front Panel Audio Connector …………
• Page 13
  Operation ………………….3-6 Updating BIOS ………………… 3-7 Updating the BIOS with M-FLASH …………..3-7 SETTINGS ………………….3-8 System Status ………………..3-8 Advanced ………………….. 3-9 Boot ………………….3-15 Security ………………….3-16 Save & Exit ………………..3-17 OC ……………………3-18 M-FLASH ………………….3-25 OC PROFILE …………………

• Page 15: Chapter 1 Getting Started

  Chapter 1 Getting Started Thank you for choosing the Z97 GAMING 5 Series (MS-7917 v1.X) ATX motherboard. The Z97 GAMING 5 Series motherboards are based on Intel ® Z97 chipset for optimal system efficiency. Designed to fit the advanced Intel ®…

• Page 16: Packing Contents

  * These pictures are for reference only and may vary without notice. * The packing contents may vary according to the model you purchased. * If you need to purchase the optional accessories or request part numbers, please visit the MSI website at http://www.msi.com/index.php or consult the dealer. Getting Started…

• Page 17: Assembly Precautions

  Assembly Precautions ■ The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly. ■ Always turn off the power supply and unplug the power cord from the power outlet before installing or removing any computer component.

• Page 18: Motherboard Specifications

  Motherboard Specifications ■ Supports 4th and 5th Generation Intel Core™ Processors, and ® Intel Pentium and Celeron Processors for Socket LGA1150 Support ® ® ® Chipset ■ Intel Z97 Express Chipset ® Memory ■ 4x DDR3 memory slots supporting up to 32GB ■…

• Page 19
  Back Panel ■ 1x PS/2 keyboard/ mouse combo port ■ 4x USB 2.0 ports Connectors ■ 1x VGA connector ■ 1x DVI-D connector ■ 1x LAN (RJ45) port ■ 4x USB 3.0 ports ■ 1x HDMI ports ■ 6x OFC audio jacks Internal ■…
• Page 20
  Killer Network Manager Form ■ ATX Form Factor ■ 12 in. x 9.6 in. (30.5 cm x 24.4 cm) Factor For the latest information about CPU, please visit http://www.msi.com/cpu-support/ For more information on compatible components, please visit http://www.msi.com/test-report/ Getting Started…

• Page 21: Connectors Quick Guide

  Connectors Quick Guide DIMM3 DIMM2 DIMM4 SYSFAN1 DIMM1 CPUFAN1 JPWR2 CPU Socket CPUFAN2 M2_1 Back Panel JPWR1 SYSFAN3 PCI_E1 PCI_E2 JUSB3 PCI_E3 SATA1_2 PCI_E4 SATA3_4 PCI_E5 SATA5_6 JCI1 PCI_E6 JBAT1 AUD_SW1 PCI_E7 SYSFAN2 JTPM1 JUSB2 JFP2 JCOM1 JUSB1 AUDPWR1 JFP1 JAUD1 Getting Started…

• Page 22
  Connectors Reference Guide Port Name Port Type Page Back Panel I/O Ports AUD_SW1 Audio Power Switch 1-28 AUDPWR1 Direct Audio Power Connector 1-25 LGA1150 CPU Socket 1-12 CPUFAN1~2,SYSFAN1~3 Fan Power Connectors 1-21 DIMM1~4 DDR3 Memory slots 1-15 JAUD1 Front Panel Audio Connector 1-24 JBAT1 Clear CMOS Jumper…

• Page 23: Back Panel Quick Guide

  Back Panel Quick Guide PS/2 Keyboard/ Mouse Combo Port* LAN Port USB 3.0 Port Line-In RS-Out USB 2.0 Port Line-Out CS-Out SS-Out USB 2.0 Port* DVI-D USB 3.0 Port HDMI * Gaming Device Port. ▶ PS/2 Keyboard/Mouse Combo Port A combination of PS/2 mouse/keyboard DIN connector for a PS/2 mouse/keyboard.

• Page 24
  ▶ USB 2.0 Port The USB 2.0 port is for attaching USB 2.0 devices such as keyboard, mouse, or other USB 2.0-compatible devices. ▶ USB 3.0 Port USB 3.0 port is backward-compatible with USB 2.0 devices. It supports data transfer rate up to 5 Gbit/s (SuperSpeed).

• Page 25: Cpu (Central Processing Unit)

  This motherboard is designed to support overclocking. Before attempting to overclock, please make sure that all other system components can tolerate overclocking. Any attempt to operate beyond product specifications is not recommend. MSI does not guarantee the damages or risks caused by inadequate operation beyond product specifications.

