Руководство настройка kaon kcf k220 sco форум

Quick Links

• Page 2: General Safety

  General Safety Warning Always follow these instructions to avoid the risk of injury to yourself or damage to your equipment. Unplug the receiver from the AC power outlet before cleaning. Use only a damp cloth for cleaning the exterior of the receiver. Do not use accessories or attachments not recommended by the receiver manufacturer as they may cause problems to the equipment and will void the warranty.

• Page 3
  General Safety Route power supply cord so that are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to the cords that plugs in the convenience receptacles, and the point where they exit from the unit. Use an outlet that contains surge suppression or ground fault protection.
• Page 4
  DIGITAL CABLE RECEIVER OWNER’S MANUAL SIMPLE & SPEEDY OPERATION HANDBOOK Before operation, Please read the entire manual thoroughly and retain it for future reference.
• Page 5
  ▷ Class B digital device NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• Page 6
  Channel List Edit Channel List Program Guide System Setting Automatic Search Manual Search CA System (Option) Utility (Option)

• Page 7: Table Of Contents

  Contents Remote Control Unit Front Panel Rear Panel Connecting Your Equipment Basic Operation Menu Guide Main Menu Channel Search Channel List Edit Channel List Program Guide System Setting Menu Language Audio Language Subtitle Language SCART Output Screen Type Banner Time RF Mode RF Channel DIGITAL CABLE RECEIVER…

• Page 8
  Contents Local Time Menu Transparency Change PIN Code Parental Lock Receiver Lock S/PDIF Output (Option) Auto Power Factory Reset System Information CA System (option) Utility (option) Troubleshooting Technical Specifications Menu Map DIGITAL CABLE RECEIVER…

• Page 9: Remote Control Unit

  Remote Control Unit STAND BY NUMERIC BUTTON TV/RADIO TV/STB CH UP/DOWN VOL UP/DOWN MUET PAUSE UP/DOWN LEFT/RIGHT MENU EXIT GREEN YELLOW SUBTITLE(RED) INFO(BLUE) P.STD A L/R P.SIZE TEXT RECALL A.LANG SLEEP Note! 1: When inserting batteries, make sure that the polarity (+/-) is correct. Note! 2: The design of the Remote Control Unit may be changed without any notice in advance.

• Page 10
  Remote Control Unit 1 STAND BY To switch between operation and stand by mode. 2 NUMERIC BUTTONS To select the channel and enter the channel edit and PIN code . 3 CH UP / DOWN To move up or down on the menu. 4 VOL UP / DOWN To move up or down on the menu.

• Page 11: Front Panel

  Front Panel 1.POWER(STAND BY): Switch the receiver power “ON” or “OFF”. 2. CH Up/Down : Channel Up/Down or select item of sub-menu. 3.SEG. DISP.: 4-digit 7-segment display channel information. 4.Smartcard Slot(Option): 1Slot for Smartcard DIGITAL CABLE RECEIVER…

• Page 12: Rear Panel

  Rear Panel 1. POWER SUPPLY 90 ~ 260V AC, 50/60Hz. 2. VIDEO Video connection port to the TV or other equipment. 3. AUDIO Audio connection port to the TV or other equipment. 4. RS-232 To connect to a personal computer for software upgrade. 5.

• Page 13: Connecting Your Equipment

  Connection Your Equipment How to connect your STB to various systems There are several ways of connecting the STB to your TV and/or Hi-Fi SYSTEM. Consult your local supplier for assistance in setting-up your system that is best suited to your requirements. 1.

