Search
Product Downloads
Product Software
DSE9460
12/24 volt 5 amp Enclosed Intelligent Battery Charger
Product Downloads
y Product Declaration of Conformity
y Data Sheet
y Data Sheet (US)
y DSE9460 & DSE9461 Operator Manual
y Installation Instructions
y Typical Wiring Diagram (CAD)
y Training Document — PC Configuration Interfacing (english)
y Training Document — USB Earth Loops and Isolation (english)
y Software Manual — DSE94xx PC Software manual (english)
y Software Manual — DSE Configuration Suite Software Installation Manual (english)
y Software Manual — DSEAssistant PC Software Manual (english)
|
Detail Specifications: 1059/1059510-dse9460.pdf file (22 Mar 2023) |
Accompanying Data:
DSE DSE9460 Battery Charger PDF Operator’s Manual (Updated: Wednesday 22nd of March 2023 02:23:29 AM)
Rating: 4.4 (rated by 39 users)
Compatible devices: DSE9701, Pocket Power 7800, EVP Series, DSE9474, DSE9473, wiCHARGE, SCB5650NB, DSE9462.
Recommended Documentation:
Text Version of Operator’s Manual
(Ocr-Read Summary of Contents, UPD: 22 March 2023)
-
30, DSE DSE9460 Operation 30 6.2 OPERATION OF LCD DISPLAY NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: An external remotely connected LCD display can be added to models without the enclosure mounted display. DSE Part Number 2541-02. 6.2.1 BACKLIGHT The LCD backlight is ON while the module is powered and flashes up det…
-
9, Specifications 9 3.4 OUTPUT SPECIFICATIONS 3.4.1 DSE9460 24V/12V 5A Parameter Min Nominal Max Comments Output Voltage 9V Configurable 29.5V Output Charging Current (A) 2A 5A 6A Current limit threshold (A) 5A 6A Recovery from current limit (A) 5A 6A Full load AC input current (A) 1.5A At Vin=230 V, Vo=28.2 V…
-
12, DSE DSE9460 Specifications 12 0 20 40 60 80 100 120 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 110V < Vin < 305V Charger De-rating Curve 0 10 20 30 40 50 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 90V < Vin < 110V Charger De-rating Curve
… -
25, DSE DSE9460 Operation 25 5.2.3 FAULT CONDITIONS Condition LED DESIGNATION FAULT 1 FAULT 2 High Output Voltage (DC) Red Constant Off High / Low Input Voltage (AC) or High Output Current (DC) Red Flashing Off High Ambient / Charger Temperature, High Battery Temperature (if enabled) Off Red Constant Short Circuit/ Reverse Polarity (DC Output Connection…
-
2, DSE Enclosed Intelligent Battery Charger Operator Manual 2 Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44 (0) 1723 890099 Sales Fax: +44 (0) 1723 893303 E-mail: [email protected] Website: www.deepseaplc.com DSE Enclosed Intelligent Battery Charger Operator Manual © Deep Sea Electronics Plc All rights reserved. No p…
-
6, Specifications 6 3 SPECIFICATIONS 3.1 PART NUMBERING 9460 — 001 — 00 NOTE: DSE9460 Chargers are factory preconfigured for max 5A charging. However the maximum current can be adjusted between 1A and 5A using DSE Configuration Suite PC Software. NOTE: DSE9461 Chargers are factory pre…
-
27, Operation 27 Charging time Charge time is often of little consequence when the battery is used in a standby operation. An example of this is when the battery is used to supply the starting system of a diesel generator. During normal operation, the battery is at full capacity and the battery charger is used to maintain the float voltage of the battery. The battery is…
-
10, Specifications 10 0 20 40 60 80 100 120 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 110V < Vin < 305V Charger De-rating Curve 0 10 20 30 40 50 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 90V < Vin < 110V Charger De-rating Curve
… -