• Page 26: Cpu & Heatsink Installation

  CPU & Heatsink Installation When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink is necessary to prevent overheating and maintain system stability. Follow the steps below to ensure correct CPU and heatsink installation. Wrong installation can damage both the CPU and the motherboard.

• Page 27
  3. Align the notches with the socket alignment keys. Lower the CPU straight down, without tilting or sliding the CPU in the socket. Inspect the CPU to check if it is properly seated in the socket. 4. Close and slide the load plate under the retention knob. Close and engage the load lever.
• Page 28
  7. Locate the CPU fan connector on the motherboard. 8. Place the heatsink on the motherboard with the fan’s cable facing towards the fan connector and the fasteners matching the holes on the motherboard. CPU fan connector 9. Push down the heatsink until the four fasteners get wedged into the holes on the motherboard.

• Page 29: Memory

  Memory These DIMM slots are used for installing memory modules. DIMM1 DIMM2 DIMM3 DIMM4 Video Demonstration Watch the video to learn how to install memories at the address below. http://youtu.be/76yLtJaKlCQ Dual-Channel mode Population Rule In Dual-Channel mode, the memory modules can transmit and receive data with two data bus channels simultaneously.

• Page 30: Mounting Screw Holes

  Mounting Screw Holes When installing the motherboard, first install the necessary mounting stands required for an motherboard on the mounting plate in your computer case. If there is an I/O back plate that came with the computer case, please replace it with the I/O backplate that came with the motherboard package.

• Page 31: Power Supply

  Power Supply Video Demonstration Watch the video to learn how to install power supply connectors. http://youtu.be/gkDYyR_83I4 JPWR1~2: ATX Power Connectors These connectors allow you to connect an ATX power supply. To connect the ATX power supply, align the power supply cable with the connector and firmly press the cable into the connector.

• Page 32: Expansion Slots

  Expansion Slots This motherboard contains numerous slots for expansion cards, such as discrete graphics or audio cards. PCI_E1~7: PCIe Expansion Slots The PCIe slot supports the PCIe interface expansion card. PCIe 3.0 x16 Slot PCIe 2.0 x1 Slot Important When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet.

• Page 33: Video/ Graphics Cards

  Adding on one or more discrete video cards will significantly boost the system’s graphics performance. For best compatibility, MSI graphics cards are recommended. Video Demonstration Watch the video to learn how to install a graphics card on PCIe x16 slot with butterfly lock.

• Page 34: Internal Connectors

  Internal Connectors SATA1~6: SATA Connectors This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray). Video Demonstration Watch the video to learn how to Install SATA HDD. http://youtu.be/RZsMpqxythc SATA2 SATA1…

• Page 35: Cpufan1~2,Sysfan1~3: Fan Power Connectors

  CPUFAN1~2,SYSFAN1~3: Fan Power Connectors The fan power connectors support system cooling fans with +12V. If the motherboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the CPU fan control. Remember to connect all system fans.

• Page 36: Jfp1, Jfp2: System Panel Connectors

  JFP1, JFP2: System Panel Connectors These connectors connect to the front panel switches and LEDs. The JFP1 connector is compliant with the Intel Front Panel I/O Connectivity Design Guide. When ® installing the front panel connectors, please use the optional M-Connector to simplify installation.

• Page 37: Jusb1~2: Usb 2.0 Expansion Connectors

  JUSB1~2: USB 2.0 Expansion Connectors This connector is designed for connecting high-speed USB peripherals such as USB HDDs, digital cameras, MP3 players, printers, modems, and many others. Important Note that the VCC and GND pins must be connected correctly to avoid possible damage.

• Page 38: Jci1: Chassis Intrusion Connector

  JCI1: Chassis Intrusion Connector This connector connects to the chassis intrusion switch cable. If the computer case is opened, the chassis intrusion mechanism will be activated. The system will record this intrusion and a warning message will flash on screen. To clear the warning, you must enter the BIOS utility and clear the record.

• Page 39: Audpwr1: Direct Audio Power Connector

  AUDPWR1: Direct Audio Power Connector This connector is used to provide direct power to back panel audio ports. The direct audio power can provide the better audio quality. Please connect this connector with a power supply by an audio power adapter. Important After connecting the direct power to this connector, please note that you have to enable the “Direct Audio Power”…

• Page 40: Jtpm1: Tpm Module Connector

  JTPM1: TPM Module Connector This connector connects to a TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages. JCOM1: Serial Port Connector This connector is a 16550A high speed communication port that sends/receives 16 bytes FIFOs.