• Page 14
  Connecting Your Equipment 3. Connect STB to a Digital Audio System If you have a DAC with S/PDIF coaxial cable input, you can connect the STB with it to enjoy higher quality sound. Connect S/PDIF coaxial cable to a digital amplifier. 4.
• Page 15
  Connection Your Equipment TV with Terrestrial Antenna 1. Connect one end of RCA/Cinch cable to the RCA/Cinch jack on the back of the STB and the other end to a RCA/Cinch jack on your TV. If your TV doesn’t have a RCA/Cinch jack, connect one end of RF cable to the TV OUT on the back of the STB and the other end to a RF input jack on your TV.
• Page 16
  Connecting Your Equipment Reference 1. Upgrade via Personal Computer To maintain the STB up-to-date, it will be possible to upgrade the software of the STB via STB and personal computer. New versions of the software may include new or improved functions for the latest update. 1.
• Page 17
  Connection Your Equipment Front Panel Display Message KEY & DISPLAY The message of the 7-segment LED (Light-Emitting Diode) on the STB and keys are explained as below. Current program number on TV list Standby Mode Current program number on RADIO list System Booting TV Mode Power Off…

• Page 18: Basic Operation

  Basic Operation Basic Function 1. Program Information After the television channels have been programmed, you will see the information box each time you change the channels. 1. Every time you change channels you will receive program information for a few seconds. (In the “Banner Time” menu you can select how long this information will be shown.) 2.

• Page 19: Basic Function

  Basic Operation Basic Function 4. Channel-Information Banner 1. During “Channel Banner” is appearing, when you press INFO(BLUE) Button, you can get “Channel-Information Banner”. 2. Using “Channel-Information Banner”, you can get a detailed channel listing Information. 5. Volume Control/Mute 1. To control audio volume, press LEFT/RIGHT( / ) buttons. 2.

• Page 20
  Basic Operation Basic Function 7. Timer The user can reserve a desired program at a desired time by using the Timer function. Pressing the YELLOW button in AV mode will open the Timer Window. 1. Daily, Weekly, Monthly Reservation. Use the UP/DOWN( ), LEFT/RIGHT( / ) buttons in the Timer Setting screen to select the date and time.
• Page 21
  Basic Operation Basic Function 9. Soundtrack 1. When you want to change the Audio Language of current channel, press the A/LANG button on the remote control. The on-screen menu is displayed on the left side of the screen. 2. Use UP/DOWN( ) buttons to choose the audio you want.
• Page 22
  Basic Operation Memo DIGITAL CABLE RECEIVER…

• Page 23: Easy Installation

  Basic Operation Easy Installation Before you can view the television or radio program, you must perform the installation procedure first. Therefore you will see only “Easy Installation Menu” at first when you plug in your system. The Easy Installation gives you the convenience of selecting various languages, adjusting the time and channel search.

• Page 24
  Basic Operation Easy Installation Language The first option is “Language Select” to select the desired language of the Menu, Audio, or Subtitle. Place the cursor on the sub menu by pressing the keys and press the OK( ) button to change language. The Language of Menu, Audio, or Subtitle will be changed to the selected language.

• Page 25: Menu Guide

  Menu Guide Main Menu Press the MENU button on the remote control unit. You will see the “Main Menu” on the screen 1. You can move into the desired submenu using UP/DOWN( ) buttons. 2. You should enter the PIN code in order to move into the corresponding submenu in case of “Edit Channel List or “System Setting”.

• Page 26: Channel Search

  Menu Guide Channel Search Select Automatic/Manual channel search in main menu. Automatic Search 1. Press Automatic Search in Main Menu. 2. Input a proper Start Frequency of the cable signal using NUMERIC buttons . 3. Input a proper End Frequency of the cable signal using NUMERIC buttons . 4.

• Page 27: Manual Search

  Menu Guide Channel Search Manual Search 1. Press Manual Search in Main Menu. 2. Input a proper Frequency of the cable signal using NUMERIC buttons . 3. Input a proper Symbol Rate of the cable signal using NUMERIC buttons . 4.

• Page 28: Channel List

  Menu Guide Channel List This menu helps you to easily select the channel that you want to watch. You can see the channel list when you had searched before. To use this menu, you should set channel group you want in the channel control menu.

• Page 29: Edit Channel List

  Menu Guide Edit Channel List From these menus, You can create favorite lists, lock, skip, delete, or move channel. 1. Select “Edit Channel List” in the main menu with UP/DOWN( ) buttons and press OK( ) button. 2. At the request window, Input PIN code. If you have not entered your own PIN code, then the PIN code 0000 applies, which was set at the factory.

