Visonic next mcw k9 mcw инструкция

ENVIRONMENTAL

RFI Protection: >20 V/m up to 1000 MHz.

Operating Temperatures: -10

Storage Temperatures: -20

Compliance with Standards: Designed to meet FCC Part 15

and Directive 1999/5/EC of the European Parliament.

3.1 General Guidelines

3.2 Illustrated Installation Procedure

1

Disassemble the unit

C

SHIFT COVER

UP TO FREE

TOP TOOTH

AND

REMOVE

COVER

PULL OUT LOWER

EDGE OF COVER

3

Open holes in the base

TOP

CATCH

FOR PCB

CORNER

(2 OF 4)

SURFACE

(1 OF 2)

SUPPORTS

BREAK-AWAY

FOR BOTTOM

SEGMENT (BACK TAMPER

EDGE OF PCB

SWITCH ACTUATOR — OPTION)

Attention! Lean the rear part of the break-away segment against a

piece of wood while piercing its knockouts.

2

C to 50

C (14

F to 122

F).

°

°

°

°

C to 60

C (-4

F to 140

F).

°

°

°

°

LOOSEN

A

B

USE A LARGE

DIAMETER DRILL

BIT TO DE-BURR

THE OTHER SIDE

A

USE A SCREWDRIVER TO PIERCE

SURFACE OR CORNER KNOCK-

OUTS, AS REQUIRED.

PHYSICAL

Size (H x W x D): 94.5 x 63.5 x 53.0 mm (3-11/16 x 2-1/2 x 2-1/16″).

Weight (with battery): 70 g (2.5 oz).

Color: White.

PATENTS: U.S. Patents 5,693,943

(another patent pending).

2

Install the battery

FLEX

D

CATCH

OUT

OBSERVE

POLARITY !

FRONT

TAMPER

SWITCH

SCREW

4

Mount the base

1.8 — 2.4 m (6 — 8 ft) above ground

Recommended height up to 2.1 m (7 ft)

SINGLE-

SIDE, 45°

ANGLED

MOUNT

SURFACE

MOUNT

(1 OF 2)

Attention! The unit has a back tamper switch (option) under the PCB. As

long as the PCB is seated firmly within the base, the switch will be pressed

against a metal spring piece attached to the base.

Be sure to fasten the break-away segment to the wall with the screws

going through the metal spring and break-away base segment. If the

detector is forcibly removed from the wall, this segment will break away

from the base, causing the tamper switch to open and send a tamper alarm.

6,211,522

RESET: With the battery in

A

place, press both tamper

switches simultaneously

and r eleas e t hem. The

LED at the front will flash

for about 2 minutes until

t he det ec t or sta bi l i zes .

Note: The de]tector transmits

a low battery signal upon

detection of low battery.

Note: It is recommended to wait

about 1 minute before inserting

the new battery.

E NR OLL: Approach the

B

control panel and enroll the

detector’s ID into the control

panel’s memory as shown in

the panel’s installation

manual. When required to

transmit, press both tamper

switches again and release

BACK

them.

TAMPER

SWITCH

You may enroll the detector’s

(OPTION)

ID while the detector’s LED

flashes.

SINGLE-

SIDE, 45°

ANGLED

MOUNT

BREAK-AWAY

SEGMENT

D445,709

FOR TAMPER PROTECTION,

A

THE BREAK-AWAY SEGMENT

MUST BE ATTACHED TO

WALL.

MARK TWO DRILLING

B

POINTS AND DRILL HOLES

IN WALL.

INSERT TWO DOWELS AND

C

ATTACH THE BASE TO THE

WALL WITH TWO SCREWS.

INSERT THE BOTTOM EDGE

D

OF THE LARGE P.C. BOARD

UNDER THE TABS & PRESS

THE TOP EDGE IN.

DE3592

Detail Specifications: 199/199717-k985_mcw.pdf file (23 Feb 2023)

Accompanying Data:

Visonic K9-85 MCW Security System PDF Installation Instructions (Updated: Thursday 23rd of February 2023 05:49:32 PM)

Rating: 4.3 (rated by 19 users)

Compatible devices: KF-235 PG2, SR-730 PG2, POWERMASTER-10, POWERMAX PRO, MCS-720B, PowerG SR-740 PG2, PowerMaster-33 G2, PowerMax Partitions II.