• Page 41: Jumper

  Jumper JBAT1: Clear CMOS Jumper There is CMOS RAM onboard that is external powered from a battery located on the motherboard to save system configuration data. With the CMOS RAM, the system can automatically boot into the operating system (OS) every time it is turned on. If you want to clear the system configuration, set the jumpers to clear the CMOS RAM.

• Page 42: Switch

  Switch AUD_SW1: Audio Power Switch This switch specifies the power mode for back panel audio ports. Onboard Power mode (Default) Direct Power mode Important • Before switching to «Direct Power mode», please make sure the «Direct Audio Power Connector” (AUDPWR1) has been connected to the power supply. Do not use the audio power switch while the system is on because it will damage •…

• Page 43: Led Status Indicators

  LED Status Indicators MSI LED Debug LED LED Status Table The following table describes the status of LED indicators. LED Status Description MSI LED Debug 1-29 Getting Started…

• Page 44: Debug Code Led Table

  Debug Code LED Table Please refer to the table below to get more information about the Debug Code LED message. Post Status 02,07 Power on CPU Initialization 03,08 Power on North Bridge Initialization 04,09 Power on South Bridge Initialization Power on Cache Initialization 11~14,32~36,56~5A Early CPU Initialization 15~18,37~3A…

• Page 45: Drivers And Utilities

  After you install the operating system you will need to install drivers to maximize the performance of the new computer you just built. MSI motherboard comes with a Driver Disc. Drivers allow the computer to utilize your motherboard more efficiently and take advantage of any special features we provide.

• Page 47
  Chapter 2 Quick Installation This chapter provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet. You may have even link to the URL by scanning the QR code. Important The diagrams in this chapter are for reference only and may vary from the product you purchased.
• Page 48
  CPU Installation http://youtu.be/bf5La099urI Quick Installation…

• Page 49: Chapter 2 Quick Installation

  Quick Installation…

• Page 50: Memory Installation

  Memory Installation http://youtu.be/76yLtJaKlCQ Quick Installation…

• Page 51: Motherboard Installation

  Motherboard Installation Quick Installation…

• Page 52
  Quick Installation…

• Page 53: Power Connectors Installation

  Power Connectors Installation http://youtu.be/gkDYyR_83I4 Quick Installation…

• Page 54
  Quick Installation…

• Page 55: Sata Hdd Installation

  SATA HDD Installation http://youtu.be/RZsMpqxythc Quick Installation…

• Page 56: M.2 Module Installation

  M.2 module Installation 4.2 cm 6 cm 8 cm Quick Installation 2-10…

• Page 57: Front Panel Connector Installation

  Front Panel Connector Installation JFP1 Connector Installation http://youtu.be/DPELIdVNZUI Front Panel Audio Connector Installation 2-11 Quick Installation…

• Page 58: Peripheral Connector Installation

  Peripheral Connector Installation USB2.0 Connector Installation USB3.0 Connector Installation Quick Installation 2-12…

• Page 59: Graphics Card Installation

  Graphics Card Installation http://youtu.be/mG0GZpr9w_A 2-13 Quick Installation…

• Page 60
  Quick Installation 2-14…

• Page 61: Chapter 3 Bios Setup

  Chapter 3 BIOS Setup CLICK BIOS is a revolutionary UEFI interface that allows you to setup and configure your system for optimum use. Using your mouse and keyboard, users can change BIOS settings, monitor CPU temperature, select the boot device priority and view system information such as the CPU name, DRAM capacity, the OS version and the BIOS version.

• Page 62: Entering Setup

  (optional) on the motherboard to enable the system going to BIOS setup directly at next boot. Click «GO2BIOS» tab on «MSI Fast Boot» utility screen. Important Please be sure to install the “MSI Fast Boot” utility before using it to enter the BIOS setup. BIOS Setup BIOS Setup…

• Page 63: Overview

  Overview After entering BIOS, the following screen is displayed. Temperature monitor My Favorites Language System information Boot device priority bar Virtual OC Genie Button BIOS menu BIOS menu selection selection Menu display ▶ BIOS menu selection The following options are available: ■…

• Page 64
  Enables or disables the OC Genie function by clicking on this button. When enabled, this button will be light. Enabling OC Genie function can automatically overclock with MSI optimized overclocking profile. Important We recommend that you do not to make any modification in OC menu mode and do not to load defaults after enabling the OC Genie function.
• Page 65
  Adding BIOS item to Favorite 1~5 Move the mouse cursor to highlight a BIOS setting item. Right-click (or press «F2» key) and then choose a favorite menu (Favorite 1~5) to add the BIOS item. Choose a favorite menu to add the BIOS item Deleting BIOS item from Favorite 1~5 Move the mouse cursor to highlight a BIOS item on the Favorite 1~5 menu.