• Page 30
  Menu Guide Edit Channel List 1. Favorite 1 ~ 8(Option) 1. You can edit favorite TV and Radio list. This enables you to create the 8 favorite TV and Radio lists. 2. Select the channel you want to edit favorite list and press OK( ) button.
• Page 31
  Menu Guide Edit Channel List 4. Skip 1. You can skip TV or Radio channel from the current list. 2. Select the channel you want to skip and press OK( ) button. 3. To recover the skipped channel, press the OK( ) button from edit list.

• Page 32: Program Guide

  Menu Guide Program Guide The program guide supplies information such as program listings and ending times for all available programs. 1. Select “Program Guide” in the main menu with UP/DOWN( ) buttons and press OK( ) button. In the viewing program, when you press the EPG button, you can get this view.

• Page 33: System Setting

  Menu Guide System Setting You will be asked to enter your PIN code before you can enter this menu. The PIN code preset to 0000 from the factory. The code can be changed from the “Change PIN Code” menu. Refer to page 30. If you want to customize the system to suit you better, you can specify some settings from the submenus in the “System Setting”…

• Page 34: Subtitle Language

  Menu Guide System Setting 3. Subtitle Language In this menu You can change default language for subtitle when changing services. 1. Use the UP/DOWN( ) buttons to move to language you want and then press OK( ) button. You can choose the language from a selection of English, Spanish, Finnish, Norwegian, Swedish, German, French and etc.

• Page 35: Banner Time

  Menu Guide System Setting 6. Banner Time When you switch channels, an information banner will be shown for a few seconds. You can select for how long the banner will be shown. 1. Select the banner time you want and then press OK( ) button.

• Page 36: Local Time

  Menu Guide System Setting 9. Local Time You can set your local time according to your location. 1. To set year, month and date, press UP/DOWN( ) buttons. The Calendar pop up window will be displayed. Select year using SUBTITLE(RED) and GREEN button. Select month using YELLOW and INFO(BLUE) button.

• Page 37: Parental Lock

  Menu Guide System Setting 12. Parental Lock When you change “Parental Lock” to “On” or “Off”, service channel can get or not from that set values. If you select “On”, you may need PIN code every time you select the lock channel program as you set in the channel control.

• Page 38: Auto Power

  Menu Guide System Setting 16. Auto Power (option) 1 . If the Auto Power is set to On and power is off, the Set turns on automatically and turns into the channel mode which you were watching before power breakdown. 2.

• Page 39: Ca System (Option)

  Menu Guide CA System (Option function) The menus are provided by Smartcard. Your receiver is equipped with one Smartcard slot, Plug in the appropriate a valid Smartcard. You will then have access to the respective scrambled and Pay-Per-View services. Insert the Smartcard into the Smartcard Slot on the front panel. The Smartcard determine the programs that can be de-scrambled.

• Page 40: Utility (Option)

  Menu Guide Utility (Option function) 1. Game 1. Select «Game» in the Utility menu with UP/DOWN( ) buttons and press LEFT/RIGHT( / ) button. 2. Select the game you want to play and press OK( ) button, and then you can play the game.. Tetris Hexa Puzzle…

• Page 41
  Menu Guide Utility (Option function) 4. Zoom Select “Zoom» in the Utility menu with UP/DOWN( ) button and press OK( ) button, 5. Calculator Select “Calculator» in the Utility menu with UP/DOWN( ) button and press OK( ) button, you can see the Calculator. DIGITAL CABLE RECEIVER…

• Page 42: Troubleshooting

  Troubleshooting Problem Solution No display LED on the front panel. Power cord plug in correctly. No power supply No Picture Ensure that the STB is switched on. Check connection and correct. Check channel and video output and correct. Poor picture quality Check the signal level, if this is low then try adjusting the Alignment of your dish.

