Mvh 150ubg pioneer инструкция на русском

Инструкция и руководство для
Pioneer MVH-150UBG на русском на английском

22 страницы подробных инструкций и пользовательских руководств по эксплуатации

Black plate (2,1)

Thank you for purchasing this PIONEER
product
To ensure proper use, please read through this
manual before using this product. It is especially
important that you read and observe WARN-
INGs and CAUTIONs in this manual. Please
keep the manual in a safe and accessible place for
future reference.

If you want to dispose this product, do not
mix it with general household waste. There is
a separate collection system for used elec-
tronic products in accordance with legislation
that requires proper treatment, recovery and
recycling.

Private households in the member states of the
EU, in Switzerland and Norway may return their
used electronic products free of charge to desig-
nated collection facilities or to a retailer (if you
purchase a similar new one).
For countries not mentioned above, please con-
tact your local authorities for the correct method
of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment, re-
covery and recycling and thus prevent potential
negative effects on the environment and human
health.

About this unit

The tuner frequencies on this unit are allocated
for use in Western Europe, Asia, the Middle
East, Africa and Oceania. Use in other areas
may result in poor reception. The RDS (radio
data system) function only operates in areas
with broadcasting RDS signals for FM stations.

CAUTION

! Do not allow this unit to come into contact

with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with
liquids.

! The Pioneer CarStereo-Pass is for use only in

Germany.

! Always keep the volume low enough to hear

outside sounds.

! Avoid exposure to moisture.

! If the battery is disconnected or discharged,

any preset memory will be erased.

Note

Function setting operations are completed even
if the menu is canceled before the operations
are confirmed.

About this manual

! In the following instructions, USB memories

and USB audio players are collectively re-
ferred to as

“USB storage device”.

In case of trouble

Should this unit fail to operate properly, please
contact your dealer or nearest authorized
PIONEER Service Station.

Head unit

a

b

4

7

1 2 3

5

9

8

c

6

Part

Part

1

SRC/OFF

7

BAND

2

MULTI-CONTROL
(

M.C.)

8

(back)/

DIMMER
(dimmer)

3

(list)

9

c/d

4

DISP

a

1/

to

6/

5

USB port

b

AUX input jack
(3.5 mm stereo
jack)

6

(equalizer)

c

Detach button

CAUTION

! Use an optional Pioneer USB cable (CD-

U50E) to connect the USB storage device as
any device connected directly to the unit will
protrude out from the unit, which could be
dangerous.

! Do not use unauthorized products.

Display indication

2

1

3

7

5

9

4

6 8

a

Indicator

State

1

(list)

The list function is being oper-
ated.

2

Sub infor-
mation sec-
tion

Sub information is displayed.

3

TA (traffic
announce-
ments)

TA function is on.

4

TP (traffic
program
identifica-
tion)

A TP station is tuned in.

5

(sound re-
triever)

The sound retriever function
is on.

6

LOC

Local seek tuning is on.

7

(repeat)

Track or folder repeat is on.

8

(ran-

dom)

Random play is on.

Before you start

2

Section

Operating this unit

En

01

02

<QRB3391-A>2

Black plate (3,1)

Indicator

State

9

Main infor-
mation sec-
tion

! Tuner: band and fre-

quency

! RDS: program service

name, PTY information
and other literal informa-
tion

! USB storage device:

elapsed playback time
and text information

a

Appears when a lower tier of
folder or menu exists.

Set up menu

When you turn the ignition switch to ON after in-
stallation, set up menu appears on the display.
You can set up the menu options below.

1

After installation of this unit, turn the

ignition switch to ON.
SET UP appears.

2

Turn M.C. to switch to YES.

# If you do not operate for 30 seconds, the set up
menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to

NO. Press to select.

If you select

NO, you cannot set up in the set up

menu.

3

Press M.C. to select.

4

Perform the following procedures to set

the menu.
To proceed to the next menu option, you need to
confirm your selection.

LANGUAGE (multi-language)

This unit can display the text information from a
compressed audio file even for information em-
bedded in English or Russian.
! If the embedded language and the selected

language setting are not the same, text infor-
mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

ENG (English)

—РУС (Russian)

2 Press M.C. to confirm the selection.

CLOCK SET (setting the clock)

1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-

ual tuning.