• Page 66: Operation

  Operation You can control BIOS settings with the mouse and the keyboard. The following table lists and describes the hot keys and the mouse operations. Hot key Mouse Description <↑↓→← > Select Item Move the cursor <Enter> Select Icon/ Field Click/ Double-click the left button <Esc>…

• Page 67: Updating Bios

  Updating the BIOS with M-FLASH ▶ Before updating Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash disk. Important Only the FAT32/ NTFS format USB flash disk supports updating BIOS by M-FLASH.

• Page 68: Settings

  SETTINGS System Status ▶ System Date Sets the system date. Use tab key to switch between date elements. The format is <day> <month> <date> <year>. <day> Day of the week, from Sun to Sat, determined by BIOS. Read-only. <month> The month from Jan. through Dec. <date>…

• Page 69: Advanced

  Advanced ▶ PCI Subsystem Settings Sets PCI, PCI express interface protocol and latency timer. Press <Enter> to enter the sub-menu. ▶ CPU PCI-E Lane Configuration [Auto] It can help you conveniently and directly manage the configuration of the PCI-E lanes from CPU. ▶…

• Page 70: Intel Rapid Start Technology

  ▶ Ipv6 PXE Support [Enabled] When “Enabled”, the system UEFI network stack will support Ipv6 protocol. This item will appear when “Network Stack” is enabled. [Enabled] Enables the Ipv6 PXE boot support. [Disabled] Disables the Ipv6 PXE boot support. ▶ SATA Mode [AHCI Mode] Sets the operation mode of the onboard SATA controller.

• Page 71
  ▶ Intel(R) Rapid Start Technology [Disabled] Intel Rapid Start Technology lets the system resume from sleep mode quickly. ® This function is available when an SSD is installed. [Enabled] Enables Intel Rapid Start Technology. [Disabled] Disables Intel Rapid Start Technology. ▶…

• Page 72: Usb Configuration

  ▶ LakeTiny Feature [Disabled] Enables or disables Intel Lake Tiny feature with iRST for SSD. This item appears when a installed CPU supports this function and «Intel C-State» is enabled. [Enabled] Enhance the dynamic IO load adjusted performance for accelerating the SSD speed.

• Page 73
  Disables this function. ▶ MSI Fast Boot [Disabled] MSI Fast Boot is the fastest way to boot the system. It will disable more devices to speed up system boot time which is faster than the boot time of “Fast Boot”. [Enabled] Enables the MSI Fast Boot function to speed up booting time.
• Page 74
  Disables the Fast Boot configuration. Important If you want to enter BIOS with enabled “MSI Fast Boot” mode or enabled «Fast Boot» mode, you have to click the «GO2BIOS» tab on MSI Fast Boot utility screen or press the «GO2BIOS» button (optional) on the motherboard. And then the system will enter to BIOS setup directly at next boot.

• Page 75: Boot

  ▶ Resume By RTC Alarm [Disabled] Disables or enables the system wake up by RTC Alarm. [Enabled] Enables the system to boot up on a scheduled time/ date. [Disabled] Disables this function. ▶ Date (of month) Alarm/ Time (hh:mm:ss) Alarm Sets RTC alarm date/ Time.

• Page 76: Security

  ▶ Boot Mode Select [LEGACY+UEFI] Sets the system boot mode from legacy or UEFI architecture depending on OS installation requirement. This item will become unselectable and will be configured automatically by BIOS when “Windows 8/ 8.1 Feature” is enabled. [UEFI] Enables UEFI BIOS boot mode support only.

• Page 77: Save & Exit

  ▶ Trusted Computing Sets TPM (Trusted Platform Module) function. ▶ TPM SUPPORT [Disabled] Enables or disables the TPM function to build the endorsement key for accessing the system. ▶ Chassis Intrusion Configuration Press <Enter> to enter the sub-menu. ▶ Chassis Intrusion [Disabled] This function will be available if the chassis equips a chassis intrusion switch.