• Page 43: Technical Specifications

  Technical Specifications Tuner Demodulation Constellation 16, 32, 64,128, 256 Input Connector IEC 169-24, Female(75 Ohm) Frequency Range 51MHz ~ 858MHz Symbol Rate 0.87 ~ 11.7 Mbaud RF Modulator PLL type UHF(CH 21~69) or VHF(CH 3~4) for the modulation TV Standard PAL B/G, I, D/K, NTSC M selectable RF Connector 75 Ohms, 169-2, Male/Female…

• Page 44: Power Supply

  Technical Specifications A/V & Data Input/Output Video RCA/Cinch, Video Output(CVBS)/SCART(CVBS,RGB). RCA/Cinch Volume & Mute Control Audio (Resolution: 20 bits DAC, Max 2Vrms) S/PDIF of Dolby Digital Bitstream Out RS-232C Transfer rate 115Kbps, 9 PIN D-Sub Type System Resources Flash Memory 1Mbyte, 2Mbytes (Optional) SDRAM 8Mbytes, 16Mbytes (Optional)

• Page 45: Menu Map

  Menu Map Main Menu Menu Language Channel List Audio Language Subtitle Language Edit Channel List SCART Output Screen Type Program Guide Banner Time System Setting RF Mode RF Channel Automatic Search Local Time Menu Transparency Manual Search Change PIN Code Parental Lock CA System SPDIF Output…

• Page 46
  102675…

Приобрели по распродаже в Контур-М небольшую партию каб. ресиверов kaon kcf-h220sco s/w
v13.05.11 h/w v32.D0.95  Loader V6.1.9, не открываются кодированные
каналы, кодировка ставропольского завода сигнал Cerber Crypt на
других приставках все работает. По всей видимости нужна более ранняя прошивка этого бокса. Гугление в поисках прошивки не помогает. Хотя у продавцов он заявлен как совместимый с данной кодировкой.

Записан

Брал у них же, все работает. Правда у меня DVCrypt, но это тоже самое что CerberCrypt.

Скинул на мыло прошивку которая у меня работает.

« Последнее редактирование: 16.02.2010, 11:42 от Rus »

Записан

Что-то боюсь, что прошивка не поможет. По-моему, там дело в том, что выдаёт церберовское оборудование — они вроде как конаксовый дескриптор перестали гнать. Но вот тут могу ошибиться. Прошивку посмотрю чуть позднее какая у меня есть.

Записан

По всем вопросам писать на e-mail, или через мессенджеры по номеру телефона.

Похоже на то что говорит Алексей CAS ID дескриптор другой стали гнать железо недавно брали вот и финт вылез. Предлагайте ваши варианты или возврат вендору делать?

Записан

Ну CasID поменять в системе не проблема. Вопрос будут ли другие приставки работать после этого.

Записан

По всем вопросам писать на e-mail, или через мессенджеры по номеру телефона.

А каким образом его поменять чтобы был DV cryptoВЫЙ дескриптор? Я конечно еще сильно не вникал в такие подробности но по всей видимости заменой ПО или я ошибаюсь?

Записан

При установке лицензии там вроде есть окошко, где оно указывается оно.

Записан

По всем вопросам писать на e-mail, или через мессенджеры по номеру телефона.

Всем добрый день.
В октябре прошлого года тестировали DVCrypt и все работало с приемниками  kaon kcf-h220sco и Topfield 6000, 6100. Приобрели лицензию и пробуем запустить коммерческую эксплуатацию. Каоны не работают с лицензией DVCrypt в то время как Topfield работает. Приемник kaon kcf-h220sco рекомендован разработчиком как работающий с этой системой. Разработчик рекомендовал сменить CAS ID  в установке лицензии. Поставил CAS ID CONAX. Ситуация стала зеркальной. Перестал работать Topfield, kaon заработал. Разработчик уверяет, что все дело в прошивке приемника.
Есть ли опыт у кого в этой ситуации?

Записан

У нас работают и те и другие приемники. Все дело в кривых ручках.

Записан

Я и прошу помощи исправить кривые ручки. Очень хочется иметь прямые ручки.
С уважением и надеждой на помощь.

Записан