1 Turn M.C. to select the FM tuning step.

50 (50 kHz)

—100 (100 kHz)

2 Press M.C. to confirm the selection.

QUIT appears.

5

To finish your settings, turn M.C. to select

YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO. Press to select.

6

Press M.C. to select.

Notes

! You can set up the menu options from the

system menu. For details about the settings,
refer to System menu on page 7.

! You can cancel set up menu by pressing

SRC/OFF.

Basic operations

Important

! Handle gently when removing or attaching

the front panel.

! Avoid subjecting the front panel to excessive

shock.

! Keep the front panel out of direct sunlight

and high temperatures.

! To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached
to the front panel before detaching it.

Removing the front panel to protect your unit from
theft
1 Press the detach button to release the front

panel.

2 Push the front panel upward (M) and then pull

it toward (

N) you.

3 Always keep the detached front panel in a pro-

tection device such as a protection case.

Re-attaching the front panel
1 Slide the front panel to the left.

Make sure to insert the tabs on the left side of
the head unit into the slots on the front panel.

2 Press the right side of the front panel until it is

firmly seated.
If you cannot attach the front panel to the
head unit successfully, make sure that you are
placing the front panel onto the head unit cor-
rectly. Forcing the front panel into place may
result in damage to the front panel or head
unit.

Turning the unit on
1 Press SRC/OFF to turn the unit on.

Turning the unit off
1 Press and hold SRC/OFF until the unit turns

off.

English

Operating this unit

3

Section

Operating this unit

En

02

<QRB3391-A>3

Frequently used menu operations, Tuner, Operating this unit

Страница 4

• Изображение
• Текст

Black plate (4,1)

Selecting a source
1 Press SRC/OFF to cycle between:

TUNER (tuner)

—USB (USB)—AUX (AUX)

Adjusting the volume
1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when re-
moving the front panel.

Note

When this unit

’s blue/white lead is connected to

the vehicle

’s auto-antenna relay control termi-

nal, the vehicle

’s antenna extends when this

unit

’s source is turned on. To retract the anten-

na, turn the source off.

Frequently used menu
operations

Returning to the previous display
Returning to the previous list (the folder one level
higher)
1 Press

/

DIMMER.

Returning to the ordinary display
Canceling the main menu
1 Press BAND.

Returning to the ordinary display from the list
1 Press BAND.

Tuner

Basic operations

Selecting a band
1 Press BAND until the desired band (FM1,

FM2, FM3 for FM or MW/LW) is displayed.

Switching preset stations
1 Press c or d.
! Select PCH (preset channel) under SEEK to

use this function. For details about the set-
tings, refer to

SEEK (left/right key setting) on

page 5.

Manual tuning (step by step)
1 Press c or d.
! Select MAN (manual tuning) under SEEK to

use this function. For details about the set-
tings, refer to

SEEK (left/right key setting) on

page 5.

Seeking
1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing

c or d.
While pressing and holding c or d, you can
skip stations. Seek tuning starts as soon as
you release c or d.

Note

This unit

’s AF (alternative frequencies search)

function can be turned on and off. AF should be
off for normal tuning operation (refer to

AF (al-

ternative frequencies search) on page 5).

Storing and recalling stations
for each band

Using preset tuning buttons

1

When you find a station that you want

to store in memory, press one of the preset
tuning buttons (1/

to 6/

) and hold until

the preset number stops flashing.

2

Press one of the preset tuning buttons

(1/

to 6/

) to select the desired station.

Switching the display

Selecting the desired text information
1 Press DISP to cycle between the following:

! FREQUENCY (program service name or

frequency)

! BRDCST INFO (program service name/PTY

information)

! CLOCK (source name and clock)

Notes

! If the program service name cannot be ac-

quired in

FREQUENCY, the broadcast fre-

quency is displayed instead. If the program
service name is detected, the program serv-
ice name will be displayed.

! BRDCST INFO text information will change

automatically.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Using PTY functions

You can tune in to a station using PTY (program
type) information.

Searching for an RDS station by PTY information
You can search for general types of broadcasting
programs, such as those listed in the following
section. Refer to page 4.
1 Press

(list).