• Page 78
  Enables the OC Genie function by virtual button in BIOS or physical button on motherboard. Enabling OC Genie function can automatically overclock the system with MSI optimized overclocking profile. [By BIOS Options] OC Genie function is enabled by clicking the virtual OC Genie button at the top left corner of BIOS setup screen.
• Page 79
  ▶ Adjust Ring Ratio [Auto] Sets the ring ratio. The valid value range depends on the installed CPU. ▶ Adjusted Ring Frequency Shows the adjusted Ring frequency. Read-only. ▶ Adjust GT Ratio [Auto] Sets the integrated graphics ratio. The valid value range depends on the installed CPU.
• Page 80
  ▶ VR 12VIN OCP Expander [Auto] Expands the limitation of VR Over Current Protection with 12V input voltage. The higher expanding value indicates less protection. Therefore, please adjust the current carefully if needed, or it may damage the CPU/ VR MOS. If set to «Auto», BIOS will configure this setting automatically.
• Page 81
  ▶ CPU VRM Over Temperature Shutdown [Enabled] Sets the system whether be powered off or not when the CPU VRM temperature over the limitation temperature of CPU VRM protection. [Enabled] The system will be off when over the specified temperature. [Disabled] Disables this function.
• Page 82
  ▶ MEMORY-Z Press <Enter> to enter the sub-menu. This sub-menu displays all the settings and timings of installed memory. You can also access this information menu at any time by pressing [F5]. ▶ DIMMXX Memory SPD Press <Enter> to enter the sub-menu. The sub-menu displays the information of installed memory.
• Page 83
  ▶ Adjacent Cache Line Prefetch [Enabled] Enables or disables the CPU hardware prefetcher (MLC Spatial prefetcher). [Enabled] Enables adjacent cache line prefetching for reducing the cache latency time and tuning the performance to the specific application. [Disabled] Enables the requested cache line only. ▶…
• Page 84
  ▶ EIST [Enabled] Enables or disables the Enhanced Intel SpeedStep Technology. This item will ® appear when «Simple/ Advanced Mode» is set to [Simple]. [Enabled] Enables the EIST to adjust CPU voltage and core frequency dynamically. It can decrease average power consumption and average heat production.

• Page 85: M-Flash

  Enables the system to boot from the BIOS within USB flash disk. [Disabled] Enables the system to boot from the BIOS within ROM on motherboard. *This may cause system unstable, MSI recommend it only for power users. ▶ Select one file to boot Selects a BIOS file in the USB flash disk (NTFS/ FAT 32 format) to boot the system.

• Page 86: Oc Profile

  OC PROFILE ▶ Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6 Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6 management. Press <Enter> to enter the sub- menu. ▶ Set Name for Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6 Names the current overclocking profile. ▶…

• Page 87: Hardware Monitor

  HARDWARE MONITOR Current Temperature & Speed information control field Setting Buttons Voltage display ▶ Current Temperature & Speed information Shows the current CPU temperature, system temperature and fans’ speeds. ▶ Fan control field This motherboard provides a fan speed control feature call “Smart Fan Mode”. Please check the “Smart Fan Mode”…

• Page 89: Appendix A Realtek Audio

  Appendix A Realtek Audio The Realtek audio provides 10-channel DAC that simultaneously supports 7.1 sound playback and 2 channels of independent stereo sound output (multiple streaming) through the Front-Out-Left and Front-Out-Right channels.

• Page 90: Software Configuration

  Software Configuration After installing the audio driver (see Chapter 1 — Driver and Utilities), the “Realtek HD Audio Manager” icon will appear at the notification area (lower right of the screen). You may double click the icon and the GUI will pop up accordingly. double click the icon It is also available to enable the audio driver by clicking the Realtek HD Audio Manager from the Control Panel.

• Page 91: Auto Popup Dialog

  ▶ Device Selection Here you can select a audio output source to change the related options. The “check” sign (in orange) indicates the devices as default. ▶ Volume Adjustment You can control the volume or balance the right/left side of the speakers that you plugged in front or rear panel by adjust the bar.

• Page 92: Hardware Default Setting

  Hardware Default Setting The following diagrams are audio back panel default setting. ■ Backpanel audio jacks to 2-channel speakers diagram F r o ■ Backpanel audio jacks to 4-channel speakers diagram F r o R e a Realtek Audio…

• Page 93
  ■ Backpanel audio jacks to 6-channel speakers diagram F r o C e n R e a t e r & S u b w o o f ■ Backpanel audio jacks to 8-channel speakers diagram F r o C e n R e a t e r &…

• Page 95: Appendix B Intel Raid

  Appendix B Intel RAID This appendix will assist users in configuring and enabling RAID functionality and accelerating system on platforms…

• Page 96: Introduction

  Introduction The motherboard comes with the Intel RAID controller that allows you to configure SATA hard drives as RAID sets. SATA hard drives deliver blistering transfer speeds up to 6 Gb/s. Serial ATA uses long, thin cables, making it easier to connect your drive and improving the airflow inside your PC.