5, Bibliography 5 1 BIBLIOGRAPHY This document refers to and is referred to by the following DSE publications which can be obtained from the DSE website www.deepseaplc.com 1.1 INSTALLATION INSTRUCTIONS Installation instructions are supplied with the product in the box and are intended as a ‘quick start’ guide only. DSE PART DESCRIPTION 053-1…
-
20, Installation 20 4.2.1.1 CONNECTOR A NOTE: — Connection from battery charge must be directly connected to the battery. Terminal Function Recommended size Comments Load negative 1mm² (AWG 16) Battery negative terminal Load Positive 1mm² (AWG 16) Battery positive terminal 4.2.1.2 CONNECTOR B / C NOTE: Screened 120Ω Ω…
-
35, DSE DSE9460 Operation 35 6.2.8.3 PRODUCT INFO 6.2.8.4 CONTROL MODE Control State Icon displayed On Off Boost Product info screen icon Shows model and firmware version of currently connected battery charger. Control mode screen icon Shows current operating mode
…
Recommended Instructions:
SIC 76, ARC-930SB, DP5000, MD-MT45H
-
# 2027014www.ikarus.net2029003-1007Bedienungsanleitung für Multi-LaderSehr geehrter Kunde,dieser Multi-Lader wurde insbesondere für kleine und mittelgrosse Akkus für ShockFlyer und Helikopter entwickelt. Es ist möglich 4-10 NiCd/NiMH Zellen oder 1-4 Li-Po Zellen zu laden.Technische Daten:Eingangs-Spannung: 12 V Auto Batterie oder stabilisiertes 12-13,8 V Stromversorgungsteil, minimu …
Multi-Charger 4
-
DATA PLATFORM GL7000 Quick Start Guide GL7000-UM-855Thank you for purchasing Graphtec DATA PLATFORM GL7000. The Quick Start Guide is to assist you with the basic operations. For detailed instructions, please refer to the instruction manual on the CD-ROM (PDF format) enclosed.Check the outer casing rstCheck the exterior of the unit to ensure that there a …
gl7000 24
-
digicharger vario proD Bedienungsanleitung Operating instructiOnsF Manuel d‘utilisatiOn ИнструкцИя по эксплуатацИИI istruziOne d’usOH Kezelési útMutatóE instrucciOnes de usO rOKasgrāMata VadOVas KäyttöOhjeS Manual Manual geBruiKsaanwijzing příručKa Kasutusjuhend náVOd na pOužíVanie instructiuni …
vario pro 5
-
WorkShopCharger 35Awww.defa.com- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.- Children shall not play with the appl …
WorkShopCharger 35A 30
Additional Information:
Popular Right Now:
Operating Impressions, Questions and Answers:
Download Operator’s manual of DSE DSE9460 Battery Charger for Free or View it Online on All-Guides.com.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
DSE ENCLOSED INTELLIGENT BATTERY CHARGER OPERATOR MANUAL ISSUE 2
DEEP SEA ELECTRONICS PLC
DSE ENCLOSED INTELLIGENT BATTERY
CHARGER OPERATOR MANUAL
Document Number: 057-176
Author: Anthony Manton
Table of Contents for DSE DSE9460:
-
Operation 23 5 INDICATIONS 5.1 LCD DISPLAY NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: For details of controls and LCD indication, see the section entitled Operation elsewhere in this document. 5.1.1 CHARGER STATUS Condition LED State Charger off OFF Charger on Constant Red 5.1.2 FAULT STATUS Condition LED State No Fault OFF Warning Fault Constant Red Sh
-
Operation 37 6.3 FRONT PANEL EDITOR 6.3.1 ACCESSING THE FRONT PANEL EDITOR The front panel editor (FPE) is accessed by pressing and holding the () button. During the transfer of the configuration file from the battery charger to the display module, the File Transfer progress screen is displayed. When the transfer is completed the first parameter is displayed: The first parameter is displayed. 6.3.2 SELECTING A PARAMETER • Press (+)
-
Operation 25 5.2.3 FAULT CONDITIONS Condition LED DESIGNATION FAULT 1 FAULT 2 High Output Voltage (DC) Red Constant Off High / Low Input Voltage (AC) or High Output Current (DC) Red Flashing Off High Ambient / Charger Temperature, High Battery Temperature (if enabled) Off Red Constant Short Circuit/ Reverse Polarity (DC Output Connection) Off Red Flashing 5.3 ENCLOSURE MOUNTED ANALOGUE METERS NOTE: — Enclosure mounted analogue meters are fitted only to the following model numbers :