2 Turn M.C. to select a program type.

NEWS/INFO

—POPULAR—CLASSICS—

OTHERS

3 Press M.C. to begin the search.

The unit searches for a station broadcasting
that type of program. When a station is found,
its program service name is displayed.
! To cancel the search, press M.C. again.
! The program of some stations may differ

from that indicated by the transmitted PTY.

! If no station is broadcasting the type of

program you searched for,

NOT FOUND is

displayed for about two seconds and then
the tuner returns to the original station.

PTY list

NEWS/INFO (news and information)

NEWS (News), AFFAIRS (Current affairs), INFO
(Information),

SPORT (Sports), WEATHER (Weath-

er),

FINANCE (Finance)

POPULAR (popular)

POP MUS (Popular music), ROCK MUS (Rock
music),

EASY MUS (Easy listening), OTH MUS

(Other music),

JAZZ (Jazz), COUNTRY (Country

music),

NAT MUS (National music), OLDIES

(Oldies music),

FOLK MUS (Folk music)

CLASSICS (classics)

L. CLASS (Light classical), CLASSIC (Classical)

Operating this unit

4

Section

Operating this unit

En

02

<QRB3391-A>4

Seek (left/right key setting) on, Af (al, Usb storage device

Operating this unit

• Изображение
• Текст

Black plate (5,1)

OTHERS (others)

EDUCATE (Education), DRAMA (Drama), CUL-
TURE (Culture), SCIENCE (Science), VARIED (Var-
ied),

CHILDREN (Children

’s), SOCIAL (Social

affairs),

RELIGION (Religion), PHONE IN (Phone

in),

TOURING (Travel), LEISURE (Leisure), DOCU-

MENT (Documentaries)

Function settings

1

Press M.C. to display the main menu.

2

Turn M.C. to change the menu option

and press to select FUNCTION.

3

Turn M.C. to select the function.

Once selected, the following functions can be
adjusted.
# If MW/LW band is selected, only BSM, LOCAL
and

SEEK are available.

BSM (best stations memory)

BSM (best stations memory) automatically stores
the six strongest stations in the order of their sig-
nal strength.
1 Press M.C. to turn BSM on.

To cancel, press

M.C. again.

REGION (regional)

When AF is used, the regional function limits the
selection of stations to those broadcasting region-
al programs.
1 Press M.C. to turn the regional function on or

off.

LOCAL (local seek tuning)

Local seek tuning lets you tune in to only those
radio stations with sufficiently strong signals for
good reception.
1 Press M.C. to select the desired setting.

FM:

OFF

—LV1—LV2—LV3—LV4

MW/LW:

OFF

—LV1—LV2

The highest level setting allows reception of
only the strongest stations, while lower levels
allow the reception of weaker stations.

TA (traffic announcement standby)

1 Press M.C. to turn traffic announcement

standby on or off.

AF (alternative frequencies search)

1 Press M.C. to turn AF on or off.

NEWS (news program interruption)

1 Press M.C. to turn the NEWS function on or

off.

SEEK (left/right key setting)

You can assign a function to the left and right keys
of the unit.
Select

MAN (manual tuning) to tune up or down

manually or select

PCH (preset channel) to switch

between preset channels.
1 Press M.C. to select MAN or PCH.

USB storage device

Basic operations

Playing songs on a USB storage device
1 Open the USB port cover.
2 Plug in the USB storage device using a USB

cable.
Playback is performed automatically.

Stopping playback of files on a USB storage de-
vice
1 You may disconnect the USB storage device at

any time.
The unit stops playback.

Selecting a folder
1 Press 1/ or 2/ .

Selecting a track
1 Press c or d.

Fast forwarding or reversing
1 Press and hold c or d.
! When playing compressed audio, there is no

sound during fast forward or reverse.

Returning to root folder
1 Press and hold BAND.

Switching between playback memory devices
You can switch between playback memory devices
on USB storage devices with more than one Mass
Storage Device-compatible memory device.
1 Press BAND.
! You can switch between up to 32 different

memory devices.

Note

Disconnect USB storage devices from the unit
when not in use.