Recommended Documentation:

Text Version of Installation Instructions

(Ocr-Read Summary of Contents, UPD: 23 February 2023)

Recommended Instructions:

IODIGITAL T9212, P4320, 3600-series, KEYTIS 4

• 

• 

• 

• 

• 

• 

• 

Additional Information:

Popular Right Now:

Operating Impressions, Questions and Answers:

Table of Contents for Visonic K9-85 MCW:

Questions, Opinions and Exploitation Impressions:

You can ask a question, express your opinion or share our experience of Visonic K9-85 MCW device using right now.

«NEXT K9-85 MCW» — беспроводной цифровой инфракрасный датчик, 9 х 9 м, 90 град., защита от животных с массой до 36 кг.

Особенности:

инструкция на «NEXT K9-85 MCW» (pdf) — 235.4 кб.

D-300058 1

NEXT PLUS MCW, NEXT PLUS K9-85 MCW

English

Wireless, PowerCode Digital PIR / Pet Immmune PIR

Detectors — Installation Instructions

Español

Detectores PIR Digital / Inmune a mascotas inalámbricos –

Instrucciones de instalación

Portuguese

Detector PIR Digital / Imune a Animais Via rádio – Instruções

de Instalação

GB/US: Walk-Test LED

SP: LED de modo de pruebas

PT: LED do teste de passagem

GB/US: Lens

SP: Lente

PT: Lente

Fig. 1 — NEXT PLUS MCW / NEXT PLUS K9-85 MCW

ENGLISH

1. INTRODUCTION

The NEXT PLUS MCW and NEXT PLUS K9-85 MCW (pet immune)

are microprocessor-controlled wireless digital PIR detectors.

NEXT is a registered mark of Visonic Ltd.

The detectors features are as follows:

• Combined Fresnel and cylindrical optics improves detection range,

up to 15 meters (40 ft), and false alarm immunity.

• NEXT PLUS MCW includes wall creep zone protection.

• In NEXT PLUS K9-85 MCW, Target Specific Imaging™ (TSI)

technology is used for distinction between human beings and pets

weighing up to 38 kg (85lb).

• Incorporates a fully supervised PowerCode transmitter.

• The advanced True Motion Recognition™ algorithm (patented)

allows distinguishing between the true motion of an intruder and any

other disturbances which may cause false alarms.

• Sophisticated frequency domain digital signal processing.

• No vertical adjustment is needed.

• An on-board motion event jumper determines whether 1 or 2

consecutive motion events trigger an alarm.

• Automatic termination of walk-test after 15 minutes.

• After detection, the detector disarms itself to save battery power. It

rearms (reverts to the ready state) if there is no subsequent

detection throughout the following 2-minute period.

• An optional version provides better protection for systems

compliant with DD243. After initial detection, the detector is

capable of 7 additional detections for a period of 5 minutes.

Further detection is possible only if no movement occurs during the

following 2 minutes. The detector will revert to the initial state if

there is no movement for an additional 5 minutes.

• Microprocessor-controlled temperature compensation.

• Sealed chamber protects the optical system.

• Front cover tamper switch. Option — Back tamper switch.

• White light protection.

For UL installations: The detector is for use with UL listed control

unit PowerMax+ only. Pet immunity has not been evaluated by UL.

2. SPECIFICATIONS

Detector Type: Dual element low-noise pyroelectric sensor.

Lens Data

No. of Curtain Beams / curtains:

NEXT PLUS MCW: 18 far, 18 mid, 10 close.

NEXT PLUS K9-85 MCW: 18 far, 18 mid, 18 close.

Max. Coverage: 15 x 15 m, (49 x 49 ft) / 90°

Pet Immunity (NEXT PLUS K9-85 MCW Only): Up to 38 kg (85 lb).

ELECTRICAL

Internal Battery: 3V Lithium battery, type CR-123A. For UL installations, use

Panasonic or Sanyo only.

Nominal Battery Capacity: 1450 mA/h.

Standby Current Drain: Approx. 0.025 mA.

Transmit Current Drain: 20 mA (including LED).

Battery Life (with LED on): Typically over 3 years.

Battery Power Test: Performed immediately upon battery insertion

and periodically after every several hours.

FUNCTIONAL

True Motion Event Verification: 2 position selector — 1 (OFF) or 2

(ON) motion events.