-
Operation 29 11.5 12 12.5 13 13.5 14 14.5 15 -20 -10 0 10 20 30 40 50 60 Voltage (Volts) Temperature (ºC) Battery Temperature Compensation (Configured to 12V) Calcium Lead Acid Antimony VRLA — AGM VRLA-GEL Wet (Vented) Lead Acid NiCd 10/20 NICd 9/18
-
Specifications 12 0 20 40 60 80 100 120 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 110V < Vin < 305V Charger De-rating Curve 0 10 20 30 40 50 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 90V < Vin < 110V Charger De-rating Curve
-
Installation 22 4.3 DSE2541 ENCLOSURE MOUNTED DISPLAY MODULE NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: Where factory fitted to the enclosure, the DSE2541-01 must not be removed. Should an external, remote display be required, use DSE Part Number 2541-02 suitable for remote location up to 1.2km from the host battery c
-
Installation 21 4.2.2 TYPICAL CONNECTION DIAGRAM
-
Operation 26 6 OPERATION The DSE battery charger can be used as a battery charger, DC power supply, or both at the same time. For instance, the unit can be used to power the generator control panels and charge the panel batteries or starter batteries at the same time. With no AC input to the charger, the Charge fail relay is de-energised. This can be used to provide indication of charger failure which operates upon mains supply AC supply failure or battery charging failure. When a suitable AC supply
-
Operation 43 8 FAULT DIAGNOSIS Nature of problem Suggest ion The charger is not operating Check that the incoming AC supply is correctly connected and within limits and check the integrity of any external fuse that may be fitted. Ensure the charger is not being operated above the maximum temperature specification. Charge fail relay continuously operated Check the connected load of
-
Specifications 13 3.5 COMMUNICATION PORTS Communication Specification USB Port USB2.0 Device for connection to PC running DSE Configuration Suite Max distance 6m (20 feet) RS485 Serial Port Isolated Data connection 2 wire + common Half Duplex Data direction control for Transmit (by s/w protocol) Max Baud Rate 19200 External termination required (120Ω) Max common mode offset 70V (on board protection transorb) Max distance 1.2km (¾ mile) Display Communication Port Reserved for connection to fascia mounted LCD dis
-
Operation 32 6.2.7 CHARGE GRAPHIC The LCD shows the charge graphic to show the selected charge curve. The currently active mode is shown flashing in the module display. 6.2.7.1 THREE STAGE CHARGE PROFILE Detail of charge curve display NOTE: — A description of each charge mode is given earlier in this manual. Flashing to show charge mode Boost (Bulk) charge mode Absorption charge mode Float charge mode
-
DSE ENCLOSED INTELLIGENT BATTERY CHARGER OPERATOR MANUAL ISSUE 2 DEEP SEA ELECTRONICS PLC DSE ENCLOSED INTELLIGENT BATTERY CHARGER OPERATOR MANUAL Document Number: 057-176 Author: Anthony Manton
-
Specifications 9 3.4 OUTPUT SPECIFICATIONS 3.4.1 DSE9460 24V/12V 5A Parameter Min Nominal Max Comments Output Voltage 9V Configurable 29.5V Output Charging Current (A) 2A 5A 6A Current limit threshold (A) 5A 6A Recovery from current limit (A) 5A 6A Full load AC input current (A) 1.5A At Vin=230 V, Vo=28.2 V, Io=5 Amp Full load AC input current (A) 2.5A At Vin=110 V, Vo=28.2 V, Io=10 Amp AC Input Inrush (10ms) current (A) 60A For 10ms 0.780 0.8
Questions, Opinions and Exploitation Impressions:
You can ask a question, express your opinion or share our experience of DSE DSE9460 device using right now.
Download or browse on-line these Operator’s Manual for DSE DSE9460 Battery Charger.