• Page 97: Using Intel Rapid Storage Technology Option Rom

  Using Intel Rapid Storage Technology Option ROM The Intel Rapid Storage Technology Option ROM should be integrated with the system BIOS on all motherboards with a supported Intel chipset. The Intel Rapid Storage Technology Option ROM is the Intel RAID implementation and provides BIOS and DOS disk services.

• Page 98: Create Raid Volume

  After pressing the <Ctrl> and <I> keys simultaneously, the following window will appear: MAIN MENU MAIN MENU Recovery Volume Options Create RAID Volume Acceleration Options Delete RAID Volume Exit Reset Disks to Non-RAID DISK / VOLUME INFORMATION RAID Volumes : None defined.

• Page 99
  In the Disk field, press <Enter> key and use <Space> key to select the disks you want to create for the RAID volume, then click <Enter> key to finish selection. This field will become available according to the selected RAID level. Then select the strip size for the RAID array by using the “upper arrow”…

• Page 100: Intel Raid

  Go to the Create Volume field and press <Enter>, the following screen appears for you to confirm if you are sure to create the RAID volume. Press <Y> to continue. CREATE VOLUME MENU Name : Volume0 RAID Level : RAID1(Mirror) Disks : Select Disks Strip Size :…

• Page 101
  ■ Delete RAID Volume Here you can delete the RAID volume, but please be noted that all data on RAID drives will be lost. Important If your system currently boots to RAID and you delete the RAID volume in the Intel RAID Option ROM, your system will become un-bootable.
• Page 102
  ■ Reset Disks to Non-RAID Select option 3 Reset Disks to Non-RAID and press <Enter> to delete the RAID volume and remove any RAID structures from the drives. The following screen appears: MAIN MENU Recovery Volume Options Create RAID Volume RESET RAID DATA Recovery Volume Options Delete RAID Volume…

• Page 103: Recovery Volume Options

  ■ Recovery Volume Options Select option 4 Recovery Volume Options and press <Enter> to change recovery volume mode. The following screen appears: RECOVERY VOLUME OPTIONS Enable Only Recovery Disk Enable Only Master Disk HELP Enable Only Recovery Disk — enables recovery disk if available and disables master disk.

• Page 104: Degraded Raid Array

  Degraded RAID Array A RAID 1, RAID 5 or RAID 10 volume is reported as degraded when one of its hard drive members fails or is temporarily disconnected, and data mirroring is lost. As a result, the system can only utilize the remaining functional hard drive member. To re-establish data mirroring and restore data redundancy, refer to the procedure below that corresponds to the current situation.

• Page 105
  Exit Intel RAID Option ROM, and then reboot to Windows system. When prompted to rebuild the RAID volume, click ‘Yes’. The Intel Rapid Storage Technology application will be launched. Right-click the new hard drive and select ‘Rebuild to this Disk’. The ‘Rebuild Wizard’ will be launched which will guide you through the process of rebuilding to the new hard drive.

• Page 106: System Acceleration (Optional

  RAID mode, skip to the step 5. Reboot and enter the BIOS steup. Set the SATA Mode to RAID in BIOS. Install Windows operating system. Insert the MSI Driver DVD into the DVD-ROM drive. Install Intel RAID driver Powered off. Connect the SSD.

• Page 107
  Run Intel Rapid Storage Technology application. Click «Enable acceleration» under Accelerate tab. Click here Select the acceleration options. Click OK and reboot the system. The page refreshes and reports the new acceleration configuration in the Acceleration View. Important You can click “More help on this page” or «More help» of the Intel Rapid Storage ®…

• Page 108: Rst Synchronization (Optional

  RST Synchronization (optional) If you are using Maximized mode as the Acceleration mode, the data on the hard disk is not always synchronized with the data in the SSD cache. In some situations, you may want to manually sync the disks for avoiding data loss. Follow these steps to sync manually.

MSI Z97 GAMING 5 motherboard Benutzerhandbuch

Бренд:

MSI

Категория:

Motherboards

Размер:

10 MB

Страниц:

186

Язык(и):

Немецкий, Английский, Французский, Русский

Оглавление

Открыть в новой вкладке