Alarm Period: 3 seconds.

Visual Indications:

LED Lights for about 3 seconds upon transmission of alarm &

tamper messages and upon motion detection in the walk test mode.

LED Flashes during the power-up stabilization period, or after

restoring (pressing) the tamper switch.

LED Does not light upon transmission of supervision messages.

Rearm Timer: Rearms the detector 2 minutes after the last alarm.

Timer disabled in the walk test mode – not applicable for the DD243

version (see section 1).

WIRELESS

Frequency (MHz): 315 (U.S. version), 433.92, 868.95, 869.2625 or

other frequency according to local requirements.

Transmission Sequence: 3 data bursts at variable intervals within 3 sec.

Encoding: 24-bit ID, over 16 million possible combinations.

Total Message Length: 36 bits.

Tamper Alert: Reported when a tamper event occurs and in any

subsequent message, until the tamper switch is restored.

Supervision Message: Signaling at 60 minutes interval (U.S. version),

15 minute interval (UK version) or according to local standards.

MOUNTING

Height: 1.8 — 2.4 m (6 — 8 ft). For NEXT PLUS K9-85 MCW, the

recommended height is up to 2.1 m (7 ft)

Installation Options: Surface or corner.

ACCESSORIES:

BR-1: Surface mounted swivel bracket, adjustable 30° down and 45°

left/45° right.

BR-2: BR-1 with a corner adapter

BR-3: BR-1 with a ceiling adapter

ENVIRONMENTAL

RFI Protection: >20 V/m up to 2000 MHz.

Operating Temperatures: -10°C to 50°C (14°F to 122°F).

Storage Temperatures: -20°C to 60°C (-4°F to 140°F).

Compliance with Standards: Designed to meet FCC Part 15 and Directive

1999/5/EC of the European Parliament. En 50131-1 Grade 2 (detector with back

tamper switch) / Grade 1 (detector without back tamper switch), Class II.

PHYSICAL

Size (H x W x D): 94.5 x 63.5 x 53.0 mm (3-11/16 x 2-1/2 x 2-1/16”).

Weight (with battery): 70 g (2.5 oz).

Color: White.

PATENTS: U.S. Patents 5,693,943 z 6,211,522 z D445,709 (another

patent pending).

3. INSTALLATION

3.1 General Guidance (see fig. 3)

1. Keep away from heat

sources.

2. Do not expose to air drafts.

3. Do not install outdoors.

4. Avoid direct sunshine.

5. Keep wiring away from power

cables.

6. Do not install behind partitions.

7. Mount on solid stable surface.

Important! The K9-85 detector is immune to 38 kg (85 lb)

animals moving on the floor or climbing on furniture as long as

the activity takes place below 1 m (3 ft). Above the 1 m (3 ft)

height limit, the detector is immune to 19 kg (42 lb) pets, but

the pet immunity will decrease as the pet gets closer to the

detector. It is therefore recommended to select a mounting

location that minimizes potential close proximity of animals.

3.2 Installation Procedure

1. Mounting — see fig. 4.

2. Battery installation (see fig. 4 and the note below)

3. Detector reset:

With the battery in place, press both tamper switches

simultaneously (see fig. 4) and release them. The front LED will

flash for about 2 minutes until the detector stabilizes.

Note: The detector transmits a low battery signal upon detection of

low voltage. It is recommended to wait about 1 minute after battery

removal, before inserting the new battery.

4. Enrolling:

Enroll the detector’s ID into the alarm system memory according to

the alarm system insallation instructions. When you are instructed

to transmit, press both tamper switches again and release them.

You may enroll the detector’s ID while the detector’s LED flashes.

5. Jumpers settings — see fig. 5.

6. Walk-test the coverage area — see fig. 2 and the note below. Walk

across the far end of coverage pattern in both directions. The LED

should light for 2-3 seconds each time your motion is detected.

Important! Instruct the user to walk test at least once a week to

verify proper function of the detector.

Note: Upon battery insertion or closing the cover (which results in

closing the tamper switch) the LED flashes for 2 min and the detector

goes into walk-test mode for 15 min. In walk-test mode, regardless of

the LED jumper position, the LED lights upon every motion detection.

After 15 minutes the detector automatically enters normal mode in which

the LED functions according to the LED control jumper position.