Summary of Contents:
 |
[Page 1] DSE DSE9460 DSE ENCLOSED INTELLIGENT BATTERY CHARGER OPERATOR MANUAL ISSUE 2 DEEP SEA ELECTRONICS PLC DSE ENCLOSED INTELLIGENT BATTERY CHARGER OPERATOR MANUAL Document Number: 057-176 Author: Anthony Manton … |
 |
[Page 2] DSE DSE9460 DSE Enclosed Intelligent Battery Charger Operator Manual 2 Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44 (0) 1723 890099 Sales Fax: +44 (0) 1723 893303 E-mail: [email protected] |
 |
[Page 3] DSE DSE9460 DSE Enclosed Intelligent Battery Charger Operator Manual 3 TABLE OF CONTENTS 1 BIBLIOGRAPHY …………………………………………………………………………………….. 5 1.1 INSTALLATION INSTRUCTIONS …………….. |
 |
[Page 4] DSE DSE9460 DSE Enclosed Intelligent Battery Charger Operator Manual 4 8 FAULT DIAGNOSIS ………………………………………………………………………………. 43 9 MAINTENANCE, SPARES, REPAIR AND SERVICING ……………………… |
 |
[Page 5] DSE DSE9460 Bibliography 5 1 BIBLIOGRAPHY This document refers to and is referred to by the following DSE publications which can be obtained from the DSE website www.deepseaplc.com 1.1 INSTALLATION INSTRUCTIONS Installation instructions a… |
 |
[Page 6] DSE DSE9460 Specifications 6 3 SPECIFICATIONS 3.1 PART NUMBERING 9460 — 001 — 00 NOTE: DSE9460 Chargers are factory preconfigured for max 5A charging. However the maximum current can be ad… |
 |
[Page 7] DSE DSE9460 Specifications 7 3.2 PROTECTION • High Output Voltage (DC) detection. • High / Low Input Voltage (AC) detection. • Current limit to charger specification (5A or 10A depending upon charger model) with High Output Current detection. �… |
 |
[Page 8] DSE DSE9460 Specifications 8 3.3 ELECTRICAL SPECIFICATIONS Parameter Min Nominal Max AC Input Voltage (V) 95V 110V-277V 305V Operating Temperature -30°C 85°C with de-ratings Input F requency (Hz) 48Hz 64Hz Outp… |
 |
[Page 9] DSE DSE9460 Specifications 9 3.4 OUTPUT SPECIFICATIONS 3.4.1 DSE9460 24V/12V 5A Parameter Min Nominal Max Comments Output Voltage 9V Configurable 29.5V Output Charging Current (A) 2A 5A 6A Current limit threshold (A) … |
 |
[Page 10] DSE DSE9460 Specifications 10 0 20 40 60 80 100 120 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 110V < Vin < 305V Charger De-rating Curve 0 10 20 30 40 50 051015202530354045505560657075808590 Nominal … |
 |
[Page 11] DSE DSE9460 Specifications 11 3.4.2 DSE9461 24V/12V 10A Parameter Min Nominal Max Comments Output Voltage 9V Configurable 30.5V Output Charging Current (A) 2A 10A 11A Current limit threshold (A) 10A 11A R… |
 |
[Page 12] DSE DSE9460 Specifications 12 0 20 40 60 80 100 120 051015202530354045505560657075808590 Nominal Current (%) Temperature (ºC) De-rating Curve 110V < Vin < 305V Charger De-rating Curve 0 10 20 30 40 50 051015202530354045505560657075808590 Nomin… |
 |
[Page 13] DSE DSE9460 Specifications 13 3.5 COMMUNICATION PORTS Communication Specification USB Port USB2.0 Device for connection to PC running DSE Configuration Suite Max distance 6m (20 feet) RS485 Serial Port Isolated Data connection 2 wire + com… |
 |
[Page 14] DSE DSE9460 Specifications 14 3.5.2 RS485 The RS485 port on the battery charger supports the Modbus RTU protocol. RS485 is used for point-to-point cable connection of more than one device (maximum 32 devices) and allows for connection to PCs, PLCs and … |
 |
[Page 15] DSE DSE9460 Specifications 15 3.5.2.1 RECOMMENDED RS485 EXPANSION FOR DESKTOP AND LAPTOP PC’S • Brainboxes PM154 PCMCIA RS485 card (for laptops PCs) Set to ‘Half Duplex, Autogating” with ‘CTS True’ set to ‘enabled’ • Brainboxes VX-… |
 |
[Page 16] DSE DSE9460 Specifications 16 3.7 DIMENSIONS AND MOUNTING Parameter Comment Cabinet type Custom cabinet for indoor use only Overall size (see below for diagram) 165 mm x 305 mm x 110 mm (6.5” x 12” x 4.3”) Material: Sheet steel enclos… |
 |
[Page 17] DSE DSE9460 Specifications 17 3.8 APPLICABLE STANDARDS BS 4884-1 This document conforms to BS4884-1 1992 Specification for presentation of essential information. BS 4884-2 This document conforms to BS4884-2 1993 Guide to content. BS 4884-3 This docum… |
 |