Switching the display

Selecting the desired text information
1 Press DISP to cycle between the following:

MP3/WMA/WAV
! TRACK INFO (track title/artist name/album

title)

! FILE INFO (file name/folder name)
! ELAPSED TIME (track number and play-

back time)

! CLOCK (source name and clock)
! SPEANA (spectrum analyzer)

Notes

! TRACK INFO and FILE INFO text information

will change automatically.

! Depending on the version of iTunes used to

write MP3 files to media file types, incompati-
ble text stored within an audio file may be
displayed incorrectly.

! Text information items that can be changed

depend on the media.

Selecting and playing files/
tracks from the name list

1

Press

to switch to the file/track name

list mode.

2

Use M.C. to select the desired file name

(or folder name).

Selecting a file or folder
1 Turn M.C.

Playing
1 When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the se-
lected folder
1 When a folder is selected, press M.C.

Playing a song in the selected folder
1 When a folder is selected, press and hold M.C.

English

Operating this unit

5

Section

Operating this unit

En

02

<QRB3391-A>5

Black plate (6,1)

Operations using special buttons

Selecting a repeat play range
1 Press 6/

to cycle between the following:

! ALL – Repeat all files
! ONE – Repeat the current file
! FLD – Repeat the current folder

Playing tracks in random order
1 Press 5/

to turn random play on or off.

Tracks in a selected repeat range are played in
random order.

! To change songs during random play, press d

to switch to the next track. Pressing c restarts
playback of the current track from the begin-
ning of the song.

Pausing playback
1 Press 4/PAUSE to pause or resume.

Enhancing compressed audio and restoring rich
sound (sound retriever)
1 Press 3/S.Rtrv to cycle between:

1

—2—OFF (off)

1 is effective for low compression rates, and 2
is effective for high compression rates.

Function settings

1

Press M.C. to display the main menu.

2

Turn M.C. to change the menu option

and press to select FUNCTION.
Once selected, the function below can be ad-
justed.

S.RTRV (sound retriever)

Automatically enhances compressed audio and
restores rich sound.
1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed
audio and restoring rich sound (sound retriever)
on page 6.

Audio adjustments

1

Press M.C. to display the main menu.

2

Turn M.C. to change the menu option

and press to select AUDIO.

3

Turn M.C. to select the audio function.

Once selected, the following audio functions
can be adjusted.

! FADER is not available when SUB.W/SUB.W

is selected in

SP-P/O MODE. For details, refer

to

SP-P/O MODE (rear output and preout set-

ting) on page 7.

! SUB.W, SUB.W CTRL and HPF SETTING are

not available when

REAR/REAR is selected in

SP-P/O MODE. For details, refer to
SP-P/O MODE (rear output and preout set-
ting) on page 7.

! SUB.W CTRL and HPF SETTING are not avail-

able when

SUB.W is selected in OFF. For de-

tails, refer to

SUB.W (subwoofer on/off

setting) on page 6.

FADER (fader adjustment)

1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the front/rear speaker bal-

ance.

BALANCE (balance adjustment)

1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the left/right speaker bal-

ance.

EQ SETTING (equalizer recall)

1 Press M.C. to display the setting mode.
2 Turn M.C. to select the equalizer.

POWERFUL

—NATURAL—VOCAL—CUS-

TOM1

—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be
customized when

CUSTOM1 or CUSTOM2 is

selected.
If selecting

CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting
other options, press

M.C. to return to the pre-

vious display.
! CUSTOM1 can be set separately for each

source.

! CUSTOM2 is a shared setting used in com-

mon for all sources.

3 Press M.C. to display the setting mode.
4 Press M.C. to cycle between the following:

Equalizer band

—Equalizer level

5 Turn M.C. to select the desired setting.

Equalizer band:

80HZ

—250HZ—800HZ—

2.5KHZ

—8KHZ

Equalizer level:

+6 to

–6

! You can also switch the equalizer by pressing

repeatedly.

LOUDNESS (loudness)

Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1 Press M.C. to select the desired setting.

OFF (off)

—LOW (low)—MID (mid)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to select the desired setting.

NOR (normal phase)

—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:

Cut-off frequency

—Output level—Slope level

Rates that can be adjusted will flash.

