Ref542plus abb руководство по эксплуатации

• 92, ABB REF 542plus A080290 Fig. 20.6.4.-1 Communication subpage visua lization When the port is not installed or configured, the following page will be displayed. A051642 Fig. 20.6.4.-2 Communication module is not installed 20.6.4.1. IEC 103 communication page When the IEC 60870-5-103 communication module is installed the following page is displayed. 92 REF 542plusREF 542plus Multifunction Protection and Switc…

• 104, A080296 Fig. 20.6.4.8.-5 General Info subpage To move from one subpage to another click the UP , and DOWN buttons. You can go back to the FB COM Ethernet page from each subpage by clicking the MENU button. TCP/IP subpage The TCP/IP subpage consists of two pages for each configured communication port, port1 or port2. The following two figures Fig. 20.6.4.8.-6 and Fig. 20.6.4.8.-7 show th…

• 14, A051328 Fig. 3.1.-1 HMI control area This section of the display shows the Single Line Diagram (SLD) of the controlled panel and the measurement bars. Text can be added in this section to improve the understanding of SLD. * Command buttons The Primary Object Control can be performed with the following push buttons to allow operating the primary objects if configured as …

• 63, 63 A051438 2 Fig. 16.1.-4 HMI is polling the Base unit addresses Select the HMI <-> Base Unit address to change the address to be polled. A051439 2 Fig. 16.1.-5 Changing the Base Unit address to be polled. HMI Self Test Only with the older version of the HMI V4, the HMI can be tested without connection to the base unit. The test must be done by using the foreseen menu item on the …

• 59, 59 A051366 Fig. 15.3.1.-3 Changing the Base Unit address from the HMI Please note: When the ALARM LED is on, the download is inhibited. The configuration download starts as soon as the relevant push button on the Operating Tool is clicked. The previous configuration inside REF 542plus is destroyed and overwritten by the new one. REF 542plus is fully operational during the downloa…

• 134, ABB REF 542plus ABB Oy Distribution Automation P.O. Box 699 FI-65101 Vaasa FINLAND +358 10 22 11 +358 10 22 224 1094 http://www.abb.com/substationautomation 1MRS755869 EN 12/2008
  …

• 42, Usually, the SCADA transmits to the unit the time and date according to the used protocol services. There are some differences depending on the used protocol. * IEC 60870–5–103 protocol: The IEC 60870–5–103 module is the time master. Setting the time and date from the HMI is inhibited. * LON LAG 1.4 protocol: The LON module is the time master. Setting the time and …

• 25, 25 6. Control modes 6.1. Available control modes Local Control It is possible to control the circuit breaker and other primary objects from the HMI using the object control buttons. Open and close operations are possible only if the interlocking logic programmed into the unit allow them. Remote control from the SCADA is inhibited. Uploading and downloading the configuration via the optical interf…

• 53, ABB REF 542plus 53 A051360 Fig. 14.6.-1 Optical inputs commission ing page 14.7. Optical output commissioning page This page allows driving the optical output on the main module (only type 1VCF751021R801). Line description: “Channel descriptor”“Channel number “: “Values” Channel descriptor: Optical output Channel number: x. Where x addresses the optical output channel. Values: 0: Optical output is off…

• 88, A051463 Fig. 20.6.-1 Service page menu The service page contains the following submenus. 20.6.1. Statistics This submenu shows the FUPLA cycle time and other information related to the current configuration in the unit. A051464 Fig. 20.6.1.-1 Statistics submenu 20.6.2. Versions This submenu displays information on the firmware versions loaded inside the unit. 88 REF 542plusREF 542…

• Lenovo Flex System SI4091 10Gb System InterconnectModuleProduct GuideThe Lenovo® Flex System SI4091 10Gb System Interconnect Module enables simplified, low-cost integrationof Flex System™ into your networking infrastructure.The SI4091 requires no management for most data center environments, which eliminates the need toconfigure each networking device or individual ports, thus reducing …

  Flex System SI4091 10Gb 17

• 3A3229BENKit InstructionsPR70™ Solenoid Valve Upgrade KitFor replacing the air cylinder solenoid valve on all PR70 fixed or variable ratio systems that meter, mix, and dispense two-component materials. For professional use only. Part No. 17J520100 psi (0.7 MPa, 7 bar) Maximum Air Inlet PressureImportant Safety InstructionsRead all warnings and instructions in this manual and in …

  PR70 Series 8

• ® STAM-1 TRNK stam1trnk_e_09/05 The STAM-1 TRNK card is used for expansion of functional capabilities of the STAM-1 monitoring station. It enables a trunking radiotelephone, which supports the MAP27 data transfer protocol, or the SATEL GSM module (GSM LT-1, GSM-4), to be connected to the station, thus making monitoring possible by radio (radiotelephone), by means …

  STAM-1 TRNK 2

Copyright

1VTA100114-Rev. 04 en

Valid from Version V4D02

Multifunction Protection and Switchgear Control unit REF542plus

Manual: Motor Protection with ATEX-Certification

We reserve all rights to this document, even in the event that a patent is issued and a

different commercial proprietary right is registered. Improper use, in particular repro-

duction and dissemination to third parties, is not permitted.

This document has been carefully checked. if the user nevertheless detects any er-

rors, he is asked to notify us as soon as possible.

The data contained in this manual is intended solely for the product description and is

not to be deemed to be a statement of guaranteed properties. In the interests of our

customers, we constantly seek to ensure that our products are developed to the latest

technological standards.

As a result, it is possible that there may be some differences between the hard-

ware/software product and this information product.

CE Conformity Declaration

The product „ Multifunctional Protection and Bay Control Unit REF542plus» is de-

signed and manufactured complying to the corresponding international standards of

the series EN 50081, EN 50082 for EMC-Guidelines and EN 60255-6 for Low Voltage

Directive of the European Parliament and Council

PTMV, 19.01.05

Motorprotection

2 / 66