[Page 18] DSE DSE9460 Installation 18 4 INSTALLATION The DSE battery charger is fit-and-forget. It can be permanently connected to the supply and the load, with no requirement to disable the charger during times of heavy load (such as engine cranking). 4.1 … |
 |
[Page 19] DSE DSE9460 Installation 19 4.2 USER CONNECTIONS Parameter Comm ent Connection type Screw terminal, rising clamp, no internal spring Min cable size 0.5mm² (AWG 20) Max cable size 2.5mm² (AWG 14) Recommended AC fuse 230V AC Input … |
 |
[Page 20] DSE DSE9460 Installation 20 4.2.1.1 CONNECTOR A NOTE: — Connection from battery charge must be directly connected to the battery. Terminal Function Recommended size Comments Load negative 1mm² (AWG 16) Battery negative terminal … |
 |
[Page 21] DSE DSE9460 Installation 21 4.2.2 TYPICAL CONNECTION DIAGRAM |
 |
[Page 22] DSE DSE9460 Installation 22 4.3 DSE2541 ENCLOSURE MOUNTED DISPLAY MODULE NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: Where factory fitted to the enclosure, the DSE2541-01 must not be remov… |
 |
[Page 23] DSE DSE9460 Operation 23 5 INDICATIONS 5.1 LCD DISPLAY NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: For details of controls and LCD indication, see the section entitled Operation els… |
 |
[Page 24] DSE DSE9460 Operation 24 5.2 ENCLOSURE MOUNTED LEDS NOTE: — Enclosure mounted LED indicators are fitted only to the following model numbers : 9460-03, 9460-04, 9461-03, 9461-04 5.2.1 STATUS Condition LED DESIGNATION OPE Yellow/Green… |
 |
[Page 25] DSE DSE9460 Operation 25 5.2.3 FAULT CONDITIONS Condition LED DESIGNATION FAULT 1 FAULT 2 High Output Voltage (DC) Red Constant Off High / Low Input Voltage (AC) or High Output Current (DC) Red Flashing Off High Ambient / Charger Temp… |
 |
[Page 26] DSE DSE9460 Operation 26 6 OPERATION The DSE battery charger can be used as a battery charger, DC power supply, or both at the same time. For instance, the unit can be used to power the generator control panels and charge the panel batteries or starter b… |
 |
[Page 27] DSE DSE9460 Operation 27 Charging time Charge time is often of little consequence when the battery is used in a standby operation. An example of this is when the battery is used to supply the starting system of a diesel generator. During normal operation, t… |
 |
[Page 28] DSE DSE9460 Operation 28 23 24 25 26 27 28 29 30 -20 -10 0 10 20 30 40 50 60 Voltage (Volts) Temperature (ºC) Battery Temperature Compensation (Configured to 24V) Calcium Lead Acid Antimony VRLA — AGM VRLA — AGM Wet (Vented) Lead Acid NiCd 10/2… |
 |
[Page 29] DSE DSE9460 Operation 29 11.5 12 12.5 13 13.5 14 14.5 15 -20 -10 0 10 20 30 40 50 60 Voltage (Volts) Temperature (ºC) Battery Temperature Compensation (Configured to 12V) Calcium Lead Acid Antimony VRLA — AGM VRLA-GEL Wet (Vented) Lead Acid NiCd… |
 |
[Page 30] DSE DSE9460 Operation 30 6.2 OPERATION OF LCD DISPLAY NOTE: LCD display is fitted only to the following model numbers : 9460-01, 9460-02, 9461- 01, 9461-02 NOTE: An external remotely connected LCD display can be added to models without the enclosure m… |
 |
[Page 31] DSE DSE9460 Operation 31 6.2.4 SUMMARY SCREEN The Summary Screen is initially displayed when the charged is turned on, and subsequently after a period of inactivity. 6.2.5 LINK ICON The link icon indicates a successful link to the ba… |
 |
[Page 32] DSE DSE9460 Operation 32 6.2.7 CHARGE GRAPHIC The LCD shows the charge graphic to show the selected charge curve. The currently active mode is shown flashing in the module display. 6.2.7.1 THREE STAGE CHARGE PROFILE Detail of charge curve … |
 |
[Page 33] DSE DSE9460 Operation 33 6.2.7.2 FOUR STAGE CHARGE PROFILE Detail of charge curve display NOTE: — A description of each charge mode is given earlier in this manual. Flashing to show charge mode Boost (Bulk)… |
 |
[Page 34] DSE DSE9460 Operation 34 6.2.8 VIEWING THE INSTRUMENTATION Press the navigation buttons (up) and (down) to cycle through the available instrumentation screens. All instrumentation screens have the following common icons : An icon is … |
 |