3 Turn M.C. to select the desired setting.

Cut-off frequency:

50HZ

—63HZ—80HZ—

100HZ

—125HZ—160HZ—200HZ

Output level:

–24 to +6

Slope level:

–6— –12

BASS BOOST (bass boost)

1 Press M.C. to display the setting mode.
2 Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or
decreased.

HPF SETTING (high pass filter adjustment)

When you do not want low sounds from the sub-
woofer output frequency range to play from the
front or rear speakers, turn on the HPF (high pass
filter). Only frequencies higher than those in the
selected range are output from the front or rear
speakers.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the following:

Cut-off frequency

—Slope level

3 Turn M.C. to select the desired setting.

Cut-off frequency:

OFF

—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ
Slope level:

–6— –12

Operating this unit

6

Section

Operating this unit

En

02

<QRB3391-A>6

Sp-p/o mode (rear output and preout set, System menu, Switching the dimmer setting

Initial menu, Operating this unit

• Изображение
• Текст

Black plate (7,1)

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! Settings are based on the FM volume level,

which remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to

SLA.

1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.

Adjustment range:

+4 to

–4

System menu

Important

PW SAVE (power saving) is canceled if the ve-
hicle battery is disconnected and will need to be
turned back on once the battery is reconnected.
When

PW SAVE (power saving) is off, depend-

ing on connection methods, the unit may con-
tinue to draw power from the battery if your
vehicle

’s ignition doesn’t have an ACC (acces-

sory) position.

1

Press M.C. to display the main menu.

2

Turn M.C. to change the menu option

and press to select SYSTEM.

3

Turn M.C. to select the system menu

function.
Once selected, the following system menu func-
tions can be adjusted.

LANGUAGE (multi-language)

This unit can display the text information from a
compressed audio file even for information em-
bedded in English or Russian.
! If the embedded language and the selected

language setting are not the same, text infor-
mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Turn M.C. to select the desired setting.

ENG (English)

—РУС (Russian)

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.
2 Press M.C. to select the segment of the clock

display you wish to set.
Hour

—Minute

3 Turn M.C. to adjust the clock.

12H/24H (time notation)

1 Press M.C. to select the desired setting.

12H (12-hour clock)

—24H (24-hour clock)

AUTO PI (auto PI seek)

The unit can automatically search for a different
station with the same programming, even during
preset recall.
1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary de-
vice connected to this unit.
1 Press M.C. to turn AUX on or off.

PW SAVE (power saving)

Switching this function on enables you to reduce
the consumption of battery power.
! Turning on the source is the only operation al-

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

Switching the dimmer setting

You can adjust the brightness of illumination.

1

Press M.C. to display the main menu.

2

Turn M.C. to display ILLUMI and press to

select.

3

Press M.C. to select the desired setting.

OFF (off)

—ON (on)

! You can also change the dimmer setting by

pressing and holding

/

DIMMER.

Initial menu

1

Press and hold SRC/OFF until the unit

turns off.

2

Press and hold SRC/OFF until the main

menu appears in the display.

3

Turn M.C. to change the menu option

and press to select INITIAL.

4

Turn M.C. to select the initial menu func-

tion.
Once selected, the following initial menu func-
tions can be adjusted.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-

ual tuning.

1 Press M.C. to select the FM tuning step.

50 (50 kHz)

—100 (100 kHz)

SP-P/O MODE (rear output and preout setting)

The rear speaker leads output and the RCA output
of this unit can be used to connect a full-range
speaker or subwoofer. Select a suitable option for
your connection.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.

You can select any one of the options in the fol-
lowing list:
! REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speak-
er leads output and there is a subwoofer
connected to the RCA output.

! SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear
speaker leads output without any auxiliary
amp and there is a subwoofer connected
to the RCA output.

! REAR/REAR – Select when there is a full-

range speaker connected to the rear speak-
er leads output and the RCA output.
If there is a full-range speaker connected to
the rear speaker leads output and the RCA
output is not used, you may select either
REAR/SUB.W or REAR/REAR.

System menu

1

Press and hold SRC/OFF until the unit

turns off.

2

Press and hold SRC/OFF until the main

menu appears in the display.

3

Turn M.C. to change the menu option

and press to select SYSTEM.