[Page 35] DSE DSE9460 Operation 35 6.2.8.3 PRODUCT INFO 6.2.8.4 CONTROL MODE Control State Icon displayed On Off Boost Product info screen icon Shows model and firmware version of currently co… |
 |
[Page 36] DSE DSE9460 Operation 36 6.2.8.5 ALARMS When a new alarm is detected, the LCD displays the alarm screen and the LCD backlight flashes. Press the () button to accept the alarm, exit the alarm screen and return to the summary screen. … |
 |
[Page 37] DSE DSE9460 Operation 37 6.3 FRONT PANEL EDITOR 6.3.1 ACCESSING THE FRONT PANEL EDITOR The front panel editor (FPE) is accessed by pressing and holding the () button. During the transfer of the configuration file from the battery charger to … |
 |
[Page 38] DSE DSE9460 Operation 38 6.3.3 FRONT PANEL EDITOR PARAMETERS 6.3.3.1 PAGE 1 – MISCELLANEOUS Index Configuration item Icon 100 Contrast 101 Temperature Units 102 Slave ID 103 Baud Rate 104 Enable Alarm Splash Scr… |
 |
[Page 39] DSE DSE9460 Operation 39 6.3.3.2 PAGE 2 – BATTERY TEMPERATURE Index Configuration item Icon 200 Battery Temperature Sensor Enable 201 Battery Temperature Warning Alarm Enable 202 Battery Temperature Warning Alarm Trip 203 Ba… |
 |
[Page 40] DSE DSE9460 Operation 40 6.3.3.5 PAGE 5 – MAINS Index Configuration item Icon 500 Mains Over Voltage Enable 501 Mains Over Voltage Alarm Trip 502 Mains Over Voltage Alarm Trip Delay 503 Mains Over Voltage Alarm Return … |
 |
[Page 41] DSE DSE9460 Operation 41 7 MODBUS The DSE Battery Charger supports the modbus RTU protocol over half-duplex RS485 communications. RS485 parameter Setting Start Bits 1 Data Bits 8 Parity None Stop Bits 2 Baud Rate Configurable using … |
 |
[Page 42] DSE DSE9460 Operation 42 Modbus parameter Value Modbus Register Start Address Page 166 Absolute HexaDecimal Address A600 Absolute Decimal Address 42496 (166 x 256). NOTE: Some Legacy Modbus Master devices may require a suffix of 40,000 to… |
 |
[Page 43] DSE DSE9460 Operation 43 8 FAULT DIAGNOSIS Nature of problem Suggest ion The charger is not operating Check that the incoming AC supply is correctly connected and within limits and check the integrity of any external fuse that may be fitted. … |
 |
[Page 44] DSE DSE9460 Maintenance, Warranty and Disposal 44 9 MAINTENANCE, SPARES, REPAIR AND SERVICING The DSE battery chargers are designed to be Fit and Forget. As such, there are no user serviceable parts. In the case of malfunction you should contact your … |
 |
[Page 45] DSE DSE9460 This Page is Intentionally Left Blank. |
 |
[Page 46] DSE DSE9460 This Page is Intentionally Left Blank. |
 |
[Page 47] DSE DSE9460 DSE ® COMPREHENSIVE FEATURE LIST TO SUIT A WIDE VARIETY OF BATTERY CHARGER APPLICATIONS DSE9460/9461 ENCLOSED INTELLIGENT BATTERY CHARGER 5 AMP & 10 AMP, 1… |
 |
[Page 48] DSE DSE9460 ® DSE DEEP SEA ELECTRONICS PLC UK Highfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PH TELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303 EMAIL [email protected] WEBSITE www.deepseaplc.com DEEP SEA ELECTRONICS I… |
 |
[Page 49] DSE DSE9460 Typical Wiring Diagrams 053-049 ISSUE 13 DSE9xxx Battery Charger Installation Instructions DEEP SEA ELECTRONICS DANGER OF DEATH : LIVE PARTS exist within the DSE9xxx enclosures. The enclosure cover must … |
 |
[Page 50] DSE DSE9460 NOTE : DSE9000 series chargers are designed to be mounted with the base to a vertical surface with the terminal strips at the bottom. NOTE : This document is intended as a ‘quick start’ guide only. For full operating instruct… |
© 2023
Manualzz provides technical documentation library and question & answer platform.Its a community-based project which helps to repair anything.
About us
DMCA / GDPR
Report
FixFr.com
The information herein is for personal use and informational purposes only. These documentations are only intended for a qualified person who is aware of the respective safety regulations and hazards. Products names, logos, brands and other trademarks are the property of their respective trademark holders in the USA and other countries.
Disclaimer | Privacy Policy | Terms and Conditions | XML Sitemap | HTML Sitemap
Copyright © 2011-2023 | Manual-Hub.com | All Rights Reserved.