4

Turn M.C. to select the system menu

function.
Once selected, the following system menu func-
tions can be adjusted.
For details, refer to System menu on page 7.

English

Operating this unit

7

Section

Operating this unit

En

02

<QRB3391-A>7

Using an aux source, If an unwanted display appears, Connections

Operating this unit, Installation

• Изображение
• Текст

Black plate (8,1)

Using an AUX source

1

Insert the stereo mini plug into the AUX

input jack.

2

Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-
ting is turned on. For more details, refer to

AUX

(auxiliary input) on page 7.

Switching the display

Selecting the desired text information
1 Press DISP to cycle between the following:

! Source name
! Source name and clock

If an unwanted display appears

Turn off the unwanted display using the proce-
dures listed below.

1

Press M.C. to display the main menu.

2

Turn M.C. to change the menu option

and press to select SYSTEM.

3

Turn M.C. to display DEMO OFF and press

to select.

4

Turn M.C. to switch to YES.

5

Press M.C. to select.

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.

ON

S

T

A

R

T

O

FF

ACC position

No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 W to

8

W (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions
below.
— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring
that comes into contact with metal parts to
protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine
compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.
— Never cut the insulation of the power cable of

this unit in order to share the power with
other devices. The current capacity of the
cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this
cable to the system remote control of an ex-
ternal power amp or the vehicle

’s auto-anten-

na relay control terminal (max. 300 mA
12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna
booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.
Also, never connect it to the power terminal
of the auto antenna. Doing so may result in
battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,
high-current products such as power amps)
must be wired separately. If they are not, an
accidental detachment may result in a fire or
malfunction.

This unit

3

4

2

1

1 Power cord input
2 Rear output or subwoofer output
3 Antenna input
4 Fuse (10 A)

Operating this unit

8

Section

Installation

En

02

03

<QRB3391-A>8

Black plate (9,1)

Power cord

1

3

3

2

4

4

5

5

6

6

b

8

9

7

a

d

c

1 To power cord input
2 Depending on the kind of vehicle, the func-

tion of

3 and 5 may be different. In this

case, be sure to connect

4 to 5 and 6 to

3.

3 Yellow

Back-up (or accessory)

4 Yellow

Connect to the constant 12 V supply termi-
nal.

5 Red

Accessory (or back-up)

6 Red

Connect to terminal controlled by ignition
switch (12 V DC).

7 Connect leads of the same color to each

other.

8 Black (chassis ground)

9 Blue/white

The pin position of the ISO connector will dif-
fer depending on the type of vehicle. Connect
9 and b when Pin 5 is an antenna control
type. In another type of vehicle, never con-
nect

9 and b.

a Blue/white

Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).

b Blue/white

Connect to auto-antenna relay control termi-
nal (max. 300 mA 12 V DC).

c Speaker leads

White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left + or subwoofer +
Green/black: Rear left * or subwoofer *
Violet: Rear right + or subwoofer +
Violet/black: Rear right * or subwoofer *

d ISO connector

In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.

Notes

! Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout set-
ting) on page 7.
The subwoofer output of this unit is monau-
ral.

! When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.

Power amp (sold separately)

Perform these connections when using the op-
tional amplifier.









1

3

2

4

5

5

1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)
3 Connect with RCA cables (sold separately)
4 To Rear output or subwoofer output
5 Rear speaker or subwoofer

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires

drilling of holes or other modifications to the
vehicle.

! Do not install this unit where:

— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result

of a sudden stop.

! The semiconductor laser will be damaged if

it overheats. Install this unit away from hot
places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

! When installing, to ensure proper heat dis-

persal when using this unit, make sure you
leave ample space behind the rear panel and
wrap any loose cables so they are not block-
ing the vents.

5cm

cm

Leave ample

space

5 cm

5 cm

DIN front/rear mount

This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.

DIN Front-mount

1

Insert the mounting sleeve into the dash-

board.
For installation in shallow spaces, use the sup-
plied mounting sleeve. If there is enough space,
use the mounting sleeve that came with the ve-
hicle.

2

Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into
place.

1

2

1 Dashboard

English

Installation

9

Section

Installation

En

03

<QRB3391-A>9

Troubleshooting, Error messages, Installation

Additional information

• Изображение
• Текст

Black plate (10,1)

2 Mounting sleeve

# Make sure that the unit is installed securely in
place. An unstable installation may cause skipping
or other malfunctions.

DIN Rear-mount

1

Determine the appropriate position

where the holes on the bracket and the side
of the unit match.

2

Tighten two screws on each side.

1

2

3

1 Tapping screw (5 mm × 8 mm)
2 Mounting bracket
3 Dashboard or console

Removing the unit

1

Remove the trim ring.

1 Trim ring
2 Notched tab
! Releasing the front panel allows easier ac-

cess to the trim ring.

! When reattaching the trim ring, point the

side with the notched tab down.

2

Insert the supplied extraction keys into

both sides of the unit until they click into
place.

3

Pull the unit out of the dashboard.

Removing and re-attaching the front
panel

You can remove the front panel to protect your
unit from theft.
Press the detach button and push the front
panel upward and pull it toward you.
For details, refer to Removing the front panel to
protect your unit from theft and Re-attaching the
front panel on page 3.

Troubleshooting

Symptom

Cause

Action

The display
automatically
returns to the
ordinary dis-
play.

You did not per-
form any opera-
tion within
about 30 sec-
onds.

Perform operation
again.

The repeat
play range
changes un-
expectedly.

Depending on
the repeat play
range, the se-
lected range
may change
when another
folder or track is
being selected
or during fast
forwarding/re-
versing.

Select the repeat
play range again.

A subfolder is
not played
back.

Subfolders can-
not be played
when

FLD (fold-

er repeat) is se-
lected.

Select another re-
peat play range.

NO XXXX ap-
pears when a
display is
changed (

NO

TITLE, for ex-
ample).

There is no em-
bedded text in-
formation.

Switch the display
or play another
track/file.

The unit is
malfunction-
ing.
There is inter-
ference.

You are using a
device, such as
a cellular
phone, that
transmits elec-
tric waves near
the unit.

Move electrical
devices that may
be causing the in-
terference away
from the unit.

Error messages

When you contact your dealer or your nearest
Pioneer Service Center, be sure to note the error
message.

Common

Message

Cause

Action

AMP ERROR

Unit fails to op-
erate or speaker
connection is
incorrect; pro-
tective circuit is
activated.

Check the speak-
er connection. If
the message fails
to disappear even
after the engine is
switched off/on,
contact your deal-
er or an author-
ized Pioneer
Service Station
for assistance.

USB storage device

Message

Cause

Action

FORMAT
READ

Sometimes
there is a delay
between the
start of playback
and when you
start to hear any
sound.

Wait until the
message disap-
pears and you
hear sound.

NO AUDIO

There are no
songs.

Transfer the audio
files to the USB
storage device
and connect.

The connected
USB storage de-
vice has secur-
ity enabled.

Follow the USB
storage device in-
structions to dis-
able the security.

Installation

10

Section

Additional information

En

03

<QRB3391-A>10

Комментарии

• Главная
• Продукция
• Автомобильные ресиверы
• Support for MVH-150UBG

Главная

♥ В закладки

Просмотр инструкции в pdf

Инструкция по эксплуатации автомагнитолы Pioneer MVH-150UBG.

Скачать инструкцию к автомагнитоле Pioneer MVH-150UBG (1,19 МБ)

Автомагнитолы

« Инструкция к автомагнитоле Pioneer DEH-1800UBA

» Инструкция к автомагнитоле Kenwood DDX155

Вам также может быть интересно

Инструкция к автомагнитоле Pioneer DEH-S101UB

Инструкция к кухонным весам Pioneer PKS1011

Инструкция к наушникам Pioneer HDJ-S7-W

Инструкция к автомагнитоле Pioneer SPH-DA120

Инструкция к автомагнитоле Pioneer DMH-G220BT

Инструкция к автомагнитоле Pioneer DEH-X5900BT

Инструкция к наушникам Pioneer SE-LTC3R-W

Инструкция к автомагнитоле Pioneer DVH-780AV

Добавить комментарий

Имя *

Email *

Сайт

Комментарий

Сохранить моё имя, email и адрес сайта в этом браузере для последующих моих комментариев.

• Добавить инструкцию
• Заказать инструкцию